1994 JEEP CHEROKEE oil filter

WARNING: LARGE AMOUNTS OF REFRIGERANT
RELEASED IN A CLOSED WORK AREA WILL DIS-
PLACE THE OXYGEN AND CAUSE SUFFOCATION.
ALWAYS MAINTAIN GOOD VENTILATION SUR-
ROUNDING THE WORK AREA.
R-12 gas, under normal conditions, is non-poison-
ous.
WARNING: THE DISCHARGE OF R-12 GAS NEAR
AN OPEN FLAME CAN PRODUCE A VERY POISON-
OUS GAS CALLED PHOSGENE. PHOSGENE IS
GENERATED WHEN A FLAME-TYPE LEAK DETEC-
TOR IS USED.
CAUTION: When charging an A/C system always
keep the tank in an upright position. If the tank is
on its side or upside down, liquid refrigerant will
enter the system and may damage the compressor.
In most instances when charging or adding refrig-
erant, moderate heat is required to bring the pres-
sure of the refrigerant above the pressure of the
system. A bucket or large pan of hot water, not over
52ÉC (125ÉF), is all the heat required for this pur-
pose. DO NOT heat the refrigerant container with a
blow torch or any other means that would raise the
temperature and pressure above this temperature.
CAUTION: DO NOT allow liquid refrigerant to touch
bright metal. Refrigerant will tarnish bright metal
and chrome surfaces. Refrigerant in combination
with moisture is very corrosive and can cause ex-
tensive damage to all metal surfaces.
Avoid splashing the refrigerant on any surface.
RECYCLING
(R-12) refrigerant is a chloroflorocarbon (CFC) that
can contribute to the depletion of the ozone layer in
the upper atmosphere. Ozone filters out harmful ra-
diation from the sun. To assist in protecting the
ozone layer, Chrysler Corporation requires that an
(R-12) refrigerant recovery device that meets SAE
standard J1991 be used. Contact an automotive ser-
vice equipment supplier for refrigerant recycling
equipment that is available in your area. Refer to
the operating instructions provided with the recy-
cling equipment for proper operation.
SERVICE PRECAUTIONS
Never open or loosen a connection before discharg-
ing the system refrigerant.
A system which has been opened to replace a com-
ponent or one which has discharged through leakage
must be evacuated before charging.
Immediately after disconnecting a component from
the system, seal the open fittings with a cap or plug.Before disconnecting a component from the system,
clean the outside of the fittings thoroughly.
DO NOT remove the sealing caps from a replace-
ment component until ready to install.
Refrigerant oil will absorb moisture from the atmo-
sphere if left uncapped. DO NOT open an oil con-
tainer until ready to use and install the cap
immediately after using. Store the oil only in a clean
moisture-free container.
Before connecting an open fitting always install a
new seal ring. Coat the fitting and seal with clean
refrigerant oil before connecting.
When installing a refrigerant line avoid sharp
bends. Position the line away from the exhaust or
any sharp edges which may chafe the line.
Tighten fittings only to the specified torque. The
copper and aluminum fittings used in the A/C system
will not tolerate over tightening.
When disconnecting a fitting use a wrench on both
halves of the fitting to prevent twisting of the refrig-
erant lines or tubes.
DO NOT open a refrigerant system or uncap a re-
placement component unless it is as close as possible
to room temperature. This will prevent condensation
from forming inside of a component which is cooler
than the surrounding air.
Keep service tools and the work area clean. Con-
tamination of A/C system through careless work hab-
its must be avoided.
PRESSURE GAUGE AND MANIFOLD ASSEMBLY
Pressure Gauge and Manifold Assembly Tool
C-3740-B (Fig. 1) is the most important tool used to
service the air conditioning system. The gauge as-
sembly is used to determine:
²System high side gauge pressures
²System low side gauge pressures
²The correct refrigerant charge
²System diagnosis
It is designed to provide simultaneous high and low
side pressure indications, because these pressures
must be compared to determine the correct system
operation.
LOW SIDE GAUGE
The low side gauge is a compound gauge, which
means that it will register both pressure and vacuum
(Fig. 1). The compound gauge is calibrated 0-1034
kPa (0-150 psi) pressure and 0-760 mm (0-30 in.) of
mercury vacuum. It is connected to the suction ser-
vice valve to check the low side pressure or vacuum.
HIGH SIDE GAUGE
The high side gauge is used to check the pressure
in the discharge side of the air conditioning system
(Fig. 1).
24 - 2 HEATING AND AIR CONDITIONINGJ

AIR CONDITIONING
CONTENTS
page page
AIR CONDITIONING EQUIPMENT........... 4
AIR CONDITIONING PERFORMANCE TESTS . . 5
GENERAL INFORMATION.................. 1
REFRIGERANT LEAK TESTING, DISCHARGING,
EVACUATING AND CHARGING............ 8REFRIGERANT OIL....................... 9
SERVICE PRECAUTIONS.................. 3
WARNINGS AND CAUTIONS FOR R134A
SYSTEM.............................. 3
GENERAL INFORMATION
A/C COMPONENTS
COMPRESSORÐThe SD-709 Compressor is used
on all models. The compressor compresses the low-
pressure refrigerant vapor from the evaporator into a
high pressure, high temperature vapor. The compres-
sor is serviced as an assembly only.
CLUTCH PULLEY AND COILÐThey are
mounted on the compressor and providing a way to
drive the compressor. The compressor clutch and coil
are the only serviced parts on the SD-709 compres-
sor. When the compressor is not in operation, the
pulley free wheels on the clutch hub bearing. When
the coil is energized the clutch plate is magnetically
engaged with the pulley and turns the compressor
shaft.
CONDENSERÐThe condenser is located in front
of the engine radiator. Its function is to cool the hot
high pressure refrigerant gas. This causes it to con-
dense into high pressure liquid refrigerant.
FILTER-DRIERÐThe drier is used to remove con-
taminates and traces of moisture from the refriger-
ant system.
SIGHT-GLASSÐThe sight glass is located on top
of the filter drier. It is used as a diagnostic tool to ob-
serve refrigerant flow.
LOW-PRESSURE HIGH-PRESSURE CUT-OFF
SWITCHÐThe switch is located on the filter drier
and is wired in series with compressor clutch. When
the pressure drops down to 193 kPa (28 psi) the
switch interrupts the power to the compressor clutch.
When the pressure increases above 3100 to 3375 kPa
(450 to 490 psi) the switch interrupts the power to
the compressor clutch.
HIGH PRESSURE RELIEF VALVEÐThe valve
is located on the filter drier. The valve is used to pre-
vent excessive pressure up build of 3445 to 4135
kPag (500 to 600 psi) and above. This will prevent
damage to the compressor and other system compo-
nents.EXPANSION VALVEÐThe expansion valve is lo-
cated in the engine compartment on XJ vehicles. On
YJ vehicles it is located behind the A/C housing. Its
function is to meter refrigerant into the evaporator in
accordance with cooling requirements.
EVAPORATOR COILÐThe coil is located in the
A/C housing. Its function is to remove heat and de-
humidify the air before it enters the vehicle.
FIN SENSING CYCLING CLUTCH SWITCHÐ
The switch is attached to the evaporator coil. This
switch prevents condensate water on the evaporator
coil from freezing. It does this by cycling the com-
pressor clutch on and off. This switch is used onXJ
only
THERMOSTATÐThe thermostat is located in the
evaporator housing. Its function is to cycle the com-
pressor clutch to control temperature. The thermo-
stat is used on theYJonly.
REFRIGERANT LINESÐThe lines are used to
carry the refrigerant between the various system
components.
SERVICE PORTSÐThe high pressure service
port is located on the discharge line near the com-
pressor. The low pressure service port is located on
the suction line near the compressor. The compressor
no longer uses service valves.
After servicing the refrigerant system, always in-
stall service port caps.
REFRIGERANT
The vehicles use a new type of refrigerant called
R-134a. It is a non-toxic, non-flammable, clear color-
less liquified gas.
R-134a refrigerant is not compatible with R-12 re-
frigerant in an air conditioning system. A small
amount of R-12 in a R-134a system will cause com-
pressor failure, refrigerant oil sludge or poor A/C per-
formance.
