1994 Lexus ES300 buttons

AIR CONDITIONING AND AUDIO
82The automatic air conditioning automatically maintains the set
temperature.
This air conditioning features automatic fan speed and air flow
control which automatically selects the most suitable fan
speed and air flow to control the temperature. The ignition key
must be in the “ON” position.
You may use manual controls to override the automatic
settings.
(a) Climate control
SETTING OPERATION − automatic control
1. Push the “AUTO
.TEMP” knob.
Air flow quantity, switching of the diffusers, on-off of the air
conditioning, and switching of the air intake between
RECIRCULATED AIR and OUTSIDE AIR are automatically
adjusted. The operation status is shown by each indicator.
When one of the manual control buttons is depressed while
operating in automatic mode, the operation corresponding to
the button depressed is set. Other conditions continue to be
adjusted automatically.
2. Turn the “AUTO
.TEMP” knob until the desired
temperature is displayed.
The “AUTO
.TEMP” knob is used to set the desired passenger
compartment temperature. The temperature of air delivered to
the passenger compartment will be controlled automatically
according to the setting. The figures on the panel indicate
degrees Fahrenheit or Centigrade.SETTING OPERATION − manual control
If manual air flow selection is desired −
The outlets from which air is delivered can be selected
manually by pushing either side of the air flow control
(MODE) button. The mode appears on the display. The
function of each mode is as follows:
FACE mode − Directs air flow at face level.
BI-LEVEL mode − Directs air flow at face level, and at
floor level for both front and rear. Except in ventilation, the air
to the floor is slightly warmer than air to the face.
FLOOR mode − Directs air flow mostly at floor level for
both front and rear.
FLOOR / WINDSHIELD mode − Directs air flow to the
windshield and front side windows as well as floor level for both
front and rear.
FRONT WINDSHIELD mode − Directs air flow mostly to
the windshield and front side windows.
When this mode is selected while operating in automatic
mode, the air conditioning is set to operate and the OUTSIDE
AIR mode is set.
If you push the “FRONT WINDSHIELD” button once again
while in the FRONT WINDSHIELD mode, the mode then
returns to the last mode used.

AIR CONDITIONING AND AUDIO
Without compact disc player
“PWR. VOL” knob
(For turning radio on
and adjusting volume)“AM” button
(For turning radio on
and selecting AM)“FM1” button
(For turning radio on
and selecting FM)“FM2” button
(For turning radio on
and selecting FM)
Radio display
Station selector
buttons (1-6)
“FADER” knob
(For front and rear
sound balance)
“BALANCE” knob
(For right and left
sound balance)“TREBLE” knob
(For treble control)“MID” knob
(For mid range control)
“BASS” knob
(For bass control)
“TUNE SEEK” button
(For frequency tuning)
“SCAN” button
(For preset scan tuning
and scan tuning)
86
Radio operation

AIR CONDITIONING AND AUDIO
With compact disc player
“PWR. VOL” knob
(For turning radio on
and adjusting volume)
“AM” button
(For turning radio on
and selecting AM)
“FM1 / 2” button
(For turning radio on
and selecting FM)
Radio display
Station selector
buttons (1-6)
“FADER” knob
(For front and rear
sound balance)“BALANCE” knob
(For right and left
sound balance)“TREBLE” knob
(For treble control)“MID” knob
(For mid range control)“BASS” knob
(For bass control)
“TUNE SEEK” button
(For frequency tuning)
“SCAN” button
(For preset scan tuning
and scan tuning)
87

AIR CONDITIONING AND AUDIO
89 Push the
(SCAN) button for longer than 2 seconds. With
“SCAN” on the display, the radio will automatically seek out a
station of higher frequency, hold it for 5 seconds and scan to
the next. To continue listening to the broadcast of your choice,
simply push the
(SCAN) button once again.
Manual tuning: Push the
(TUNE) button within 0.5 seconds.
Each time you push the button, the radio will step up or down
to another frequency where stations could exist.
(c) Presetting a station
1. Tune in the desired station. (See “(b) Selecting a station”.)
2. Push one of the station selector buttons and hold it until a
beep is heard. This sets the station to the button and the button
number will appear on the display.
Each button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station will be cancelled when the power source is
severed (battery disconnected, burnt fuse, etc.).(d) Adjusting the tone
To adjust the low-pitched tone, push the “BASS” knob (if
depressed) and turn it.
To adjust the middle-pitched tone, push the “MID” knob (if
depressed) and turn it.
To adjust the high-pitched tone, push the “TREBLE” knob (if
depressed) and turn it.
(e) Adjusting the sound balance
To balance the sound between the right and left speakers,
push the “BALANCE” knob (if depressed) and turn it.
To balance the sound between the front and rear speakers,
push the “FADER” knob (if depressed) and turn it.
Radio operating tips
The antenna automatically extends to full height when the
radio and ignition are turned on and retracts when either is
turned off.
CAUTION:
Before extending the antenna, confirm that no one is close
enough to get injured.
NOTICE:
To prevent damage to the antenna, make sure it is
retracted before running your vehicle through an
automatic car wash.

AIR CONDITIONING AND AUDIO
99 (d) Selecting a program
Automatic program selection: Use for direct access to a
desired program.
Push the
(TRACK) button on either side and hold it
until the desired program number appears on the display. As
you release the button, the player will start playing the selected
program from the beginning.
Manual program selection:
Push either of the
(FAST) buttons and hold it to fast
forward or reverse the disc: Releasing the button starts the
play from that position.
Disc scan selection: Use for disc-to-disc scanning.
Push the
(SCAN) button. With “SCAN” on the display, the
program at the beginning of each disc will be played for 10
seconds. To continue listening to the program of your choice,
push the
(CD) or (SCAN) button.
(e) Other compact disc player functions
“RPT” button: Use for automatic repeat of the program
currently being listened to.
Push the
(RPT) button on the left side while the
program is being played. As this is done, “RPT” will appear on
the display. When the program is finished, the disc will
automatically go back to the beginning of the program and the
program will be played again. To cancel it, push the button
once again.“RANDOM” button: Use for automatic program selection and
play the system.
Where the
(RANDOM) button is pushed on the right
side, “RND” appears on the display and the system selects a
program on the disc which is set and plays it. To cancel it, push
the button once again.
When a program is skipped or the system is inoperative, push
the
(CD) button to reset.
“CD CMP” button: Use for listening to music in noisy
situations.
Push the
(CD CMP) button and hold it until a beep is
heard “CMP” appears on the display. Small sounds are
emphasized and large sounds muted slightly so that every
sound can be heard clearly.
This function works only in the “CD” mode. To cancel it, push
the button once again and hold it until a beep is heard.
(f) If the player malfunctions
If “WAIT” appears on the display, audio signals of the disc
cannot be read or the system has trouble. Push the
(CD)
button once again.
If the player does not operate, check that the disc surface is not
soiled or damaged. If the disc is O.K., the following two causes
are possible.
Condensation may have occurred on the internal
mechanism of the player.
Open the trunk to let air circulate.