1994 Lexus LS400 seat memory

SECTION 1 – 6
49
INSTRUMENTS AND CONTROLS
Comfort adjustment
Front seat50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headrests52 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tilt and telescopic steering wheel54 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outside rear view mirrors57 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inside rear view mirror58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat belts59 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental restraint system (SRS)67 . . . . . . . . . . . . . . . . . . . . . . . .
Child restraint73 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driving position memory system81 . . . . . . . . . . . . . . . . . . . . . . . . . . . .

COMFORT ADJUSTMENT
81
DRIVING POSITION MEMORY
SYSTEM
The micro computer can memorize the position of the driver’s
seat, the height of the shoulder belt anchor of the driver’s seat
belt, and the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position profiles
can be entered into the computer’s memory.
Recording a driving position in the computer’s memory can
only be done when the ignition key is in the “ON” position and
the shift lever is in the “P” position.
Setting a driving position
1. Adjust the driver’s seat, driver’s shoulder belt anchor,
tilt and telescopic steering and outside rear view mirrors
to the desired position.2. While pushing the “SET” button, push button “1” or “2”
until the signal beeps.
The beep sound means that the positions are recorded in the
computer’s memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.

COMFORT ADJUSTMENT
82
Activating a memorized position
When you push button “1” or “2”, the driving position will
be automatically adjusted to the position recorded for that
button.
Conditions for memorized position activation

Ignition key “ON” and shift lever in “P” position
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat
position will not change.

Key not in ignition switch and within 30 seconds of opening
driver’s door.
The memorized position can be activated, except for the tilt
and telescopic steering. This will be activated when the key
is inserted into the ignition switch.If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1” or “2”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s
memory will be erased and the memorized positions will have
to be set again.
CAUTION:

Do not start the vehicle while the adjustments are being
made.

Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body against
the steering wheel. If this happens, you can stop the
movement by pressing another driving position
memory switch, or depressing the brake pedal.