JAIR CONDITIONING1

CARPET/FLOOR MATS.................23-198
CARPET/MATÐXJ VEHICLES, FRONT.....23-129
CARPET/MATÐXJ VEHICLES, REAR......23-130
CARPETS AND FLOOR MATS............23-129
CARRIER, EXTERNAL SPARE/WHEEL
TIRE..............................23-172
CASE ASSEMBLY, TRANSFER......21-282,21-306
CASE CLEANING AND INSPECTION,
TRANSMISSION.....................21-118
CASE COVER OIL SEAL REPLACEMENT,
TIMING.........................9-26,9-67
CASE COVER, TIMING...............9-27,9-67
CASE DISASSEMBLY AND OVERHAUL,
TRANSFER...................21-277,21-297
CASE FILL LEVEL, TRANSFER...........21-294
CASE IDENTIFICATION, ENGINE AND
TRANSMISSION/TRANSFER..........INTRO.-3
CASE IDENTIFICATION, TRANSFER . 21-273,21-293
CASE INSTALLATION, TRANSFER . . . 21-276,21-296
CASE, LEGEND FOR NP231 TRANSFER....21-292
CASE, LEGEND FOR NP242 TRANSFER....21-319
CASE LUBRICANT, TRANSFER.....21-273,21-294
CASE, NP231 TRANSFER.........21-272,21-291
CASE, NP242 TRANSFER...............21-293
CASE OVERHAUL, FIRST-REVERSE
BRAKE PISTON AND TRANSMISSION....21-237
CASE REMOVAL, TRANSFER......21-276,21-296
CASE SPECIFICATIONS, TRANSMISSION/
TRANSFER.........................21-320
CASE, TRANSFER.......................0-25
CATALYTIC CONVERTER..............11-1,11-5
CATALYTIC CONVERTER/MUFFLER/
TAILPIPE SUPPORT BRACKETS.........23-85
CAUSES, CLUTCH PROBLEM...............6-3
CENTER HIGH MOUNTED STOP LAMP
(CHMSL)ÐXJ.......................8L-10
CENTER HIGH MOUNTED STOP LAMP
(CHMSL)ÐYJ.......................8L-11
CERTIFICATION LABEL, VEHICLE SAFETY . INTRO.-1
CHAIN AND SPROCKETS, TIMING......9-28,9-68
CHANGE AND FILTER REPLACEMENT,
ENGINE OIL..........................0-15
CHANGE, LUBRICANT; FRONT
SUSPENSION AND AXLE................2-22
CHANGE, LUBRICANT; REAR SUSPENSION
AND AXLES......................3-13,3-30
CHARGE RATE.........................8A-6
CHARGE, SYSTEM......................24-5
CHARGING, BATTERY....................8A-5
CHARGING TIME TABLE, BATTERY.........8A-5
CHASSIS AND BODY COMPONENTS........0-30
CHASSIS COMPONENT AND WHEEL
BEARING LUBRICANTS.................0-30
CHECK BALL DIMENSIONS, AW-4 VALVE
BODY.............................21-328
CHECK ENGINE LAMP FOR DIAGNOSTIC
TROUBLE CODES, INDICATOR..........8A-19
CHECK ENGINE, MALFUNCTION
INDICATOR LAMP; INSTRUMENT PANEL
AND GAUGESÐXJ................8E-2,8E-4
CHECK ENGINE, MALFUNCTION
INDICATOR LAMP; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-16
CHECK, PRELIMINARY BRAKE..............5-7
CHECK (ROAD TEST), OPERATIONAL.......8H-7
CHECK VALVE REPLACEMENT............19-33
CHECK VALVE TEST, POWER BOOSTER......5-11
CHECK WITH BATTERY INDICATOR
(BASE CLUSTER ONLY), OPERATIONAL . . . 8A-14
CHECK WITH VOLTMETER, OPERATIONAL . . . 8A-15
CHECKING FLUID LEVEL AND
CONDITION...................21-96,21-173
CHECKING FOR DIAGNOSTIC TROUBLE
CODE...............................8H-5
CHECKS FIRST, SYMPTOM AND ACTIONÐ
SEE PRELIMINARY.....................7-6
CHECKS, PRELIMINARY...................7-5
CHIP PROTECTION, STONE.............23-201
CHMSLÐXJ, CENTER HIGH MOUNTED
STOP LAMP.........................8L-10
CHMSLÐYJ, CENTER HIGH MOUNTED
STOP LAMP
.........................8L-11
CIRCUIT DIAGNOSIS, IGNITION
SECONDARY
........................8D-12
CIRCUIT IDENTIFICATION
................8W-2
CIRCUIT, PRINTED
.....................8E-22CIRCUIT REMOVAL, PRINTED............8E-24
CIRCUIT REPLACEMENT, PRINTED........8E-19
CIRCUIT REPLACEMENTÐINSTRUMENT
CLUSTER REMOVED, PRINTED...........8E-6
CIRCUIT SENSEÐPCM INPUT, IGNITION....14-21
CIRCUIT TESTS - (VOLTAGE DROP
METHOD), STARTER FEED..............8A-9
CIRCUIT TESTS, STARTER CONTROL......8A-11
CIRCUIT VOLTAGE, BATTERY OPEN.........8A-4
CIRCUIT VOLTAGE TEST, BATTERY OPEN....8A-3
CIRCUITS, ABS SYSTEM WIRING AND
ELECTRICAL..........................5-4
CLAMPS, FUEL TUBES/LINES/HOSES . . 14-9,14-56
CLASSIFICATION OF LUBRICANTS...........0-2
CLASSIFICATIONS AND RATINGS,
BATTERY............................8A-8
CLASSIFICATIONS AND RATINGSÐ
LEFT HAND DRIVE, BATTERY...........8B-10
CLASSIFICATIONS AND RATINGSÐ
RIGHT HAND DRIVE, BATTERY..........8B-10
CLEAN BRAKE FLUID, IMPORTANCE OF.....5-48
CLEANER, AIR.........................25-7
CLEANER FILTER ELEMENT, ENGINE AIR....0-16
CLEANER HOUSING, AIR; EMISSION
CONTROL SYSTEMS...................25-8
CLEANER HOUSING, AIR; FUEL SYSTEM....14-54
CLEANING AND INSPECTION . 21-13,21-204,21-305
CLEANING AND INSPECTION, CALIPER......5-28
CLEANING AND INSPECTION, GEAR.......19-40
CLEANING AND INSPECTION,
TRANSMISSION CASE................21-118
CLEANING OF TIRES....................22-2
CLEANING/INSPECTION; FRONT
SUSPENSION AND AXLE................2-35
CLEANING/INSPECTION; REAR
SUSPENSION AND AXLES...............3-18
CLEANING/REVERSE FLUSHING,
COOLING SYSTEM....................7-17
CLEARANCE, AW-4 BUSHING AND
PISTON...........................21-326
CLIMATE CONTROL SYSTEMÐXJ VEHICLES . 24-22
CLIMATE CONTROL SYSTEMÐYJ VEHICLES . 24-37
CLIP, FUEL AND BRAKE FLUID TUBE
RETAINER; BODY COMPONENTSÐXJ
VEHICLES..........................23-86
CLIP, FUEL AND BRAKE FLUID TUBE
RETAINER; FRAME AND BUMPERS.......13-16
CLUSTER AND GAUGE HOUSINGS,
INSTRUMENT......................23-190
CLUSTER BEZEL, INSTRUMENT.....23-91,23-191
CLUSTER BULB REPLACEMENT,
INSTRUMENT.......................8E-19
CLUSTER DIAGNOSIS, INSTRUMENT;
INSTRUMENT PANEL AND
GAUGESÐXJ.........................8E-3
CLUSTER DIAGNOSIS, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐYJ . . 8E-14
CLUSTER GAUGES, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐXJ . . 8E-13
CLUSTER GAUGES, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐYJ . . 8E-27
CLUSTER GENERAL INFORMATION,
INSTRUMENT; INSTRUMENT PANEL AND
GAUGESÐXJ.........................8E-1
CLUSTER GENERAL INFORMATION,
INSTRUMENT; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-14
CLUSTER, HIGH LINE...................8E-12
CLUSTER, INSTRUMENT................8E-15
CLUSTER, LOW LINE...................8E-11
CLUSTER REMOVED, GAUGE
REPLACEMENTÐINSTRUMENT..........8E-5
CLUSTER REMOVED, GEAR SELECTOR
INDICATOR REPLACEMENTÐ
INSTRUMENT........................8E-6
CLUSTER REMOVED, PRINTED CIRCUIT
REPLACEMENTÐINSTRUMENT..........8E-6
CLUSTER REMOVED, SPEEDOMETER
REPLACEMENTÐINSTRUMENT..........8E-5
CLUSTER REMOVED, TACHOMETER
REPLACEMENTÐINSTRUMENT
..........8E-5
CLUSTER REPLACEMENT, GAUGE
.........8E-24
CLUSTER REPLACEMENT, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐXJ
. . . 8E-5
CLUSTER REPLACEMENT, INSTRUMENT;
INSTRUMENT PANEL AND GAUGESÐYJ
. . 8E-17CLUSTER SERVICE PROCEDURES,
INSTRUMENT; INSTRUMENT PANEL AND
GAUGESÐXJ.........................8E-5
CLUSTER SERVICE PROCEDURES,
INSTRUMENT; INSTRUMENT PANEL AND
GAUGESÐYJ........................8E-17
CLUSTER/SWITCH/LIGHTER/RADIO/HEVAC,
INSTRUMENT.......................23-91
