1994 Lexus LS400 change

COMFORT ADJUSTMENT
52Releasing the switch will stop the seat cushion in that position.
Adjusting lumbar support
Push the control switch on either side.
The amount of lumbar support will change as long as the
switch is pushed.
HEADRESTS
Front seats (manual type)
Unlock
To raise the headrest, pull it up. To lower it, press the lock
release button and push the headrest down. To move the
headrest forward, pull on the top.
Pulling the top of the headrest forward as far as it can go will
return it to the upright position.
The headrest is most effective when it is close to your head.
Therefore, using a cushion on the seatback is not
recommended.
CAUTION:

Adjust the top of the headrest so that it is closest to the
top of your ears.

After adjusting the headrest, make sure it is locked in
position.

Do not drive with the headrests removed.

COMFORT ADJUSTMENT
71
NOTICE:
Do not perform any of the following changes without
consulting your Lexus dealer. Such changes can
interfere with proper operation of the SRS in some
cases.

Installation of electronic items such as a mobile
two-way radio or cassette tape player.

Modifications to the suspension system.

Repairs made on or near the front fenders, front
console, steering column, steering wheel or
instrument panel near front passenger airbag or seat
belt assembly.
This SRS has a warning light to indicate operating problems.
If either of the following conditions occurs, this indicates a
malfunction of the airbags and / or seat belt pretensioners.
Even if the seat belt pretensioners should fail, the seat belt will
operate conventionally. Contact your Lexus dealer as soon as
possible to service the vehicle.

The light does not come on when the ignition key is turned
to the “ACC” or “ON” position, or remains on.

The light comes on while driving.

COMFORT ADJUSTMENT
81
DRIVING POSITION MEMORY
SYSTEM
The micro computer can memorize the position of the driver’s
seat, the height of the shoulder belt anchor of the driver’s seat
belt, and the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position profiles
can be entered into the computer’s memory.
Recording a driving position in the computer’s memory can
only be done when the ignition key is in the “ON” position and
the shift lever is in the “P” position.
Setting a driving position
1. Adjust the driver’s seat, driver’s shoulder belt anchor,
tilt and telescopic steering and outside rear view mirrors
to the desired position.2. While pushing the “SET” button, push button “1” or “2”
until the signal beeps.
The beep sound means that the positions are recorded in the
computer’s memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.

COMFORT ADJUSTMENT
82
Activating a memorized position
When you push button “1” or “2”, the driving position will
be automatically adjusted to the position recorded for that
button.
Conditions for memorized position activation

Ignition key “ON” and shift lever in “P” position
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat
position will not change.

Key not in ignition switch and within 30 seconds of opening
driver’s door.
The memorized position can be activated, except for the tilt
and telescopic steering. This will be activated when the key
is inserted into the ignition switch.If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1” or “2”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s
memory will be erased and the memorized positions will have
to be set again.
CAUTION:

Do not start the vehicle while the adjustments are being
made.

Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body against
the steering wheel. If this happens, you can stop the
movement by pressing another driving position
memory switch, or depressing the brake pedal.