1994 MAZDA MX-5 brake

INDEX P ANTILOCK BRAKE SYSTEM (ABS) 1. Hydraulic unit 5. ABS sensor rotor (front) Removal / Installation ......... page P-53 Removal / Ins~ection / ................. Disassembly / Assembly ...... page P-54 Installation page P-59 2. ABS control unit 6. ABS wheel-speed sensor (rear) Removal I Installation ......... page P-55 Removal 1 Inspection I ................. 3. Relays Installation page P-60 Removal / Inspection / 7. ABS sensor rotor (rear) ......... ................. w Installation page P-56 Removal / Inspection page P-61 .................. 4. ABS wheel-speed sensor (front) Installation page P-62 Removal / Inspection / ................. Installation page P-58 Gartner Banana

OUTLINE OUTLINE SPECIFICATIONS Item TY ~e Specifications Suspended Pedal level ratio Maximum stroke mm (in) 4.1 : I 1 20 14.72) - -- TY ~e Bore mm (in) Pad dimensions (area x thickness) mm2 x mm {in2 x in) Tandem (with level sensor) 22.22 (0.875) -- - TY ~e Cylinder bore mm (in) Disc plate dimension (effective diame- ter x thickness) mm {in) Disc (ventilated) 51.1 (2.01) Pad dimensions (area x thickness) mm2 x mm (in2 x in) Cylinder bore mm {in) Disc plate dimensions (effective diameter x thickness) mm (in) Disc (solid) 31.75 (1.25) Size mm {in) Vacuum multiplier 21 4 (8) Proportioning bypass valve (PBV) FMVSS 11 6: DOT-3 Brake fluid Mechanical, two rear brakes Hand lever Parking brake TY Pe - Operation system Gartner Banana

BRAKE SYSTEM P BRAKE SYSTEM PREPARATION - SST Wrench, flare nut 49 0221 600C Expand tool, disc brake 49 8043 001 Adjust gauge 49 8043 004 Wrench, socket Gauge, oil pressure (Part of 49 U043 OAO) - 49 U043 006 Hose (Part of 49 U043 OAO) For removal and installation brake PIPS For installation of disc pads 49 F043 001 Adjust gauge For Adjustment of push rod clearance For adjustment of push rod clearance 49 0208 701 A Boot air out tool For adjustment of push rod clearance For inspection of brake fluid pressure For removal of piston seal 49 8043 003 Lock tool, turning For inspection of brake fluid pressure For adjustment of push rod clearance 49 U043 OAO Gauge set, oil pressure & - For inspection of brake fluid pressure 49 U043 005 Joint (Part of ,-, 49 U043 OAO) For inspection of brake fluid pressure Gartner Banana

BRAKE SYSTEM TROUBLESHOOTING GUIDE Problem Poor braking Brakes pull to one side Brakes do not release Pedal goes too far (Too much pedal stroke) Abnormal noise or vibra- tion durlng braking Possible cause Leakage of brake fluid Air in lines Worn pad Brake fluid, grease, oil, or water on pad Hardening of pad surface or poor contact Malfunction of disc brake piston Malfunction of master cylinder Malfunction of power brake unit Malfunction of check valve (vacuum hose) Damaged vacuum hose Deterioration of flexible hose Malfunction of proportioning bypass valve (PBV) Worn pad Brake fluid, grease, oil, or water on pad Hardening of pad surface or poor contact Abnormal wear, distortion, or eccentricity of disc Malfunction of automatic adjuster in rear brake Looseness or deformation of dust cover mounting bolt Malfunction of disc brake piston Worn or improperly adjusted wheel bearing preload lmproper adjustment of wheel alignment Unequal tire air pressure No brake pedal play lmproper adjustment of push rod clearance Clogged master cylinder return port Pad not returning properly lmproper return of malfunction of brake caliper piston Excessive runout of disc plate lmproper adjustment of wheel bearing preload Air in system because of insufficient brake fluid lmproper adjustment of pedal play Worn pad Air in lines Worn pad Deterioration of pads Brakes do not release Foreign material or scratches on disc plate contact surface Looseness of caliper mounting bolt(s) Damage or deviation of disc contact surface Poor contact of pads Insufficient grease on sliding parts Action Repair Air bleed Replace Clean or replace Grind or replace Replace Repair or replace Repair or replace Repair or replace Replace Replace Replace Replace Clean or replace Grind or replace Repair or replace Repair Tighten or replace Repair or replace Replace or adjust Adjust Adjust Adjust Adjust Clean Repair Replace Replace Adjust or replace Add fluid and bleed air Adjust Replace Bleed air Replace Grind or replace Repair Clean Tighten Replace Repair or replace Apply grease Page - P- 7 P-25,29 P-25,29 P-25,29 P-28,32 P-11, 14 P-22 P-22 P-22 P- 7 P-23,24 P-25,29 P-25,29 P-25,29 section M - section M P-28,32 section M section R section Q P- 9 P-l2,15 - - P-28,32 section M section M P- 7 P- 9 P-25,29 P- 7 P-25,29 P-25,29 - - P-26,30 section M P-25,29 - 15UOPX-00 Gartner Banana