CLUSTERS, INSTRUMENT...............8E-10
CLUTCH AND BRAKE PACK
REQUIREMENTS, AW-4...............21-328
CLUTCH AND OUTPUT SHAFT
OVERHAUL, NO. 2 ONE-WAY..........21-234
CLUTCH COMPONENT LUBRICATION.........6-1
CLUTCH COMPONENTS
...................6-1
CLUTCH COVER AND DISC INSTALLATION
....6-10
CLUTCH COVER AND DISC REMOVAL
.......6-10
CLUTCH DIAGNOSIS
.....................6-3
CLUTCH DISC AND PLATE THICKNESS,
AW-4
.............................21-325
CLUTCH FLUID LEVEL
...................6-14
CLUTCH HOUSING REPLACEMENT
.........6-11
CLUTCH, HYDRAULIC
....................0-22
CLUTCH HYDRAULIC LINKAGE
INSTALLATION
........................6-12
CLUTCH HYDRAULIC LINKAGE REMOVAL
....6-11
CLUTCH INSPECTION, TORQUE
CONVERTER STATOR
................21-189
CLUTCH LINKAGE FLUID
..................6-1
CLUTCH, MAGNETIC
....................24-18
CLUTCH OPERATION
.....................6-2
CLUTCH OVERHAUL, DIRECT
............21-219
CLUTCH OVERHAUL, FORWARD
.........21-223
CLUTCH OVERHAUL, FRONT
............21-125
CLUTCH OVERHAUL, OVERDRIVE
PLANETARY GEAR
...................21-209
CLUTCH OVERHAUL, REAR
.............21-128
CLUTCH OVERHAUL, SUN GEAR AND
NO. 1ONE-WAY
.....................21-229
CLUTCH PEDAL INSTALLATION
............6-15
CLUTCH PEDAL REMOVAL
................6-15
CLUTCH PROBLEM CAUSES
...............6-3
CLUTCH RELAY, AIR CONDITIONING
.......14-54
CLUTCH RELAYÐPCM OUTPUT, AIR
CONDITIONING
......................14-24
CLUTCH RELAYÐPCM OUTPUT, TORQUE
CONVERTER
........................14-27
CLUTCH RELAY TEST, TORQUE
CONVERTER
........................14-45
CLUTCH RELAY, TORQUE CONVERTER
.....14-60
CLUTCH SAFETY PRECAUTIONS
...........6-10
CLUTCH SERVICE
.......................6-10
CLUTCHÐLOW-REVERSE DRUMÐREAR
SUPPORT OVERHAUL, OVERRUNNING
. . . 21-118
COAT, BASE/COLOR
...................23-201
CODE, CHECKING FOR DIAGNOSTIC
TROUBLE
...........................8H-5
CODE DECODING, VEHICLE
...........INTRO.-3
CODE (DTC), DIAGNOSTIC TROUBLE
.......14-51
CODE (DTC), GENERATOR DIAGNOSTIC
TROUBLE
...........................8A-19
CODE IDENTIFICATION, WIRE
.............8W-2
CODE LETTERS, JEEP BODY
...............5-2
CODE PLATE, VEHICLE
...............INTRO.-2
CODES AND DIMENSIONS,
DESIGNATIONS, LABELS/PLATES,
.....INTRO.-1
CODES, INDICATOR (CHECK ENGINE)
LAMP FOR DIAGNOSTIC TROUBLE
.......8A-19
CODES, VEHICLE DESIGNATION
........INTRO.-1
CODES, XJ EXTERIOR PAINT
............23-205
CODES, XJ INTERIOR PAINT
............23-205
CODES, YJ EXTERIOR PAINT
............23-206
CODES, YJ INTERIOR PAINT
............23-206
COIL, EVAPORATOR
....................24-34
COIL, IGNITION; FUEL SYSTEM
...........14-57
COIL, IGNITION; IGNITION SYSTEMS
. 8D-4,8D-11,
8D-26
COILÐPCM OUTPUT, IGNITION
...........14-26
COIL RESISTANCE, IGNITION
............8D-11
COIL SPRING
..........................2-13
4 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

DRIVE GEAR, SPEED SENSOR ROTORÐ
SPEEDOMETER.....................21-183
DRIVE, GENERATOR REPLACEMENTÐ
LEFT HAND..........................8B-7
DRIVE, GENERATOR
REPLACEMENTÐRIGHT HAND...........8B-9
DRIVE PULLEY REPLACEMENT...........19-11
DRIVE (RHD), BELT TENSIONÐEXCEPT
RIGHT HAND.........................7-33
DRIVE (RHD), BELT TENSIONÐRIGHT
HAND...............................7-34
DRIVE SHAFTS.........................0-27
DRIVE VEHICLES, RIGHT HAND............23-1
DRIVE, WASHER PUMP REPLACEMENTÐ
LEFT HAND..........................8K-2
DRIVE, WASHER PUMP REPLACEMENTÐ
RIGHT HAND.........................8K-3
DRIVELINE SNAP; FRONT SUSPENSION
AND AXLE...........................2-17
DRIVELINE SNAP; REAR SUSPENSION
AND AXLES...........................3-8
DRIVELINE VIBRATION...................16-3
DRIVER SIDE..........................8R-2
DRIVERS DOOR POWER LOCK SWITCHÐ
2-DOOR LEFT HAND DRIVE.............8P-2
DRIVERS DOOR POWER LOCK SWITCHÐ
2-DOOR RIGHT HAND DRIVE............8P-3
DRIVERS DOOR POWER LOCK SWITCHÐ
4-DOOR.............................8P-4
DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR LEFT HAND DRIVE.....8S-6
DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR RIGHT HAND DRIVE....8S-7
DRIVERS DOOR POWER WINDOW
SWITCHÐ4-DOOR....................8S-5
DRIVETRAIN...........................0-22
DRL MODULE REPLACEMENT............8L-16
DRUM BRAKE ADJUSTMENT..............5-35
DRUM BRAKES........................5-34
DRUM BRAKESHOE INSTALLATION.........5-34
DRUM BRAKESHOE REMOVAL.............5-34
DRUM REFINISHING, BRAKE..............5-37
DRUMÐREAR SUPPORT OVERHAUL,
OVERRUNNING CLUTCHÐLOW-
REVERSE..........................21-118
DUCT, DEFROSTER NOZZLE..............24-40
DUCT, FRESH AIR INTAKE...............24-41
DUCT REPLACEMENT, DEFROSTER........24-29
DUCTS/HOSES/TUBING, RUBBER AND
PLASTIC............................0-19
ECU DIAGNOSIS.........................5-4
ECU OPERATION.......................5-46
ECU REPLACEMENTÐXJ.................5-53
ECU REPLACEMENTÐYJ.................5-53
EDGE GUARD/EDGE PROTECTOR STRIP,
DOOR.............................23-61
ELECTRICAL CIRCUITS, ABS SYSTEM
WIRING..............................5-4
ELECTRICAL CONTROL, FUEL PUMP........14-5
ELECTRICAL TESTS AT POWERTRAIN
CONTROL MODULE...................8H-6
ELECTRICAL TESTS AT SERVO............8H-5
ELECTRICAL TESTS, VEHICLE SPEED
CONTROL SYSTEM....................8H-5
ELECTRONIC CONTROL UNIT (ECU)........5-41
ELEMENT, ENGINE AIR CLEANER FILTER....0-16
ELEMENT TEST, OXYGEN SENSOR (O2S)
HEATING...........................14-45
EMISSION CONTROL INFORMATION
(VECI) LABEL, VEHICLE.................25-1
EMISSION CONTROLS, EVAPORATIVE.......25-4
EMISSION CONTROLS, EXHAUST..........25-7
EMR LAMPÐPCM OUTPUT..............14-24
END PLUG, HOUSING...................19-26
ENGINE ACCESSORY DRIVE BELTS.........7-31
ENGINE AIR CLEANER FILTER ELEMENT.....0-16
ENGINE AND TRANSMISSION/TRANSFER
CASE IDENTIFICATION..............INTRO.-3
ENGINE ASSEMBLY (SHORT BLOCK),
SERVICE.............................9-4
ENGINE ASSEMBLYÐXJ VEHICLES;
ENGINES
........................9-14,9-54
ENGINE ASSEMBLYÐYJ VEHICLES;
ENGINES
........................9-16,9-57
ENGINE BLOCK HEATER
..................7-37
ENGINE BREAK-IN
......................0-13ENGINE COOLANT TEMPERATURE
SENSOR; FUEL SYSTEM...............14-55
ENGINE COOLANT TEMPERATURE
SENSOR; IGNITION SYSTEMS......8D-4,8D-22
ENGINE COOLANT TEMPERATURE
SENSORÐPCM INPUT................14-21
ENGINE COOLANT TEMPERATURE
SENSOR TEST; FUEL SYSTEM..........14-43
ENGINE COOLANT TEMPERATURE
SENSOR TEST; IGNITION SYSTEMS......8D-12
ENGINE CYLINDER HEAD.............9-19,9-60
ENGINE CYLINDER HEAD COVER......9-18,9-59
ENGINE CYLINDER HEAD GASKET
FAILURE DIAGNOSIS....................9-5
ENGINE DAMPER.......................9-13
ENGINE DIAGNOSIS......................9-5
ENGINE, ENGINE EXHAUST MANIFOLDÐ
