1994 MAZDA MX-5 battery

DOOR s DOOR COMPONENTS - Removal / Installation - - --- 1. Disconnect the negative battery cable. 2. Remove in the order shown in the figure. To remove the checker, remove the door trim and door screen. (Refer to page S-9.) 3. Install in thereverse order of removal. 1. Harness connector 2. Checker pin 3. Hinge 4. Door Adjustment . . . . . . . . . . . . . . . . . . page S-8 5. Checker Gartner Banana

WINDOW REGULATOR, GLASS, AND GUIDE S WINDOW REGULATOR, GLASS, AND GUIDE COMPONENTS Removal / Installation 1. Raise the door glass about 190 mm (7.5 in) from the fully open position. 2. Disconnect the negative battery cable. Note Remove the door screen carefully so that it may be reused. 3. Remove in the order shown in the figure, referring to Removal Note. 4. Install in the reverse order of removal, referring to lnstallation Note. 1. Regulator handle Removal Note . . Installation Note 2. lnner handle cover 3. Pull handle 4. Door trim Removal Note . . 5. lnner handle 6. Sealing pad 7. Door screen 8. Upper glass stopper 9. page S-10 ........... page S-10 ........... 10. 12. page S-61 ........... 13. Front beltline molding Removal Note ............. page S-28 Door glass Adjustment ................ page S-10 Window regulator Glass guide Door weatherstrip Division channel Quarter glass weatherstrip Quarter glass Speaker (if necessary) Dovetail (if necessary) Gartner Banana

DOOR LOCK AND OPENER s DOOR LOCK AND OPENER COMPONENTS Removal 1 lnstallation 1. Raise the door glass fully. 2. Disconnect the negative battery cable. Note Remove the door screen carefully so that it may be reused. 3. Remove in the order shown in the figure, referring Removal Note. 4. Install in the reverse order of removal, referring Installation Note. 1. Regulator handle 5. Inner handle Removal Note ............. page S-10 6. Sealing pad Installation Note ........... page S-10 7. Door screen - 2. Inner handle cover 8. Door lock assembly 3. Pull handle 9. Outer handle 4. Door trim 10. Key cylinder Removal Note ............. page S-61 Gartner Banana

POWER WINDOW SYSTEM Power windows do not operate w Turn ignition switch ON B+: Battery positive voltage Check P.WINDOW (30A) fuse W Shon circuit Disconnect power window main switch connector, check Repair harness (Main switch--Ground) continuity of terminal-wire (B) to ground Check for B+ at terminal-wire (BNV) of power window main switch connector 1 Check power window switch (Refer to page S-22) 1 45UOSX-016 One power window does not operate w --c NG' I Turn ignition switch ON I Repair harness (Fuse box-Main switch) Check for B+ at terminal-wires of power window main Check power window switch (Refer to page S-22) switch connector Up : (GIR), ((RIB)) wire Down: (G), ((RIG)) wire I Repair harness (Main switch-Motor) connector Up : G/R) wire Down: [G) wire Check power window regulator (Refer to page S-22) (( )): Passenger side Gartner Banana

s POWER WINDOW SYSTEM FDB POWER WINDOW SWITCH Inspection 1. Check for continuity between terminals of the switch with an ohmmeter. O--O: Indicates continuity 2. If not as specified, replace the switch. POWER WINDOW REGULATOR lnspection 1. Connect battery positive voltage to terminal A and L' ground terminal B of the motor connector. Verify that the motor operates. 2. Reverse the above connections and check for reverse operation of the motor. 3. If not as specified, replace the motor. Gartner Banana

s FRONT BUMPER FRONT BUMPER COMPONENTS Removal 1 Installation 1. Raise the headlights. 2. Disconnect the negative battery cable. 3. Remove in the order shown in the figure. 4. Install in the reverse order of removal. Front combination light 6. Set plate Removal .................... Section T 7. Front fascia Front side marker light 8. Retainer Removal .................... Section T 9. Bumper reinforcement 3. Fender bracket 10. Spacer 4. Mud guard 11. Front bumper retainer 5. Grille cover 12. Front bumper bracket Gartner Banana

REAR BUMPER s REAR BUMPER COMPONENTS L Removal 1 Installation 1. Disconnect the negative battery cable. 2. Remove in the order shown in the figure. 3. Install in the reverse order of removal. 1. Rear side marker light 2. Splash shield Removal . . . . . . . . . . . . . . . . . . . . Section T 3. Rear bumper Gartner Banana

OUTSIDE MIRROR Power outside mirrors do not operate 1 B+: Battery positive voltage 1 u Check CIGAR 15A fuse Replace fuse after checking and repairing wiring harness I Turn ignition switch to ON I ,,.,,,,,,,,,.,,,,.,. switch connector Repair harness (Fuse box - Power outside mirror switch) 1 OK I I I RIGHT i i~&) wire Disconnect power outside mirror switch connector Check for continuity between terminal wire (0) and ground Fbpair harness (Power outside mirror switch -Ground) 1 Check power outside mirror switch (Refer to page S-33) Reconnect power outside mirror switch connector Check for B+ at terminal wires of power outside mirror I I Switch position I Terminal I Voltage I UP I (BRl wire 1 B+ switch connector with mirror switch in positions indicated below NG c OK Right Left Check for B+ at terminal wires py of power outside mirror con- nector with mirror switch in positions indicated below Check power outside mirror (Refer to page S-33) - DOWN LEFT RIGHT UP DOWN LEFT RIGHT OK > ,- , - (LGIB) wire (LG/B) wire (B R/B) wire (BR) wire (LGIB) wire (LGIB) wire (BRIB) wire - Repair harness (Power outside mirror switch - Power outside mirror) B+ B+ B+ B+ B+ B+ B+ Gartner Banana