1994 MAZDA MX-5 light

ENGINE TUNE-UP HLA TROUBLESHOOTING GUIDE Problem 1. Noise when engine is started immediately af- ter oil is changed 2. Noise when engine is started after setting approx. one day 3. Noise when engine is started after cranking for 3 seconds or more 4. Noise when engine is started after new HLA is installed 5. Noise continues more than 10 minutes 5. Noise occurs during idle after high speed run- ning Possible Cause Oil leakage in oil passage Oil leakage in HLA Faulty HLA Action Run engine 2000-3000 rpm. If noise stops after 2 second-10 minutes(') HLA is normal. If not, replace HLA. Time required for engine oil to circulate withir engine, includes tolerance for engine oi condition and ambient temperature. Insufficient oil pressure (Refer to page 8-53) Press down HLA by hand. If it does not move, HLA is normal. If it moves, replace HLA. Check oil pressure. If lower than specification, check for cause. Oil pressure; 295-392 kPa I3.0-4.0 kgf/cm2, 43-56 psil-3000 rpm Deteriorated oil Check oil quality. If deteriorated, replace with specified type and amount of oil. Incorrect oil amount IGNITION TIMING, IDLE SPEED Preparation 1. Check the condition of the engine (spark plugs, leaks in hoses, etc.). 2. Make sure all accessories are OFF. 3. Warm up the engine to normal operating temperature. 4. Connect a timing light and a tachometer to the data link connector terminal IG-. When using an externally pow- ered timing light and/or tachometer, connect it to the power connector (Blue: 1 -pin). Measure valve clearance. If more than Omm {0 in}, replace HLA. Check oil level. Drain or add oil as necessary. Caution Grounding the power connector terminal (Blue: 1-pin) will burn out the 20A wiper fuse. 5. Make sure coolant fan does not operate. Gartner Banana

B ON-VEHICLE MAINTENANCE I - DOWEL PINS I 3. Apply silicone sealant to the shaded areas shown in the figure. Do not let any sealant get on the sealant surfaces. 4. Install the camshaft caps according to the cap number and arrow mark. 5. Install the camshaft cap bolts and tighten them in two or three steps in the order shown in the figure. Tightening torque: 11.3-1 4.2 N.m (115--145 kgf.cm, 100-125 in-lbf} ii 6. Apply a small amount of clean engine oil to the lip of a new camshaft oil seal. 7. Push the oil seal slightly in by hand. 8. Using a pipe and hammer, tap the oil seal in evenly until it is flush with the edge of the camshaft cap. Note Oil seal outer diameter: 48mm {I .89 in) Oil seal inner diameter: 34mm {I .34 in} Camshaft pulley 1. Turn the camshafts until the camshaft dowel pins face straight up. 2. Install the camshaft pulleys with the I mark (intake side) or the E mark (exhaust side) straight up. Gartner Banana

ON-VEHICLE MAINTENANCE B Steps After Installation 1. Connect the neaative batterv cable. Oil seal 1. Cut the oil seal lip with a razor knife. 2. Remove the oil seal with a screwdriver protected with a rag. Installation Note Oil seal 1. Apply a small amount of clean engine oil to the lip of a new oil seal. 2. Push the oil seal slightly in by hand. 3. Tap the oil seal in evenly with a pipe and a hammer until it is flush with the edge of the oil pump body. Note Oil seal outer diameter: 50.5mm (1.99 in} Oil seal inner diameter: 36.5mm (1.44 in} Timing belt pulley 1. Install the timing belt pulley. 2. Install the pulley woodruff key with the tapered side to- ward the oil pump body. 2. Start the enginsand check, and if necessary, adjust the ignition timing. 3. Connect the negative battery cable. 4. Start the engine and check follows: (1) Engine coolant leakage (2) Ignition timing (Refer to page B-9.) 5. Recheck the engine coolant levels. Gartner Banana