2.5L................................11-7
ENGINE, ENGINE EXHAUST MANIFOLDÐ
4.0L................................11-7
ENGINE, ENGINE FIRING ORDERÐ2.5L....8D-33
ENGINE, ENGINE FIRING ORDERÐ4.0L....8D-33
ENGINE EXHAUST MANIFOLDÐ2.5L
ENGINE.............................11-7
ENGINE EXHAUST MANIFOLDÐ4.0L
ENGINE.............................11-7
ENGINE FIRING ORDERÐ2.5L ENGINE.....8D-33
ENGINE FIRING ORDERÐ4.0L ENGINE.....8D-33
ENGINE FRONT SUPPORT CUSHION.......13-15
ENGINE, INTAKE MANIFOLDÐ2.5L.........11-8
ENGINE, INTAKE MANIFOLDÐ4.0L.........11-9
ENGINE MAINTENANCE..................0-13
ENGINE MOUNTÐREAR.............9-12,9-52
ENGINE MOUNTSÐFRONT...........9-10,9-51
ENGINE OIL...........................0-13
ENGINE OIL CHANGE AND FILTER
REPLACEMENT.......................0-15
ENGINE OIL FILTER.....................0-14
ENGINE ONLY, POWER STEERING
PRESSURE SWITCHÐ2.5L.............14-58
ENGINE PERFORMANCE...................9-2
ENGINE SERVICE PROCEDURES, 2.5L........9-9
ENGINE SERVICE PROCEDURES, 4.0L.......9-50
ENGINE SPECIFICATIONS....9-47,9-87,9-48,9-49,
9-88,9-89
ENGINE STARTER MOTOR SERVICE
PROCEDURES........................8B-4
ENGINE STARTER MOTOR TEST
PROCEDURES ON VEHICLE.............8A-9
ENGINE SUPPORTS.....................0-20
ENGINE, VACUUM ROUTING
SCHEMATICÐ2.5L 4 CYLINDER..........25-2
ENGINE, VACUUM ROUTING
SCHEMATICÐ4.0L 6 CYLINDER..........25-3
ENGINES, 2.5L........................8B-11
ENGINES, 4.0L........................8B-11
ENGINES, CONDENSERÐ4.0L............24-32
ENGINES, CONDENSER/RECEIVER
DRIERÐ2.5L........................24-31
ENGINES, FUEL USAGE STATEMENTÐ
GAS................................0-17
ENGINES, RECEIVER DRIERÐ4.0L........24-32
ENTRY, KEYLESS.......................8P-8
ENTRY SYSTEM SERVICE INFORMATION,
ILLUMINATED.......................8L-20
ENTRY SYSTEM TROUBLE DIAGNOSIS,
ILLUMINATED..................8L-21,8L-22
EQUIVALENT VALUES, CONVERSION
FORMULAS......................INTRO.-8
EVACUATION, SYSTEM...................24-4
EVAP CANISTER....................25-4,25-9
EVAP (EVAPORATION) CONTROL SYSTEM
....25-4
EVAPORATIVE EMISSION CONTROLS
.......25-4
EVAPORATOR AND HOUSING
.............24-42
EVAPORATOR COIL
....................24-34
EVAPORATOR/BLOWER HOUSING
.........24-33
EXHAUST EMISSION CONTROLS
...........25-7
EXHAUST GRILLEÐXJ VEHICLES, AIR
.....23-30
EXHAUST HEAT SHIELDS
.................11-1
EXHAUST MANIFOLDÐ2.5L ENGINE,
ENGINE
.............................11-7
EXHAUST MANIFOLDÐ4.0L ENGINE,
ENGINE
.............................11-7
EXHAUST PIPEÐXJ VEHICLES
............11-3
EXHAUST PIPEÐYJ VEHICLES
............11-4EXHAUST SYSTEM; EXHAUST SYSTEM
AND INTAKE MANIFOLD................11-1
EXHAUST SYSTEM; LUBRICATION AND
MAINTENANCE.......................0-20
EXHAUST SYSTEM DIAGNOSIS............11-2
EXHAUST TAILPIPEÐXJ VEHICLES,
MUFFLER............................11-5
EXHAUST TAILPIPEÐYJ VEHICLES,
MUFFLER............................11-6
EXPANSION (H) VALVE.............24-35,24-43
EXTENDED IDLE SWITCHÐPCM INPUT....14-21
EXTENDED IDLE SWITCH TEST...........14-45
EXTENSION PANELÐYJ RENEGADE
VEHICLES, FRONT FENDER............23-149
EXTENSION PANELÐYJ RENEGADE
VEHICLES, REAR QUARTER...........23-151
EXTENSION PANELÐYJ RENEGADE
VEHICLES, ROCKER.................23-150
EXTENSION PANELS AND FASCIASÐYJ
RENEGADE VEHICLES, BODY..........23-147
EXTENSIONÐXJ VEHICLES, QUARTER
TRIM PANEL.......................23-115
EXTERIOR BODY COLORS..............23-204
EXTERIOR COMPONENTS..........23-3,23-134
EXTERIOR LAMPS......................8L-1
EXTERIOR LAMPS, XJ..................8L-23
EXTERIOR LAMPS, YJ..................8L-23
EXTERIOR MOULDINGS, DOOR WINDOW . . . 23-61
EXTERIOR NAMEPLATES................23-30
EXTERIOR NAMEPLATES (ADHESIVE-
BACKED)..........................23-158
EXTERIOR PAINT CODES, XJ............23-205
EXTERIOR PAINT CODES, YJ............23-206
EXTERNAL HANDLE, DOOR..............23-55
EXTERNAL MIRRORS...................23-31
EXTERNAL RELEASE HANDLE, FULL-
METAL DOOR LATCH.................23-178
EXTERNAL SPARE/WHEEL TIRE CARRIER . . 23-172
EYE BUSHING REPLACEMENT, LEAF
SPRING; FRONT SUSPENSION
AND AXLE...........................2-15
EYE BUSHING REPLACEMENT, LEAF
SPRING; REAR SUSPENSION
AND AXLES........................3-4,3-6
FAILURE DIAGNOSIS, ENGINE CYLINDER
HEAD GASKET.........................9-5
FAN RELAYÐPCM OUTPUT, RADIATOR.....14-26
FANS, COOLING SYSTEM.................7-26
FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES, FRONT.........23-148
FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES, REAR..........23-152
FASCIASÐYJ RENEGADE VEHICLES,
BODY EXTENSION PANELS............23-147
FAULT DIAGNOSIS, ABS................5-4,5-6
FEED CIRCUIT TESTS - (VOLTAGE DROP
METHOD), STARTER...................8A-9
FENDER EXTENSION PANELÐYJ
RENEGADE VEHICLES, FRONT.........23-149
FENDER FLARE.......................23-144
FENDER, FRONT.......................23-14
FENDER INNER SPLASH SHIELDS........23-147
FENDER SPLASH APRONS..............23-147
FENDERS...........................23-141
FIELDÐPCM OUTPUT, GENERATOR.......14-25
FILL LEVEL, TRANSFER CASE...........21-294
FILLER DOOR BUMPERS, FUEL...........23-31
FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES, FUEL.....................23-86
FILLER NOZZLE/TUBE, FUEL
.............23-30
FILLER PROTECTOR/NOZZLE, FUEL
.......23-158
FILLER TUBE CAP, FUEL TANK;
EMISSION CONTROL SYSTEMS
......25-4,25-9
FILLER TUBE CAP, FUEL TANK; FUEL
SYSTEM
............................14-12
FILLER TUBE, NO-LEAD FUEL TANK
.......14-12
FILTER, AIR; EMISSION CONTROL
SYSTEMS
...........................25-9
FILTER, AIR; FUEL SYSTEM
..............14-54
FILTER BRACKET, FUEL
.................23-86
FILTER ELEMENT, ENGINE AIR CLEANER
....0-16
FILTER, ENGINE OIL
.....................0-14
FILTER, FUEL
.....................14-8,14-55
FILTER REPLACEMENT, ENGINE
OIL CHANGE
.........................0-15
8 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

FILTER REPLACEMENT, OIL.............21-100
FILTER SHIELD AND BRACKET, FUEL.......13-17
FINAL ASSEMBLY; FRONT SUSPENSION
AND AXLE...........................2-44
FINAL ASSEMBLY; REAR SUSPENSION
AND AXLES..........................3-26
FIRING ORDERÐ2.5L ENGINE, ENGINE....8D-33
FIRING ORDERÐ4.0L ENGINE, ENGINE....8D-33
FIRST GEAR (1) POSITION, HYDRAULIC
FLOW IN MANUAL...................21-94
FIRST GEAR, HYDRAULIC FLOW IN D
RANGE.............................21-87
FIRST-REVERSE BRAKE PISTON AND
TRANSMISSION CASE OVERHAUL......21-237
FIRST, SYMPTOM AND ACTIONÐSEE
PRELIMINARY CHECKS..................7-6
FIRSTÐTHIRDÐREVERSE GEAR
COMPONENTS......................21-159
FITTING CHART, CONNECTING ROD
BEARING........................9-36,9-76
FITTING CHART, MAIN BEARING.......9-43,9-83
FITTING O-RING SEAL, FLOW CONTROL
