1994 MAZDA MX-5 wheel

GENERAL SERVICE INFORMATION SERVICE PRECAUTIONS ............................................ 2 JACKING AND SAFETY STAND POSITIONS ............ 8 VEHICLE LIFT (2-SUPPORT TYPE) POSITIONS ....... 8 TOW CABLE ATTACHMENT POSITIONS .................. 9 IDENTIFICATION NUMBER LOCATIONS ................... 9 VEHICLE DIMENSIONS ................................................ 10 WHEEL ALIGNMENT .................................................... 10 Gartner Banana

GENERAL SERVICE INFORMATION L ANTI-CORROSION TREATMENT When replacing body panels, always apply body sealer, anti-rust treatment. or undercoating ac- cording to the requirements of the market. Application of surface agent and body sealer After first applying the coating of surfacing agent, apply body sealer where necessary. Note For locations where application of body sealer is difficult after installation, apply .t-before the installation. Application of rust inhibitor Undercoating Apply rust inhibitor to the back of welded areas, Use antirust treatment for underbody welding using an installation hole or a gap near that spots and wheel housings. section. Gartner Banana

u GENERAL SERVICE INFORMATION TIEDOWN HOOK - FRONT /'-- TIEDOWN HOOK - REAR -?-A TOWING Proper towing equipments are necessary to prevent damage to the vehicle during any towing operation. Laws and regulations applicable to vehicles in tow must always be observed. Release the parking brake, place the shift lever in neutral, and set the ignition switch in the ACC posi- tion. As a rule, towed vehicles should be pulled with the driving wheels off the ground. WITH MANUAL TRANSMISSION If the transmission, rear axle, and steering system are not damaged, the vehicle may be towed on all four wheels. If any of these components are damaged, use a towing dolly. CAUTION The power assist for the brakes and steering are inoperable while the engine is off. Do not use the tiedown hooks under the front or rear of the vehicle for towing. These hooks are designed ONLY for transport tiedown. If the tiedown hooks are used for towing, the front or rear skirt and bumper will be damaged. IDENTIFICATION NUMBER LOCATIONS VEHICLE IDENTIFICATION NUMBER (VIN) ENGINE MODEL AND NUMBER L i Gartner Banana

GENERAL SERVICE INFORMATION VEHICLE DIMENSIONS d Measurement I I Overall height mm (in) I Overall length mm (in) Overall width mm (in) 3,948 (155.4) 1,676 (65.9) WHEEL ALIGNMENT Front wheel alignment (Unloaded*) 2,266 (89.2) 1,410 (55.5) 1,428 (56.2) Wheelbase mm (in) Rear wheel alignment (Unloaded*) Tread Total toe-in Front mrn (in) Rear mm (in) mm (in) degree Camber angle I 0'24' f 30' 3 + 3 (0.12 f 0.12) 0°18' + 18' Maximum steering angle Inner Outer I 37'23' f 2O 32O32' f 2O Caster angle * Fuel tank full; radiator coolant and engine oil at specified levels; and spare tire, jack, and tools in designated positions. 4O4Y f 45' 1 1°20' 3 * 3 (0.12 f 0.12) 0'18' + 18' King pin angle Camber angle Total toe-in -0'43' f 30' mm (in) degree Gartner Banana

BODY DIMENSIONS V The front suspension is a MacPherson strut style. Adjustment of the front wheel alignment is limited to camber adjustment. The front wheel alignment is determined by accuracy of the body itself. Accurate measurement and dimensional accuracy based upon the body dimensions are required when repairs are made. EXPLANATION OF BODY DIMENSIONS PROJECTED DIMENSIONS Flat-plane dimensions are those dimensions as measured on a flat surface projected from certain designated standard points of the body. STRAIGHT-LINE DIMENSIONS (ACTUAL DIMENSIONS) w Actual dimensions are those dimensions actually measured in a straight line between two points. Note Before the work, adjust the body according to the standard measurements and check the fit with associating parts, then proceed with the work. Front fender installation nuts 7 I Projected dimensions (Flat-plane dimensions) Gartner Banana

CONSTRUCTION No. 0 Part Name Bumper bracket Hood (Bonnet) 1 8 / Front frame, upper rear Crossmember No. 1 Shroud panel assy Radiator bracket No. @ Dash side junction I @ / Front frame, rear Part Name Crossmember No. 2 @ @I @ Light lid Dash panel assy Seat bracket No. 3 gusset Front frame, upper front Dash panel assy I @ / Stabilizer bracket @ @I Cowl panel, front Instrument bracket Apron reinforcement Front wheel apron assy I @ I Front wheel apron panel Q Tie-down hook reinforcement Front floor side pan Tunnel side junction Front frame @ @ Front fender panel Torque box Gartner Banana

CONSTRUCTION No. @ I Rear deck panel @ @ - - 1 8 1 Quarter panel Part Name @ I Rear deck member Trunk lid Rear end panel I @ 1 Light housing No. Part Name @ Q @ I Tunnel gusset Seal plate Splash protector @ @ I @ I Rear fender panel Bulkhead panel Floor side panel Floor center pan 0 I Crossmember No. 4 @ @ I @ I Door body @ Q Rear fender gusset Rear fender rain rail Fuel filler lid Parking bracket Crossmember No. 3 8 1 Floor side plate @ @ I @ / Side sill, inner B @ @ I ~ut plate Rear fender, lower Trunk board bracket Tank floor pan assy Trunk floor assy 1 8 1 Side sill reinforcement Q @ 0 I Rear side frame Striker reinforcement Side sill, inner C I I I 1 8 ( Cowl side panel @ @ I Closing bracket I @ I Hinge pillar Floor side panel @ @ 8 1 Battery clamp bracket I @ I Side sill, inner Side sill, outer Bumper bracket Cap bracket @ I Corner junction 1 8 1 Front header, Q @ @ @ Side sill gusset Hinge pillar, outer Side panel, inner Wheel inner house @ @ @ Beltline reinforcement Front pillar, outer Front pillar, inner @ Front header, upper Gartner Banana

No. @ I @ I Light lid I I I I I Front wheel apron assy 1 Part Name Bumper bracket @I I Crossmember No. 1 1 8 1 Dash panel assy No. @ 0 @ @I I @ 1 Front wheel apron panel I Part Name Front frame, upper rear Apron reinforcement Dash panel assy Cowl panel front @ @ -1 .............. Both side rust-proof treated steel k!-1 .............. One side rust-proof treated steel (Reverse side only) @ @ @ Front frame rear Stabilizer bracket Front frame Front floor side pan Front frame, upper front @ 0 Front fender panel Torque box @ Shroud panel assy Gartner Banana