BRAKE SYSTEM P MIRROR AIR BLEEDING The brakes should be bleed whenever a brake line is dis- connected. If a hydraulic line is disconnected at the mas- ter cylinder, start at the slave cylinder farthest from the brake master cylinder, and move to the next closest slave cylinder until all four cylinders have been bled. If the disconnection point is anywhere except the master cylinder, start at the point closest to the disconnection, and move to the next farthest slave cylinder until all four cylinders have been bled. 1. On level ground jack up the vehicle and support it evenly on safety stands. 2. Remove the bleeder cap and attach a vinyl tube to the bleeder screw. 3. Place the other end of the vinyl tube in a clear container. 4. One person should depress the brake pedal a few times, and then hold it in the depressed position. 5. A second person should loosen the bleeder screw, drain out the fluid, and close the screw by using the SST. 6. Repeat steps 4 and 5 until only clean fluid is seen. The reservoir should be kept about 3/4 full during bleeding to prevent air from reentering the lines. 7. Modify the brake pipe tightening torque to allow for a torque wrench-SST combination. (Refer to section GI) "Torque Formulas". 8. Tighten the brake pipe by using SST. 9. Check for correct brake operation. 10. Verify that there is no fluid leakage. Clean away any spilled fluid with rags. 11. After bleeding the air, add brake fluid to the reservoir up to the specified level. BRAKE HYDRAULIC LINE On-vehicle Inspection Check the following and replace parts as necessary. 1. Cracks, damage, and corrosion of the brake hose 2. Damage to the brake hose threads 3. Scars, cracks, and swelling of the flexible hose 4. All lines for fluid leakage Gartner Banana

P BRAKE SYSTEM Removal / Installation 1. When disconnecting the flexible hose and brake line, remove the clip after loosening the flare nut by using the SST. > 2. When connecting the flexible hose, do not over tighten or twist it. 3. Verify that the hose does not contact other parts when the vehicle bounces or when the steering wheel is turned all the way to the left or right. 4. Modify the brake pipe tightening torque to allow for a torque wrench-SST combination. (Refer to section GI) "Torque Formulas". 5. Tighten the flare nut by using the SST. Tightening torque: 13-22 N.m (1 3-2.2 kgf-m, %&-I 6 ft-lbf} 6. Bleed the air from the brake system. BRAKE FLUID Inspection Check the fluid level in the reservoir. It should be between MAX and MIN. If the fluid level is extremely low, check the brake system for leaks. J Fluid specification: FMVSS 11 6: DOT-3 Replacement 1. Follow the procedure outlined in Air Bleeding. (Refer to page P-7.) 2. Continuity air bleeding and replacing the brake fluid until only clean fluid is seen. 3. Fill the reservoir to MAX. Gartner Banana

BRAKE SYSTEM P CLEARANCE BRAKE PEDAL On-vehicle Inspection Pedal height Verify that the distance from the center of the upper surface of the pedal pad to the carpet is as specified. Pedal height: l7l-l8l mm (6.93-7.13 in} (With carpet) Adjustment 1. Disconnect the stoplight switch connector. 2. Loosen locknut@ and turn switch @ until it does not con- tact the pedal. 3. Loosen locknuts @I and turn rod 0 to adjust the height. 4. Adjust the pedal free play and tighten operating rod lock- nuts @I. 5. Turn the stoplight switch until it contacts the pedal; then turn an additional 1 /2 turn. Tighten the locknuts. Tightening torque: 14--18 N.m (1.4--1.8 kgf-m, 10-13 ft-lbf) 6. Connect the stoplight switch connector. 7. Verify that the stoplight operates correctly. Pedal play 1. Depress the pedal a few times to eliminate the vacuum in the system. 2. Lightly depress the pedal by hand until resistance is felt, and check the free play. Free play: 4--7mm (0.16-4.28 in) Adjustment 1. Loosen locknuts @I and turn rod to adjust the free play. 2. Check the pedal height and verify that the stoplight switch operates correctly. Tightening torque: 24--34 N.m (2.4--3.5 kgf-m, 17-25 ft-lbf} Pedal-to-floor clearance 1. Verify that the distance from the floor panel to the center of the upper surface of the pedal pad is as specified when the pedal is depressed with a force of 589 N (60 kgf, 132 Ibf}. Pedal-to-floor clearance: 95mm (3.74 in} (Without carpet) 2. If the distance is less than specified, inspect for air in the brake system. Gartner Banana

P BRAKE SYSTEM Removal l Inspection / Installation 1. Remove in the order shown in the figure. 2. lnspect all parts and repair or replace as necessary. 3. Install in the reverse order of removal. 4. After installation, check and adjust the pedal height and free play if necessary. 1. Spring clip 2. Clevis pin 3. Nut 4. Spring washer 5. Bolt 6. Return spring lnspect for weakness and damage 7. Brake pedal lnspect for bending I BUOPX-OI 8. Guide pipe 9. Bushing lnspect for wear 10. Stopper lnspect for wear 11. Pedal pad lnspect for wear and damage Gartner Banana