VALVE .............................19-12
FITTINGS, QUICK-CONNECT..........14-9,14-59
FITTINGS, SERVICING TRANSMISSION
COOLER LINES.....................21-106
FITTINGS, TRANSMISSION COOLER LINE . . 21-187
FIXED GLASS WATER LEAK DETECTION
AND REPAIR ..................23-83,23-189
FIXED WINDOW GLASS...........23-73,23-183
FIXED WINDOW GLASS, REAR DOOR......23-53
FLARE, FENDER......................23-144
FLARES AND LINERS, REAR
WHEELHOUSE.......................23-18
FLASHER, TURN SIGNALS AND HAZARD
WARNING...........................8A-1
FLOOR BRACKETSÐXJ VEHICLES,
SPARE TIRE/WHEEL HOLDDOWN.......23-128
FLOOR CONSOLEÐXJ VEHICLES, FULL . . . 23-125
FLOOR CONSOLES....................23-197
FLOOR MATS, CARPETS................23-129
FLOW CONTROL VALVE FITTING O-RING
SEAL..............................19-12
FLOW DURING FULL THROTTLE 3-2
DOWNSHIFT, HYDRAULIC..............21-92
FLOW DURING PART THROTTLE 3-2
DOWNSHIFT, HYDRAULIC..............21-91
FLOW IN D RANGE FIRST GEAR,
HYDRAULIC.........................21-87
FLOW IN D RANGE SECOND GEAR,
HYDRAULIC.........................21-88
FLOW IN D RANGE THIRD GEAR,
HYDRAULIC.........................21-89
FLOW IN MANUAL FIRST GEAR
(1) POSITION, HYDRAULIC.............21-94
FLOW IN MANUAL SECOND (2) RANGE,
HYDRAULIC.........................21-93
FLOW IN PARK AND NEUTRAL,
HYDRAULIC.........................21-86
FLOW IN REVERSE, HYDRAULIC..........21-95
FLOW IN THIRD GEAR (CONVERTER
CLUTCH ENGAGED), HYDRAULIC........21-90
FLOW TESTING, TRANSMISSION
COOLER...........................21-106
FLUID AND LEVELÐBRAKELINES
AND HOSES, BRAKE BLEEDINGÐ
BRAKE..............................5-13
FLUID CAPACITIES.......................0-4
FLUID, CLUTCH LINKAGE
..................6-1
FLUID CONTAMINATION, BRAKE
...........5-13
FLUID, IMPORTANCE OF CLEAN BRAKE
.....5-48
FLUID LEVEL AND CONDITION
...........21-69
FLUID LEVEL AND CONDITION,
CHECKING
....................21-96,21-173
FLUID LEVEL, BRAKE
....................5-13
FLUID LEVEL, CLUTCH
...................6-14
FLUID LEVEL, CORRECT
.................5-48
FLUID, RECOMMENDED
............21-66,21-96
FLUID, RECOMMENDED BRAKE; BRAKES
....5-13,
5-48
FLUID TUBE RETAINER CLIP, FUEL AND
BRAKE; BODY COMPONENTSÐXJ
VEHICLES
..........................23-86
FLUID TUBE RETAINER CLIP, FUEL
AND BRAKE; FRAME AND BUMPERS
.....13-16FLUID/LUBRICANTS/CLEANING
SOLVENTS, BRAKE.....................5-1
FLUSHING, COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING, TRANSMISSION COOLER
REVERSE..........................21-105
FLYWHEEL SERVICE.....................6-15
FOG LAMP BEAM ADJUSTMENT..........8L-12
FOG LAMP BULB/ELEMENT
REPLACEMENT......................8L-13
FOG LAMP REPLACEMENT..............8L-15
FOG LAMP SERVICE INFORMATION........8L-12
FOG LAMP SWITCH REPLACEMENT.......8L-14
FOG LAMP TROUBLE DIAGNOSIS.........8L-12
FOG LAMPÐYJ RENEGADE VEHICLES....23-150
FORM-IN-PLACE GASKETS.................9-1
FORMULAS AND EQUIVALENT VALUES,
CONVERSION.....................INTRO.-8
FORWARD CLUTCH OVERHAUL..........21-223
FOURTH GEAR OVERDRIVE COMPONENTS . . 21-158
FRAME ALIGNMENT....................13-10
FRAME, BUCKET SEATBACK COVER......23-100
FRAME CROSSMEMBER COVER..........13-14
FRAME INSPECTION/MEASUREMENTS.....13-10
FRAME REPAIR SERVICE................13-13
FRAME WEATHERSTRIP SEAL,
WINDSHIELD.......................23-185
FRAME, WINDSHIELD.................23-184
FRAME, YJ............................13-8
FRESH AIR DOOR VACUUM MOTOR.......24-41
FRESH AIR INTAKE DUCT...............24-41
FRESH AIR VENTILATION................24-39
FRONT AND REAR AXLES................0-26
FRONT AXLE, MODEL 30.................2-46
FRONT BAND ADJUSTMENT.............21-99
FRONT BUCKET SEATS..................23-97
FRONT BUMPER...................13-3,13-14
FRONT CABLE REPLACEMENT (YJ),
PARKING BRAKE......................5-62
FRONT CARPET/MATÐXJ VEHICLES......23-129
FRONT CLUTCH OVERHAUL.............21-125
FRONT DOOR SPACER BLOCKSÐTWO-
DOOR VEHICLES.....................23-60
FRONT DOOR VENT WINDOW............23-50
FRONT DOOR WINDOW GLASS...........23-49
FRONT DOOR WINDOW GLASS
REGULATOR........................23-48
FRONT DRIVE AXLE......................2-3
FRONT FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES................23-148
FRONT FENDER.......................23-14
FRONT FENDER EXTENSION PANELÐYJ
RENEGADE VEHICLES................23-149
FRONT INNER SCUFF PLATE/COWL SIDE
TRIM PANELÐXJ VEHICLES...........23-114
FRONT PARK/TURN SIGNAL LAMP BULB
REPLACEMENT.......................8L-8
FRONT PLANETARY GEAR OVERHAUL.....21-228
FRONT SERVO AND BAND OVERHAUL....21-136
FRONT SHOULDER BELT/BUCKLEÐXJ
VEHICLES.........................23-119
FRONT SHOULDER BELTS..............23-196
FRONT SKID PLATE....................23-84
FRONT SUPPORT CUSHION, ENGINE.......13-15
FRONT SUSPENSION.....................2-1
FRONT SUSPENSION COMPONENTS, XJ.....2-47
FRONT SUSPENSION COMPONENTS, YJ.....2-47
FRONT SUSPENSION, XJ.................2-10
FRONT SUSPENSION, YJ.................2-13
FRONT TOW HOOKS
....................13-5
FRONT WHEEL ALIGNMENT
................2-5
FRONT WHEEL BEARINGS
................0-31
FRONT WHEEL SENSOR INSTALLATION
.....5-49
FRONT WHEEL SENSOR REMOVAL
.........5-49
FRONT WIPER ARM AND PIVOT
ASSEMBLY REPLACEMENT
..............8K-9
FRONT WIPER ARM REPLACEMENT
........8K-8
FRONT WIPER BLADE REPLACEMENT
......8K-8
FRONT WIPER MOTOR
.................8K-10
FRONT WIPERS/WASHERS
...............8K-1
FRONT WIPERS/WASHERS GENERAL
INFORMATION
........................8K-8
FUEL AND BRAKE FLUID TUBE RETAINER
CLIP; BODY COMPONENTSÐXJ
VEHICLES
..........................23-86FUEL AND BRAKE FLUID TUBE
RETAINER CLIP; FRAME AND BUMPERS . . . 13-16
FUEL DELIVERY SYSTEM.................14-2
FUEL FILLER DOOR BUMPERS...........23-31
FUEL FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES..........................23-86
FUEL FILLER NOZZLE/TUBE..............23-30
FUEL FILLER PROTECTOR/NOZZLE.......23-158
FUEL FILTER......................14-8,14-55
FUEL FILTER BRACKET..................23-86
FUEL FILTER SHIELD AND BRACKET.......13-17
FUEL GAUGE..........................8E-2
FUEL GAUGE INOPERATIVE...............8E-3
FUEL GAUGE SENDING UNIT.............14-15
FUEL INJECTION (MFI)ÐCOMPONENT
DESCRIPTION/SYSTEM OPERATION,
MULTI-PORT........................14-17
FUEL INJECTION (MFI)ÐCOMPONENT
REMOVAL/INSTALLATION, MULTI-PORT . . . 14-54
FUEL INJECTION (MFI)ÐGENERAL
DIAGNOSIS, MULTI-PORT..............14-32
FUEL INJECTOR.......................14-55
FUEL INJECTORSÐPCM OUTPUT.........14-25
FUEL PRESSURE LEAK DOWN TEST........14-7
FUEL PRESSURE REGULATOR............14-30
FUEL PRESSURE RELEASE PROCEDURE.....14-5
FUEL PUMP CAPACITY TEST..............14-7
FUEL PUMP ELECTRICAL CONTROL........14-5
FUEL PUMP MODULE..............14-2,14-56