ON-VEHICLE MAINTENANCE Installation Note Oil seal 1. Apply a small amount of clean engine oil to w new oil seal. 2. Push the oil seal slightly in by hand. 3. Using a pipe and hammer, tap the oil seal in it is flush with the edge of the rear cover. Note Oil seal outer diameter: 100mm (3.94 in} Oil seal inner diameter: 83mm (3.27 in} 45UOBX-049 Steps After Installation 1. Connect the negative battery cable. 2. Start the engine and perform engine adjustments as necessary. the lip of a evenly until Gartner Banana

ASSEMBLY B CYLINDER BLOCK (EXTERNAL PARTS) Torque Specifications 7.9-10.7 Nm (80-110 kgfwn, 70--95.4 in4bf) OIL SEAL. NEW 7.9-10.7 Nm (80-110 kgfcm, 7045.4 Indbf) Nm (kgf m, ftlbf) 05UOBX-198 Rear Cover 1. Apply a small amount of clean engine oil to the lip of a new oil seal. 2. Push the oil seal slightly in by hand. 3. Using a pipe, press the oil seal in evenly until it is flush with the edge of the rear cover. L Note Oil seal outer diameter: 100mm (3.94 in} Oil seal inner diameter: 83mm (3.27 in} Gartner Banana

ASSEMBLY 4. Apply silicone sealant to the shaded area shown in the figure. 5. Install the rear cover Tightening torque: 7.9-1 0.7 N.m (80-1 10 kgfem, 70-95.4 in-lbf) Oil Pump 1. Apply a small amount of clean engine oil to the lip of a new oil seal. 2. Push the oil seal slightly in by hand. 3. Using a pipe, press the oil seal in evenly until it is flush with the edge of the oil pump body. U' Note Oil seal outer diameter: 50.5mm (1.99 in} Oil seal inner diameter: 36.5mm (1.44 in) 4. Install the oil pump and a new gasket. Tightening torque: 19-25 N.m (1 -9-2.6 kgf-m, 14--18 ft-lbf) 5. Cut away the portion of the gasket that projects from the body toward the oil pan side. Gartner Banana

B ASSEMBLY @ @ GREATER THAN @ @ 1. Assemble the SST so that depth L is as specified. Depth L: 18.3-18.9mm (0.721-0.744in) 2. Slide the valve seal onto the valve guide. 3. Set the SST against the valve seal. 4. Press the valve seal in until the SST contacts the cylin- der head. Valve and Valve Spring 1. lnstall the lower spring seat. 2. Install the valve. 3. lnstall the valve spring with the closer pitch toward the cylinder head. 4. lnstall the upper spring seat. 5. Compress the valve spring with the SST, and install the valve keepers. 6. Remove the SST. 7. Tap the end of the valve stem lightly two or three times with a plastic hammer to verify that the keepers are all fully seated. Gartner Banana

ASSEMBLY Camshaft Note The rear end of exhaust camshaft is grooved for the L/ crankshaft position sensor drive. 1. Apply clean engine oil to the camshaft journals and bear- ings. 2. Install the camshaft in position. CRANKSHAFT POSITION SENSOR DRIVE GROOVE 45UOBX-151 3. Apply silicone sealant to the shaded areas shown in the figure. Do not let any sealant get on the journal surfaces. 4. Install the camshaft caps according to the cap number and arrow mark. 5. Install the camshaft cap bolts, and tighten them in two or three steps in the order shown. Tightening torque: Il.3--14.2 N.m {ll5-l4S kgfem, 100-125 in4bf) ij 6. Apply a small amount of clean engine oil to the lip of a new camshaft oil seal. 7. Push the oil seal slightly in by hand. 8. Using a pipe and hammer, tap the oil seal in evenly until it is flush with the edge of the camshaft cap. Note Oil seal outer diameter: 48mm (1.89 in) Oil seal inner diameter: 34mm (1.34 in) Camshaft Pulley 1. Turn the camshafts until the camshaft dowel pins face straight up. 2. lnstall the camshaft pulleys with the I mark (intake side) or the E mark (exhaust side) straight up. Gartner Banana