1994 MAZDA MX-5 height adjustment

DETACHABLE HARDTOP PROTECTOR ADJUSTING NUT DETACHABLE HARDTOl WINDSHIELD HEADER I @ 1 5 r 2 (0.2 f 0.08) @ 1 0 r 2 (0 * 0.08) mm (in) 45UOSX-11 f Adjustment Top latch assembly 1. Lift the protector away from the top latch assembly ad- justing nut. d 2. Turn the adjusting nut clockwise to decrease clearance A and height B; turn the nut counterclockwise to increase them. 3. Secure the adjusting nut with the protector. I I Side latch assembly 1. Lift the protector away from the side latch assembly ad- justing nut. 2. Turn the adjusting nut clockwise to tighten the striker and side latch assembly engagement; turn the nut counter- clockwise to loosen the engagement. - 3. Secure the adjusting nut with the protector. ADJUSTING NUT 45UOSX-117 Rear deck latch assembly 1. Remove the screw and open the latch cover. 2. Loosen the plate mounting bolts. 3. Install the detachable hardtop to the body. 4. Move the plate right, left, fore, or aft until it is tight. 5. Tighten the plate mounting bolts. Tightening torque: 18-26 N.m (1.8-2.7 kgfsm, 14--19 ft-lbf) 6. Close the latch cover and install the screw. Gartner Banana

T LIGHTING SYSTEM Stoplight Switch Adjustment 1. Adjust the brake pedal height. (Refer to section P.) 2. Disconnect the stoplight switch connector. 4 3. Loosen the stoplight switch locknut. 4. Turn the stoplight switch until it contacts the pedal arm. Turn an additional 112 turn. 5. Tighten the locknut. Locknut tightening torque: 14-18 N.m (1.4-1.8 kgf-m, 120-156 in-lbf) I I I Brake pedal depress I 0 0 1 I Inspection Stoplight switch 1. Disconnect the stoplight switch connector. 2. Check for continuity between terminals of the switch. lnspection condition 3. If not as specified, replace the stoplight switch. Terminal A I B I Brake pedal released I m : Continuity Gartner Banana

CRUISE CONTROL SYSTEM T BRAKE AND STOPLIGHT SWITCH CLUTCH SWITCH Removal Loosen the locknut and remove the switch. Installation Install in the reverse order of removal. Adjustment Adjust the switch to set the specified pedal height. Pedal height: 175--185mm (6.89-7.82 in) Pedal free play: 0.6-3.lmm (0.02-4.12 in) Inspection 1. Disconnect the clutch switch connector. 2. Check for continuity between terminals of the switch. Pedal position Terminal A B 1 0-a: Continuity Pedal released 3. If not as specified, replace the clutch switch. Pedal de~ressed STOP LIGHTIBRAKE SWITCH Removal Loosen the locknut and remove the switch. 0 I 0 Installation Install in the reverse order of removal. Adjustment Adjust the switch to set the specified pedal height. Pedal height: l7l-l8l mm (6.93--7.13 in) Pedal free play: 4.0-7.0mm (0.16-0.28 in) Inspection 1. Disconnect the brake switch connector. 2. Check for continuity between terminals of the switch. I I I Pedal released I I I Pedal position w: Continuity Terminal Pedal depressed 3. If not as specified, replace the brake switch. 4. If the switch is OK, repair the wiring harness (fuse - brake switch - control unit). A 0 I 0 B Gartner Banana

ST SPECIAL TOOLS DIFFERENTIAL rooL NUMBER a DESCRIPTION PRIORITY TOOL NUMBER~ DESCRIPTION PRIORITY ILLUSTRATION 49 F027 005 Attachment @62 Hanger, differential carrier Collar Adjustment wrench, side bearing 49 8531 565 Pinion model 49 GO30 338 Attachment E 49 F027 004 Attachment @80 Gauge body, pinion height 49 BOO1 795 Installer, oil seal 49 0305 555 Sauge block 49 U027 003 Installer, oil seal nstaller, rubber wshing Holder, coupling ilange Gartner Banana