FUEL PUMP RELAY....................14-56
FUEL PUMP RELAYÐPCM OUTPUT.......14-25
FUEL PUMP RELAY TESTING.............14-44
FUEL RAIL...........................14-30
FUEL RAIL ASSEMBLY..................14-56
FUEL REQUIREMENTS....................0-2
FUEL SYSTEM........................14-62
FUEL SYSTEM PRESSURE RELEASE
PROCEDURE........................14-56
FUEL SYSTEM PRESSURE TEST......14-5,14-48
FUEL TANK...........................14-12
FUEL TANK CAPACITIES............14-12,14-62
FUEL TANK FILLER TUBE CAP;
EMISSION CONTROL SYSTEMS......25-4,25-9
FUEL TANK FILLER TUBE CAP; FUEL
SYSTEM............................14-12
FUEL TANK FILLER TUBE, NO-LEAD.......14-12
FUEL TANK PRESSURE RELIEF/
ROLLOVER VALVE...............14-15,14-56
FUEL TANK SKID PLATE; BODY
COMPONENTSÐXJ VEHICLES..........23-84
FUEL TANK SKID PLATE; FRAME AND
BUMPERS..........................13-16
FUEL TANK SUPPORT STRAP............23-86
FUEL TANKS.....................14-12,14-56
FUEL TUBES/LINES/HOSES AND CLAMPS . . . 14-9,
14-56
FUEL USAGE STATEMENT................14-1
FUEL USAGE STATEMENTÐGAS
ENGINES............................0-17
FUEL WARNING INOPERATIVE, LOW........8E-4
FUEL WARNING LAMP, LOW..............8E-2
FULL FLOOR CONSOLEÐXJ VEHICLES....23-125
FULL-METAL DOOR ASSIST HANDLE.....23-175
FULL-METAL DOOR HINGES............23-179
FULL-METAL DOOR KEY LOCK
CYLINDER.........................23-178
FULL-METAL DOOR LATCH.............23-179
FULL-METAL DOOR LATCH EXTERNAL
RELEASE HANDLE...................23-178
FULL-METAL DOOR LATCH INSIDE
RELEASE AND LOCK HANDLE..........23-175
FULL-METAL DOOR SERVICE............23-181
FULL-METAL DOOR TRIM PANEL........23-175
FULL-METAL DOOR VENT WINDOW
GLASS............................23-177
FULL-METAL DOOR WATERDAM.........23-176
FULL-METAL DOOR WEATHERSTRIP
SEALS............................23-180
FULL-METAL DOOR WINDOW GLASS.....23-178
FULL-METAL DOOR WINDOW GLASS
REGULATOR
.......................23-177
FULL-METAL DOOR WINDOW GLASS
REGULATOR HANDLE
................23-175
FUNCTION TROUBLE DIAGNOSISÐXJ
VEHICLES, HEADLAMP DELAY
..........8L-16
FUSE CHARTS AND RELAY BANKS
.........8W-8
JINDEX9
Description Group-Page Description Group-Page Description Group-Page

MODES OF OPERATION, OPEN LOOP/
CLOSED LOOP.......................14-27
MODULE, ELECTRICAL TESTS
AT POWERTRAIN CONTROL.............8H-6
MODULE, FUEL PUMP..............14-2,14-56
MODULE, INTERMITTENT WIPER..........8K-5
MODULE (PCM) 60-WAY CONNECTOR,
POWERTRAIN CONTROL...............14-38
MODULE (PCM), POWERTRAIN
CONTROL; EMISSION CONTROL
SYSTEMS...........................25-9
MODULE (PCM), POWERTRAIN CONTROL;
FUEL SYSTEM..................14-18,14-58
MODULE (PCM), POWERTRAIN CONTROL;
IGNITION SYSTEMS.........8D-6,8D-15,8D-28
MODULE REPLACEMENT, DRL............8L-16
MODULE REPLACEMENTÐXJ VEHICLES,
HEADLAMP DELAY...................8L-16
MODULE (TCM) SERVICE, TRANSMISSION
CONTROL.........................21-173
MODULEÐXJ VEHICLES, SENTINEL
HEADLAMP DELAY...................8L-15
MOTOR, A/C BLOWER..................24-43
MOTOR DIAGNOSIS, DISCONNECT AXLE/
SHIFT...............................2-27
MOTOR, FRESH AIR DOOR VACUUM.......24-41
MOTOR, FRONT WIPER.................8K-10
MOTOR (HEATING), BLOWER............24-40
MOTOR, IDLE AIR CONTROL (IAC)........14-56
MOTOR NOISE DIAGNOSIS, 2.5L
STARTER...........................8A-13
MOTORÐPCM OUTPUT, IDLE AIR
CONTROL (IAC)......................14-25
MOTOR RELAY TEST, STARTER...........14-48
MOTOR REMOVAL/INSTALLATION, 2.5L
STARTER............................8B-5
MOTOR REMOVAL/INSTALLATION,
4.0L STARTER........................8B-6
MOTOR REPLACEMENT, A/C
RECIRCULATING AIR DOOR VACUUM.....24-31
MOTOR REPLACEMENT, HEATER/
DEFROSTER/INSTRUMENT PANEL
OUTLET DOOR VACUUM...............24-30
MOTOR REPLACEMENT, POWER SEAT......8R-2
MOTOR REPLACEMENT, REAR WIPER.....8K-13
MOTOR RESISTORS REPLACEMENT,
BLOWER...........................24-35
MOTOR SERVICE PROCEDURES,
ENGINE STARTER.....................8B-4
MOTOR SPECIFICATIONS, 2.5L STARTER . . . 8B-11
MOTOR STALL TEST, ACTUATOR...........8P-6
MOTOR SWITCH REPLACEMENT,
BLOWER MOTOR/AIR DOOR............24-39
MOTOR TEST, IDLE AIR CONTROL........14-46
MOTOR TEST PROCEDURES ON
VEHICLE, ENGINE STARTER.............8A-9
MOTOR TORQUE SPECIFICATIONS,
STARTER...........................8B-11
MOTOR, WINDSHIELD WIPER.............8K-2
MOTOR/AIR DOOR MOTOR SWITCH
REPLACEMENT, BLOWER..............24-39
MOTOR/FAN REPLACEMENT, BLOWER.....24-26
MOULDING, BODY SIDE STEP...........23-145
MOULDING, WINDSHIELD REVEAL . . 23-73,23-183
MOULDING, WOODGRAIN...............23-19
MOULDINGÐXJ VEHICLES, DRIP RAIL.....23-29
MOULDINGÐXJ VEHICLES, WINDSHIELD
SIDE.............................23-114
MOULDING/CLADDING, BODY SIDE........23-19
MOULDINGS, DOOR WINDOW EXTERIOR . . . 23-61
MOUNTING, MATCH TIRES...............22-7
MOUNTÐREAR, ENGINE.............9-12,9-52
MOUNTSÐFRONT, ENGINE...........9-10,9-51
MUFFLER AND EXHAUST TAILPIPEÐXJ
VEHICLES...........................11-5
MUFFLER AND EXHAUST TAILPIPEÐ
YJ VEHICLES.........................11-6
MUFFLER AND TAILPIPE HEAT SHIELDS....13-17
MUFFLER/TAILPIPE HANGER BRACKET
.....13-16
MULTI-PORT FUEL INJECTION (MFI)Ð
COMPONENT DESCRIPTION/
SYSTEM OPERATION
..................14-17
MULTI-PORT FUEL INJECTION (MFI)Ð
COMPONENT REMOVAL/INSTALLATION
. . . 14-54
MULTI-PORT FUEL INJECTION (MFI)Ð
GENERAL DIAGNOSIS
.................14-32NAMEPLATES (ADHESIVE-BACKED),
EXTERIOR.........................23-158
NAMEPLATES, EXTERIOR................23-30
NEUTRAL, HYDRAULIC FLOW IN PARK.....21-86
NEUTRAL SWITCH, PARK...............14-58
NOISE DIAGNOSIS......................3-45
NOISE DIAGNOSIS, 2.5L STARTER MOTOR . . . 8A-13
NOISE DIAGNOSIS, RADIO................8F-2
NOISE, GEAR AND BEARING; FRONT
SUSPENSION AND AXLE................2-16
NOISE, GEAR AND BEARING; REAR
SUSPENSION AND AXLES................3-7
NOISE OR VIBRATION, TIRE..............22-4
NOISE/VIBRATION DIAGNOSIS, AXLE;
FRONT SUSPENSION AND AXLE..........2-16
NOISE/VIBRATION DIAGNOSIS, AXLE;
REAR SUSPENSION AND AXLES..........3-7
NO-LEAD FUEL TANK FILLER TUBE........14-12
NON-INTERMITTENT WINDSHIELD
WASHER, DIAGNOSING...............8K-12
NON-TILT STEERING COLUMN............19-50
NORMAL BRAKING MODE, ABS
OPERATION IN.......................5-43
NOTATION, METRIC SYSTEM..........INTRO.-8
NOTATIONÐSAE AND METRIC, THREAD . INTRO.-9
NOTATIONS, SPECIFICATION...........INTRO.-8
NOZZLE AND DUCT, DEFROSTER..........24-40
NOZZLE REPLACEMENT, WASHER.........8K-13
NOZZLE/TUBE, FUEL FILLER.............23-30
NP231 SERVICE DIAGNOSIS............21-274
NP231 TRANSFER CASE.........21-272,21-291
NP231 TRANSFER CASE, LEGEND FOR....21-292
NP231/NP242 TORQUE SPECIFICATIONS . . . 21-331
NP242 SERVICE DIAGNOSIS............21-295
NP242 TRANSFER CASE...............21-293
