1994 MAZDA MX-5 battery

AUDIO Clock The clock can be adjusted during radio, tape, or CD play. I Name I Illustration Clock button (clock display) ALC (Auto level controller) Name 1 Illustration ALCJbodysonic volume control knob I Mute button Roof mode button I Stereo-wide button Operation Press button to display present radio frequency or operation mode If power supply to unit is broken (burnt fuse or disconnected battery), clock setup will be canceled When clock button is pushed for 2 seconds, clock display flashes. At this point, press H button to advance hours and M button to advance minutes Press clock button again to return to normal display If clock button is pressed again while clock display is flashing and time has not been adjusted (that is, H and M buttons have not been pressed), min- utes will be set at :00. If time before adjustment showed 30-59 minutes, time will be set at next hour For example, Operation Press knob to turn ALC on or off 1. At ON, ALC adjusts sound corresponding to vehicle speed; ALC indica- tor light turns on 2. To adjust seat vibration, turn knob to right or left Right -t Seat vibration increases Left + Seat vibration decreases Turn knob right or left to transfer sound Right -+ Door speakers Left -t Headrest speakers Press button to lower overall volume by 10dB Press button to switch between roof-open mode and roof-closed mode; sound quality is adjusted depending on whether roof is opened or closed Press button to turn stereo-wide function on or off At ON, stereo-wide mode improves sound quality Gartner Banana

T AUDIO ANTITHEFT SYSTEM Alarm Conditions If the antitheft system protection has been activated, any one of the following conditions will trigger the sys- tem: .--' Disconnected battery cable Discharged battery Disconnected audio unit connectors. If the system is triggered, the audio unit will then be inoperative when it is reconnected to a power source, and "code" will flash on the display until the preselected code number is input. Follow the procedures in "Canceling Antitheft Operation" (page T-110) to deactivate the unit. Setting the Code Number 1. Turn the audio unit off with the ignition switch at ACC. 2. Push REW and FF simultaneously for approximately 2 seconds until "code" is displayed. 3. Push REW and FF together again within 10 seconds un- til bars appear on the display. 4. Select a personal code number and record it before in- putting it. If the number is input and then forgotten, it can- not be canceled, and if the unit is disconnected again, the audio unit will be inoperati. .-/ 5. Use channel buttons 1-4 to input the selected code number. Press 1 for the first digit, 2 for the second, 3 for the third, and 4 for the last digit. If the display is deleted, repeat the procedure from step 1. 6. With the code number displayed, press and hold REW and FF for approximately 2 seconds until a beep is heard and "code" begins to flash. 7. After approximately 5 seconds, the display will change to time. This indicates the system is set. Gartner Banana

AUDIO T Symptom: Speaker(s) do not operate (Without headrest speakers.) I L/ Possible cause Antitheft system activated Damaged audio unit Open circuit in wiring harness Poor connection of connector Damaged speaker Step 1 Check if the antitheft system has been activated. Turn the ignition switch to ACC and note the display. - - - Display CODE flashes Step 2 1. Remove the audio unit. (Refer to page T-145.) 2. Check the connections of the ground wire and the short plug. 3. If a connection is poor or loose, repair or replace it. 4. If the connections are OK, go to Step 3. Action Deactive antitheft system (page T-120) and go to step 2 Err flashes Clock No indication Step 3 1. Turn the ignition switch to ACC. 2. Measure the voltage at the following terminal-wires of the audio unit connector. B+: Battery positive voltage Have audio unit changed at a Panasonic service company Go to Step 4 Go to Ste~ 2 Terminal I Voltage I Action I B+ I Check C (UR) terminal 1 I 1, - I B+ I Redace audio unit I 1- Check ROOM 10A fuse (UR) I Other 1 If ROOM 10A fuse is OK, repair wiring harness 1 . . Check CIGAR 15A fuse If CIGAR 15A fuse is OK, repair wiring harness (CIGAR 15A fuse - Audio unit) A I I (ROOM 10A fuse - Audio unit) - I I Other Gartner Banana

T AUDIO Step 3 1. Turn the ignition switch to ACC. 2. Measure the voltage at the following terminal-wires of the audio unit connector. d B+: Battery positive voltage Action 1 rerminal Voltage + Check C (UR) terminal I Check CIGAR 15A fuse If CIGAR 15A fuse is OK, repair wiring harness (CIGAR 15A fuse - Audio unit) I A (uB) I Other If ROOM 10A fuse is OK, repair wiring harness (ROOM 10A fuse - Audio unit) Step 4 Locate the faulty speaker(s) by using the headrest speaker volume, and balance control. 1. Turn the ignition switch to ACC. 2. Play a prerecorded tape, and set the volume to the ten- ter position. .- 3. Set the head restraint speaker volume, and balance controls as shown in Table 2. Check operation of each speaker. 4. From results of Table 2 testing, go to the next step. I BALANCE CONTROL 45UOTX-246 Table 2 Judgement I Next Step I Speaker Left door I Left I Min Head restraint Speaker Ispeaker volume / operates Left door speaker circuit OK - Left door speaker circuit faultv 1 Step 5 Right door speaker circuit OK - Rinht door weaker circuit faultv Ste~ 5 (driver seat) faultv Step 8 Right door Left headrest (Driver seat) ---- Right headrest speaker circuit - (driver seat) OK Right headrest speaker circuit (driver seat) faultv Step 8 Right - Right headrest (Driver seat) Left headrest speaker circuit Left headrest (Passenger seat) Min Max - Max Yes No Yes No Right headrest (Passenger seat) Max 1 Max Yes I (passenger seat) OK I Right headrest speaker circuit bassenaer seat) faultv Gartner Banana

