1994 MAZDA MX-5 oil

ENGINE STAND MOUNTING PROCEDURE Ste~ 1 ~emove in the order shown in the figure. O-RING,, REPLACE 1. Exhaust manifold insulator 5. Water inlet pipe 2. Exhaust manifold 6. PIS oil pump bracket (If equipped) 3. Water bypass pipe 7. Idler pulley (NC) (If equipped) 4. NC compressor bracket (If equipped) 8. Left engine mount Step 2 1. Install the SST (engine hanger) using the holes shown in the figure. Gartner Banana

DISASSEMBLY AUXILIARY PARTS 1. Drain the engine oil. 2. Disassemble in the order shown in the figure. 1. Ignition coil and high-tension lead 2. Crankshaft position sensor 3. Manifold bracket 4. Intake manifold assembly 5. Alternator 6. Alternator bracket 7. Right engine mount 8. Oil filter 9. Oil cooler 10. Oil pressure switch 11. Water outlet pipe 12. Spark plug 13. Dipstick and pipe 14. Engine hanger Gartner Banana

DISASSEMBLY Disassembly Note Camshaft pulley 1. Hold the camshaft with a wrench at the cast hexagon. 2. Remove the camshaft pulley lock bolts. 3. Remove the camshaft pulleys. Camshaft 1. Loosen the camshaft cap bolts in two or three steps in the order shown in the figure. 2. Remove the camshaft caps. 3. Remove the camshafts. 4. Remove the camshaft oil seals from the camshafts. HLA Caution The HLA must be reinstalled in the same position from which they were removed. If they are not, it can cause premature and uneven wear. L Note Mark the HLA to show their original positions. Remove the HLA from the cylinder head. Cylinder head bolt 1. Loosen the cylinder head bolts in two or three steps in the order shown in the figure. 2. Remove the cylinder head bolts. Valve keeper 1. Set the SST against the upper valve spring seat as shown in the figure. 2. Compress the spring and remove the valve keepers. Gartner Banana

B DISASSEMBLY CYLINDER BLOCK (EXTERNAL PARTS) Disassemble in the order shown in the figure, referring to Disassembly Note. GASKET, REPLACE - L 1. Clutch cover, clutch disc (MT) Removal 1 Installation ......... section H 2. Flywheel (MT), drive plate (AT) Disassembly Note .......... page 8-43 3. End plate 4. Oil pan Disassembly Note .......... page B43 5. Oil strainer 6. Oil pan baffle Disassembly Note .......... page B-44 7. Water pump 8. Oil pump ...... Disassembly 1 Assembly section D 9. Front oil seal Disassembly Note .......... page B-43 10. Rear cover 11. Rear oil seal Disassembly Note .......... page 6-43 Gartner Banana

DISASSEMBLY B PROTECT PUMP BODY WlTH RAG 05UOBX-10; I PROTECT REAR COYER WITH RAG I Disassembly Note Flywheel (MT) or drive plate (AT) 1. Hold the flywheel with the SST. 2. Remove the flywheel lock bolts. 3. Remove the flywheel. Oil pan 1. Remove the oil pan mounting bolts. Caution Pry tools can easily scratch the cylinder block and oil pan contact surfaces. 2. Insert a screwdriver only at the points shown in the fig- ure. 3. Remove the oil pan. Oil pan baffle 1. Insert a screwdriver between the cylinder block and the baffle to separate them. 2. Remove the baffle. Front oil seal Remove the oil seal with a screwdriver protected with a rag. Rear oil seal Remove the oil seal with a screwdriver protected with a rag. Gartner Banana

B DISASSEMBLY CYLINDER BLOCK (INTERNAL PARTS) Disassemble in the order shown in the figure, referring to Disassembly Note. 1. Connecting rod cap Inspection ................. page B-45 2. Lower connecting rod bearing Inspection ................. page 8-45 3. Connecting rod and piston assembly Disassembly Note .......... page 545 4. Upper connecting rod bearing Inspection ................. page 8-57 5. Piston ring Disassembly Note .......... page 545 Inspection ................. page 555 6. Piston pin clip 7. Piston pin Disassembly Note Inspection ................. page 6-45 8. Piston Inspection ................. page 555 9. Connecting rod Inspection ................. page I345 10. Main bearing cap Disassembly Note .......... page 8-46 11. Lower main bearing Inspection ................. page B-46 12. Crankshaft Inspection ................. page 8-46 13. Upper main bearing Inspection ................. page 8-46 14. Thrust bearing Inspection ................. page 6-63 15. Oil jet Inspection ................. page B-53 16. Cylinder block Inspection ................. page 553 Gartner Banana

DISASSEMBLY Disassembly Note Connecting rod cap Before removing the connecting rod caps, measure the connecting rod side clearance. (Refer to page 8-64.) Connecting rod and piston assembly 1. Before removing the connecting rod and piston assem- bly, measure the connecting rod oil clearance. (Refer to page 8-64.) 2. Remove the Plastigage from the crankpin journals. 3. Use the handle of a hammer to remove the piston and connecting rod assembly through the top of the cylinder block. Piston ring Remove the piston rings with a piston ring expander (commercially available). Piston pin Remove the piston pin with the SST. Gartner Banana

DISASSEMBLY Main bearing cap 1. Before removing the main bearing caps, measure the crankshaft end play. (Refer to page B-64.) u 2. Loosen the main bearing cap bolts in two or three steps in the order shown in the figure. 3. Remove the main bearing caps. Crankshaft Before removing the crankshaft, measure the main bearing oil clearances. (Refer to page B-62.) Gartner Banana