1994 Lexus ES300 engine

STARTING AND DRIVING
Brake pedal
”D” (Drive)
position
Parking brake
lever
111
On
Off
Indicator light
4. Set the overdrive switch to the ON position.
Always set the overdrive switch to the ON position for improved
fuel economy and quiet driving. (See “(b) Using engine
braking” and “(f) Good driving practice” for exceptions.)
5. With your foot holding down the brake pedal, shift the
selector lever to “D”.CAUTION:
Never put your foot on the accelerator pedal while
shifting.
6. Release the parking brake and brake pedal. Depress the
accelerator pedal slowly for smooth starting.
The vehicle will start in the first gear and automatically shift to
the most suitable gear for the running conditions, such as the
vehicle speed, hill climbing, hard towing, etc. However, while
the engine coolant temperature is low and the vehicle is
traveling at low speed, the transmission will not shift into the
overdrive gear even with the overdrive switch on.
In “D” position, the automatic transmission system will select
the most suitable gear for the running conditions such as hill
climbing, hard towing, etc.
If you need to accelerate rapidly while driving, push the
accelerator pedal all the way to the floor. The transmission will
automatically downshift to the third, second or first gear,
according to the vehicle speed.
If engine braking is needed, such as in descending a long hill,
see “(b) Using engine braking”.

STARTING AND DRIVING
Overdrive switch
:Shifting
”D” (Drive) position
”2” (Second) position
”L” (Low) position
11 2
(b) Using engine braking
To use the braking power of the engine, downshift the
transmission in the way described below:

Turn off the overdrive switch. (This is effective only when
you are driving in the “D” position.) The “O / D OFF” indicator
light in the instrument cluster will come on and the
transmission will downshift to the third gear.

Shift into the “2” position. The transmission will downshift to
the second gear when the vehicle speed is 128 km / h (80
mph) or lower and more powerful engine braking will be
obtained.

Shift into the “L” position. The transmission will downshift to
the first gear when the vehicle speed is 70 km / h (43 mph)
or lower and maximum engine braking will be applied.CAUTION:
Be careful when downshifting on a slippery surface. The
abrupt change in engine speed could cause the vehicle to
spin or skid.
(c) Using the “2” and “L” positions
The “2” and “L” positions are used for strong engine braking as
described previously.
With the selector lever in “2” or “L”, you can start the vehicle in
motion as with the lever in “D”.
With the selector lever in “2”, the vehicle will start in the first
gear and automatically shift to the second gear.
With the selector lever in “L”, the transmission is engaged in
the first gear.
NOTICE:

Be careful not to overrev the engine. Watch the
tachometer to keep engine rpm from going into the
red zone. The approximate maximum allowable
speed for each position is given below for your
reference:

“2” ... 128 km / h (80 mph)
“L” ... 70 km / h (43 mph)

Do not continue hill climbing or hard towing for a long
time in the “2” or “L” position. This may cause severe
automatic transmission damage from overheating. To
prevent such damage, “D” position should be used in
hill climbing or hard towing.

STARTING AND DRIVING
11 4
(f) Good driving practice

If the transmission repeatedly upshifts and downshifts
between the third and overdrive gears when climbing a
gentle slope, turn off the overdrive switch. Be sure to turn the
switch on immediately after climbing the slope.

When towing a trailer, in order to maintain efficient engine
braking and electrical charging performance, do not use
overdrive.
CAUTION:
Always keep your foot on the brake pedal while stopped
with the engine running. This prevents the vehicle from
creeping.
NOTICE:
Do not hold the vehicle on an upgrade with the
accelerator pedal. This can cause the transmission to
overheat. Always use the brake pedal or parking brake.
(g) If you cannot shift the selector lever out
of “P” position
If you cannot shift the selector lever from “P” position even
though the brake pedal is depressed, use the shift lock
override button. For instructions, see “If you cannot shill the
automatic transmission selector lever” on page 143.
(h) If the “O / D OFF” indicator light flashes
If the “O / D OFF” indicator light flashes, contact your Lexus
dealer as soon as possible. There may be trouble in the
transmission system.
CRUISE CONTROL
The cruise control allows you to cruise the vehicle at a
desired speed over 40 km / h (25 mph) with your foot off the
accelerator pedal.
Your cruising speed can be maintained although a slight speed
change may occur when driving up or down a gradient, within
the limits of engine performance. On steeper hills, a greater
speed change will occur so it is better to drive without the cruise
control.
When the cruise control is on, the driving pattern of the
automatic transmission is fixed in the normal position,
regardless of the position of the selector switch.
CAUTION:

To help maintain maximum control of your vehicle, do
not use the cruise control when driving in heavy or
varying traffic, or on slippery (rainy, icy or
snow-covered) or winding roads.

Avoid vehicle speed increases when driving downhill.
Use engine braking by downshifting the transmission.

STARTING AND DRIVING
11 7
BRAKE SYSTEM
The tandem master cylinder brake system is a hydraulic
system with two separate sub-systems. If either sub-system
should fail, the other will still work. However, the pedal will be
harder to press, and your stopping distance will be longer.
Also, the brake system warning light may come on.
CAUTION:
Do not rely on a single brake system. Have your brakes
fixed immediately.
Brake booster
The brake booster uses engine vacuum to power-assist the
brakes. If the engine should quit while you are driving, you can
bring the vehicle to a stop with normal pedal pressure. There
is enough reserve vacuum for one or two stops but no more!
CAUTION:

Do not pump the brake pedal if the engine stalls. Each
push on the pedal uses up your vacuum reserve.

Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal
hard-much harder than normal. And your braking
distance will be longer.
Anti-lock brake system
The anti-lock brake system is designed to prevent lock-up
of the wheels during sudden braking or braking on
slippery surfaces. This helps the vehicle remain steerable
and stable under these circumstances.
The system functions with normal pedal operation. When the
anti-lock function is in action, pulsation of the brake pedal may
result, together with a characteristic noise. This indicates that
the system is functioning properly.
The anti-lock brake system comes into operation when the
vehicle is accelerating and the vehicle speed reaches
approximately 10 km / h (6 mph). It stops operating when the
vehicle is decelerating and the vehicle speed falls below
approximately 5 km / h (3 mph).
You may hear a sound in the engine compartment for a few
seconds just after the vehicle is started. This means that the
anti-lock brake system is in the self-check mode, and does not
indicate a malfunction.
Even though the anti-lock brake system is in operation, full
stability of the vehicle cannot be maintained for certain slippery
road conditions or high speed driving when cornering. Even
with the anti-lock brake system installed, it is still important to
drive with all due care.