AUDIO I Symptom: No sound can be heard I Possible cause Burnt CIGAR fuse Burnt ROOM fuse Damaged audio unit ROOM 1 OA 35UOTX-077 Open circuit in wiring harness Poor connection of connector Damaged DIN cord Step 1 Check the CIGAR 15A fuse and ROOM 1 OA fuse in the fuse block. I Fuse 1 Action I Step 2 1. Remove the audio unit. (Refer to page T-145.) 2. Check the connectors and the DIN cord of the audio unit. 3. If a connection is poor or loose, repair or replace it. 4. If the connectors are OK, go to Step 3. Burnt OK Step 3 1. Turn the ignition switch to ACC position. 2. Measure voltage at terminals A (UB) and C (UR) of the AM-FM radio unit connector (1 2-pin). Replace fuse after checking and repairing wiring harness Go to Step 2 B+: Battery positive voltage Terminal 1 Voltfe Action Measure terminal C (VR) voltage Repair wiring harness (CIGAR fuse - AMeFM radio unit) Go to Step 4 Repair wiring harness (ROOM fuse - AM-FM radio unit) 1 Step 4 1. Check for continuity between body of the AM-FM radio unit and ground. I No Repair wiring harness (AM-FM radio unit - GND) 1 Continuity Yes Action Replace audio unit Gartner Banana

T AUDIO Step 14 1. Turn the ignition switch to ACC. 2. Measure the voltage at terminal C (UB) of the auto level controller connector (&pin). .J B+: Battery positive voltage I voltage Action Step 15 1. Disconnect the auto level controller DIN cord (&pin). 2. Measure the voltage at terminal 2 of the DIN cord. B+ Other Go to Step 15 Repair wiring harness CIGAR fuse - Auto level controller B+: Battery positive voltage Step 16 1. Check for continuity between the auto level controller connector (&pin) and the headrest speaker and body- sonic connector (&pin). Voltage B+ Other Action Go to Step 16 Replace AMFM radio unit 2. If correct, replace the auto level controller. 3. If not as specified, repair the wiring. I Speaker Right headrest Left headrest ALC I 'peaker connector connector H (VW) 8-pin +t C (LMI) 6-pin B (UO) &pin ++ D (LO) 6-pin F (RIL) &pin o B (RIL) Gpin A (W) &pin o A (W) 6-pin continuity Yes Yes Yes Yes .- / Gartner Banana

AUDIO T Symptom: Bodysonic will not play Possible cause Damaged bodysonic Damaged audio unit Damaged DIN cord Open or short circuit in wiring harness Poor connection of connector Open or short circuit in DIN cord 45UOTX-269 Step 1 1. Remove the audio unit. (Refer to page T-145.) 2. Make sure the audio unit connector and DIN cord are properly connected. 3. If the connections are OK, go to Step 2. 4. If a connection is poor, repair it. Step 2 1. TI~ the ignition switch to ACC. .. .-... 2. Measure fhe voltage at terminal C (UB) of the auto level controller connector (8-pin). B+: Battery positive voltage Step 3 1. Disconnect the auto level controller DIN cord (6-pin). Voltage B+ Other 2. Measure the voltage at terminal 2 of the DIN cord. Action Go to Ste~ 3 J Repair wiring harness (CIGAR fuse - Auto level controller) B+: Batterv ~ositlve voltage I Other I Replace AMaFM radio unit . . - Step 4 1. Make sure headrest speaker and bodysonic connectors are properly connected. 2. If the connections are OK, go to Step 5. 3. If a connection is poor, repair it. Voltage B+ Action Go to Stea 4 Gartner Banana

AUDIO Inspection c Fuse ness. ml JHFDB If the antenna fails to raise or lower, make the following checks: 1. Check the antenna fuse (10A). 2. Replace fuse after checking and repairing wiring har- Power antenna 1. Check for continuity between the terminals of the power antenna relay. If there is no continuity, replace the relay. Terminal I M: Continuity 2. If the antenna does not function even though there is continuity, the problem may be either in the wiring har- ness or in the audio component assembly. 3. Apply battery positive voltage to the terminals and check the operation. I I A 1 B 1 DOWN I Function of antenna UP Battery Pos. D Neg. A Gartner Banana