NP242 TRANSFER CASE, LEGEND FOR....21-319
NUMBER (VIN) DECODING, VEHICLE
IDENTIFICATION...................INTRO.-2
NUMBER (VIN) PLATE, VEHICLE
IDENTIFICATION...................INTRO.-1
NUT TIGHTENING, WHEEL............5-32,5-37
NUT, WHEEL LUG......................22-11
OFF DRAW (IOD) DIAGNOSIS, IGNITION.....8A-8
OIL CHANGE AND FILTER REPLACEMENT,
ENGINE.............................0-15
OIL COOLERS, TRANSMISSION............7-29
OIL, ENGINE...........................0-13
OIL FILTER, ENGINE.....................0-14
OIL FILTER REPLACEMENT.............21-100
OIL LEVEL, COMPRESSOR................24-6
OIL PAN ..........................9-32,9-72
OIL PRESSURE GAUGE..................8E-1
OIL PRESSURE GAUGE INOPERATIVE.......8E-3
OIL PRESSURE INDICATOR...............8E-1
OIL PRESSURE INDICATOR INOPERATIVE....8E-3
OIL PUMP........................9-33,9-73
OIL PUMP OVERHAUL...........21-122,21-206
OIL PUMP SEAL REPLACEMENT.........21-189
OIL PUMP WEAR LIMITS, AW-4.........21-325
OIL SEAL REPLACEMENT, INNER AXLE
SHAFT..............................2-33
OIL SEAL REPLACEMENT, TIMING CASE
COVER..........................9-26,9-67
OIL SEALS, REAR MAIN..............9-44,9-84
OIL SEALS, VALVE SPRINGS..........9-21,9-62
ON-BOARD DIAGNOSTIC SYSTEM,
USING.............................8A-19
ON-BOARD DIAGNOSTICS (OBD);
COOLING SYSTEM.....................7-4
ON-BOARD DIAGNOSTICS (OBD); FUEL
SYSTEM............................14-48
ON-BOARD DIAGNOSTICS (OBD);
IGNITION SYSTEMS..................8D-19
ONE GAUGE INOPERATIVE...............8E-22
ONE-WAY CLUTCH OVERHAUL, NO. 2.....21-234
ONE-WAY CLUTCH OVERHAUL, NO. 1.....21-229
OPEN CIRCUIT VOLTAGE, BATTERY.........8A-4
OPEN CIRCUIT VOLTAGE TEST, BATTERY....8A-3
OPEN LOOP/CLOSED LOOP MODES OF
OPERATION
.........................14-27
OPENING PANEL (GOP), GRILLE AND
GRILLE
.............................23-3
OPENING WEATHERSTRIP SEAL,
LIFTGATE
...........................23-70
OPENING WEATHERSTRIP SEALS,
DOOR WINDOW GLASS AND DOOR
......23-62OPERATING SOUND LEVELS...............5-3
OPERATING SPECIFICATIONS, PUMP.......19-3
OPERATION, ABS SYSTEM................5-39
OPERATION, A/C........................24-1
OPERATION, ACCELERATION SWITCH.......5-45
OPERATION AND APPLICATION CHARTS,
GEARTRAIN........................21-159
OPERATION AND WEAR COMPENSATION,
CALIPER............................5-24
OPERATION, ANTILOCK BRAKE
SYSTEM............................5-43
OPERATION; CHIME/BUZZER
WARNING SYSTEMS...................8U-1
OPERATION, CLUTCH.....................6-2
OPERATION, COMPONENT
IDENTIFICATION/SYSTEM...............8D-1
OPERATION, COMPONENTS.............21-157
OPERATION, ECU
.......................5-46
OPERATION, HCU PUMP AND PEDAL
TRAVEL SENSOR
......................5-44
OPERATION, HCU SOLENOID VALVE
........5-43
OPERATION, HEATER/DEFROSTER
.........24-37
OPERATION IN ANTILOCK BRAKING
MODE, ABS
..........................5-43
OPERATION IN NORMAL BRAKING MODE,
ABS
................................5-43
OPERATION, MULTI-PORT FUEL
INJECTION (MFI)ÐCOMPONENT
DESCRIPTION/SYSTEM
................14-17
OPERATION, OPEN LOOP/CLOSED LOOP
MODES OF
..........................14-27
OPERATION, PARKING BRAKE
.............5-56
OPERATION, POWER BRAKE BOOSTER
......5-22
OPERATION, POWER STEERING PUMPÐ
INITIAL
............................19-13
OPERATION; REAR SUSPENSION AND
AXLES
..............................3-44
OPERATION, SYSTEM
...................8P-9
OPERATION, WHEEL SPEED SENSOR
.......5-45
OPERATION/DIAGNOSIS
..................8U-1
OPERATIONAL CHECK (ROAD TEST)
........8H-7
OPERATIONAL CHECK WITH BATTERY
INDICATOR (BASE CLUSTER ONLY)
......8A-14
OPERATIONAL CHECK WITH VOLTMETER
. . . 8A-15
O-RING SEAL, FLOW CONTROL VALVE
FITTING
............................19-12
ORNAMENTATION, WHEEL
................22-6
OUTER SCUFF PLATESÐXJ VEHICLES
....23-118
OUTLET DOOR VACUUM MOTOR
REPLACEMENT, HEATER/DEFROSTER/
INSTRUMENT PANEL
..................24-30
OUTPUT, AIR CONDITIONING CLUTCH
RELAYÐPCM
.......................14-24
OUTPUT, AUTO SHUT DOWN (ASD)
RELAYÐPCM
.......................14-24
OUTPUT, DATA LINK CONNECTORÐPCM
. . . 14-24
OUTPUT, EMR LAMPÐPCM
..............14-24
OUTPUT, FUEL INJECTORSÐPCM
.........14-25
OUTPUT, FUEL PUMP RELAYÐPCM
.......14-25
OUTPUT, GENERATOR FIELDÐPCM
.......14-25
OUTPUT, GENERATOR LAMPÐPCM
.......14-25
OUTPUT, IDLE AIR CONTROL (IAC)
MOTORÐPCM
.......................14-25
OUTPUT, IGNITION COILÐPCM
...........14-26
OUTPUT, MALFUNCTION INDICATOR
LAMPÐPCM
........................14-26
OUTPUT, RADIATOR FAN RELAYÐPCM
.....14-26
OUTPUT, SCI TRANSMITÐPCM
...........14-26
OUTPUT SHAFT OVERHAUL, NO. 2 ONE-
WAY CLUTCH
......................21-234
OUTPUT, SHIFT INDICATORÐPCM
........14-26
OUTPUT, SPEED CONTROLÐPCM
.........14-27
OUTPUT, TACHOMETERÐPCM
...........14-27
OUTPUT, TORQUE CONVERTER CLUTCH
RELAYÐPCM
.......................14-27
OUTPUT VOLTAGE SPECIFICATIONS
.......8B-12
OVERDRIVE COMPONENTS, FOURTH
GEAR
.............................21-158
OVERDRIVE PLANETARY GEAR AND
CLUTCH OVERHAUL
.................21-209
OVERDRIVE SUPPORT OVERHAUL
.......21-216
JINDEX15
Description Group-Page Description Group-Page Description Group-Page

SECOND (2) RANGE, HYDRAULIC FLOW
IN MANUAL.........................21-93
SECOND BRAKE OVERHAUL............21-232
SECOND COAST BRAKE SERVO..........21-181
SECOND GEAR, HYDRAULIC FLOW IN D
RANGE.............................21-88
SECONDARY CABLES, SPARK PLUG . . 8D-17,8D-29
SECONDARY CIRCUIT DIAGNOSIS,
IGNITION...........................8D-12
SECONDARY IGNITION WIRING...........8W-1
SELECTIVE SNAP RING CHARTÐAX 15
MANUAL TRANSMISSION.............21-321
SELECTOR INDICATOR REPLACEMENTÐ
INSTRUMENT CLUSTER REMOVED,
GEAR...............................8E-6
SENDING UNIT, FUEL GAUGE.............14-15
SENSEÐPCM INPUT, AUTOMATIC SHUT
DOWN (ASD)........................14-19
SENSEÐPCM INPUT, IGNITION CIRCUIT....14-21
SENSOR AIR GAP ADJUSTMENT, WHEEL....5-49
SENSOR AIR GAP, REAR SPEED............5-3
SENSOR, CAMSHAFT POSITION; FUEL
SYSTEM............................14-54
SENSOR, CAMSHAFT POSITION;
IGNITION SYSTEMS..............8D-1,8D-20
SENSOR, COOLANT TEMPERATURE........25-9
SENSOR, CRANKSHAFT POSITION; FUEL
SYSTEM............................14-55
SENSOR, CRANKSHAFT POSITION;
IGNITION SYSTEMS..............8D-2,8D-21
SENSOR, ENGINE COOLANT
TEMPERATURE; FUEL SYSTEM..........14-55
SENSOR, ENGINE COOLANT TEMPERATURE;
IGNITION SYSTEMS..............8D-4,8D-22
SENSOR INPUT, LOSS OF.................5-3
SENSOR INSTALLATION, ACCELERATION....5-52
SENSOR INSTALLATION, FRONT WHEEL.....5-49
SENSOR INSTALLATION, REAR WHEEL......5-50
SENSOR, INTAKE AIR TEMPERATURE......14-54
SENSOR, INTAKE MANIFOLD AIR
TEMPERATURE..................8D-5,8D-27
SENSOR, MANIFOLD ABSOLUTE
PRESSURE (MAP); FUEL SYSTEM.......14-57
SENSOR, MANIFOLD ABSOLUTE
PRESSURE (MAP); IGNITION SYSTEMS . . . 8D-5,
8D-27
SENSOR (O2S) HEATING ELEMENT TEST,
OXYGEN............................14-45
SENSOR OPERATION, HCU PUMP
AND PEDAL TRAVEL...................5-44
SENSOR OPERATION, WHEEL SPEED.......5-45
SENSOR, OXYGEN (O2S); EMISSION
CONTROL SYSTEMS...............25-7,25-9
SENSOR, OXYGEN (O2S); FUEL SYSTEM . . . 14-57
SENSOR, OXYGEN (O2S); IGNITION
SYSTEMS..........................8D-28
SENSORÐPCM INPUT, CAMSHAFT
POSITION..........................14-20
SENSORÐPCM INPUT, CRANKSHAFT
POSITION..........................14-20
SENSORÐPCM INPUT, ENGINE
COOLANT TEMPERATURE..............14-21
SENSORÐPCM INPUT, INTAKE AIR
TEMPERATURE......................14-20
SENSORÐPCM INPUT, MANIFOLD
ABSOLUTEPRESSURE (MAP)...........14-21
SENSORÐPCM INPUT, OXYGEN (O2S).....14-22
SENSORÐPCM INPUT, VEHICLE SPEED
....14-23
SENSOR, PEDAL TRAVEL
.................5-41
SENSOR REMOVAL, ACCELERATION
........5-52
SENSOR REMOVAL, FRONT WHEEL
........5-49
SENSOR REMOVAL, REAR WHEEL
.........5-49
SENSOR RESISTANCE (OHMS)ÐCOOLANT
TEMPERATURE SENSOR/MANIFOLD AIR
TEMPERATURE FUEL SYSTEM
..........14-43
SENSOR RESISTANCE (OHMS); IGNITION
SYSTEMS
.....................8D-12,8D-14
SENSOR ROTORÐSPEEDOMETER
DRIVE GEAR, SPEED
.................21-183
SENSOR SERVICE, PEDAL TRAVEL
.........5-51
SENSOR, SPEED
......................21-182
SENSOR SYSTEM REPAIR PROCEDURES,
THERMOMETER
......................8C-6
SENSOR TEST, CAMSHAFT POSITION;
FUEL SYSTEM
.......................14-43SENSOR TEST, CAMSHAFT POSITION;
IGNITION SYSTEMS...................8D-8
SENSOR TEST, CRANKSHAFT POSITION;
FUEL SYSTEM.......................14-44
SENSOR TEST, CRANKSHAFT POSITION;
IGNITION SYSTEMS...................8D-9
SENSOR TEST, ENGINE COOLANT
TEMPERATURE; FUEL SYSTEM..........14-43
SENSOR TEST, ENGINE COOLANT
TEMPERATURE; IGNITION SYSTEMS.....8D-12
SENSOR TEST, INTAKE AIR TEMPERATURE . . . 14-43
SENSOR TEST, INTAKE MANIFOLD AIR
TEMPERATURE......................8D-14
SENSOR TEST, MANIFOLD ABSOLUTE
PRESSURE (MAP); FUEL SYSTEM.......14-44
SENSOR TEST, MANIFOLD ABSOLUTE
PRESSURE (MAP); IGNITION
SYSTEMS..........................8D-14
SENSOR TEST, THROTTLE POSITION......8D-18
SENSOR TEST, VEHICLE SPEED; FUEL
SYSTEM............................14-45
SENSOR TEST, VEHICLE SPEED;
VEHICLE SPEED CONTROL SYSTEM......8H-5
SENSOR TESTS, OXYGEN...............8D-19
SENSOR, THROTTLE POSITION............8D-6
SENSOR (TPS)ÐPCM INPUT, THROTTLE
POSITION..........................14-23
SENSOR (TPS) SERVICE, THROTTLE
POSITION.........................21-184
SENSOR (TPS) TEST, THROTTLE
POSITION..........................14-45
SENSOR (TPS), THROTTLE POSITION;
FUEL SYSTEM.......................14-59
SENSOR (TPS), THROTTLE POSITION;
IGNITION SYSTEMS..................8D-29
SENSOR, VEHICLE SPEED...............14-60
SENSOR/MANIFOLD AIR TEMPERATURE,
SENSOR RESISTANCE (OHMS)ÐCOOLANT
TEMPERATURE FUEL SYSTEM..........14-43
SENSORS, WHEEL SPEED................5-41
SENTINEL HEADLAMP DELAY MODULEÐ
XJ VEHICLES........................8L-15
SERPENTINE DRIVE BELT DIAGNOSIS.......7-32
SERVICING TRANSMISSION COOLER
LINES AND FITTINGS................21-106
SERVO AND BAND OVERHAUL, FRONT....21-136
SERVO AND BAND OVERHAUL, REAR.....21-136
SERVO CABLE REPLACEMENT............8H-9
SERVO, ELECTRICAL TESTS AT............8H-5
SERVO REPLACEMENT, SPEED CONTROL....8H-9
SERVO, SECOND COAST BRAKE.........21-181
SEVERE SERVICE MAINTENANCE...........0-5
SHAFT AND SIDE COVER REPLACEMENT,
PITMAN............................19-26
SHAFT, AXLE..........................3-14
SHAFT AXLEÐCARDAN U-JOINT...........2-25
SHAFT, HUB BEARING AND AXLE..........2-24
SHAFT, INTERMEDIATE (COUPLER)........19-43
SHAFT, INTERMEDIATE (COUPLING).......19-21
SHAFT OIL SEAL REPLACEMENT, INNER
AXLE...............................2-33
SHAFT OVERHAUL, MANUAL VALVE......21-205
SHAFT OVERHAUL, NO. 2 ONE-WAY
CLUTCH AND OUTPUT...............21-234
SHAFT REPLACEMENT, PROPELLER........16-7
SHAFT REPLACEMENT, RACK PISTON
AND WORM.........................19-30
SHAFT SEAL AND BEARING, AXLE.........3-15
SHAFT, SEAL AND BEARING SERVICE,
AXLE...............................3-31
SHAFT SEAL REPLACEMENT, MANUAL
VALVE ............................21-178
SHAFT SEAL REPLACEMENT, PINION.......3-13
SHAFT SEAL REPLACEMENT, PITMAN......19-35
SHAFT SEALS AND BEARING
REPLACEMENT, PITMAN...............19-32
SHAFT SEALSÐIN CAR REPLACEMENT,
PITMAN............................19-21
SHAFTS AND U-JOINTS, PROPELLER......16-14
SHAFTS, DRIVE........................0-27
SHAFTS, PROPELLER....................16-1
SHEETS AND INDEXES, WIRING DIAGRAM
. . . 8W-1
SHIELD AND BRACKET, FUEL FILTER
.......13-17
SHIELD, GENERATOR SPLASH
............13-14
SHIELDÐXJ VEHICLES, FUEL FILLER
HOSE SPLASH
.......................23-86SHIELDS, EXHAUST HEAT
................11-1
SHIELDS, FENDER INNER SPLASH
.......23-147
SHIELDS, HEAT
.......................14-12
SHIELDS, MUFFLER AND TAILPIPE HEAT
. . . 13-17
SHIFT AUTOMATIC, PARK-LOCK CABLEÐ
CONSOLE
...........................19-45
SHIFT CABLE ADJUSTMENT
.............21-186
SHIFT CABLE ADJUSTMENT (XJ)
..........21-97
SHIFT, DISASSEMBLYÐCOLUMN OR
CONSOLE
...........................19-50
SHIFT INDICATORÐPCM OUTPUT
.........14-26
SHIFT LEVER POSITIONS, TRANSMISSION
RANGES
...........................21-157
SHIFT LINKAGE ADJUSTMENT
.....21-275,21-296
SHIFT PATTERN
........................21-2
SHIFT PATTERN, TRANSMISSION
.........21-33
SHIFTING TEST, MANUAL
...............21-168
SHIM PACK MEASUREMENT AND
ADJUSTMENT, DIFFERENTIAL
............2-42
SHOCK ABSORBER; FRONT SUSPENSION
AND AXLE
.......................2-12,2-14
SHOCK ABSORBER; REAR SUSPENSION
AND AXLES
........................3-3,3-5
SHOCK DIAGNOSIS, SPRING AND; FRONT
SUSPENSION AND AXLE
............2-12,2-14
SHOCK DIAGNOSIS, SPRING AND; REAR
SUSPENSION AND AXLES
.............3-3,3-5
SHORT BLOCK, SERVICE ENGINE ASSEMBLY
. . 9-4
SHOULDER BELT/BUCKLEÐXJ
VEHICLES, FRONT
...................23-119
SHOULDER BELTS, FRONT
..............23-196
SHOULDER BELTS, REAR
...............23-196
SHOULDER/LAP BELT/BUCKLEÐXJ
VEHICLES, REAR
....................23-120
SHUT DOWN (ASD) RELAY, AUTOMATIC;
FUEL SYSTEM
.......................14-54
SHUT DOWN (ASD) RELAY, AUTOMATIC;
IGNITION SYSTEMS
..........8D-1,8D-8,8D-20
SHUT DOWN (ASD) RELAYÐPCM
OUTPUT, AUTO
......................14-24
SHUT DOWN (ASD) SENSEÐPCM INPUT,
AUTOMATIC
.........................14-19
SHUTDOWN (ASD) RELAY TESTING,
AUTOMATIC
.........................14-43
SIDE COVER REPLACEMENT, PITMAN
SHAFT
.............................19-26
SIDE MARKER LAMP BULB
REPLACEMENT
.......................8L-7
SIDE MOULDING/CLADDING, BODY
........23-19
SIDE MOULDINGÐXJ VEHICLES,
WINDSHIELD
.......................23-114
SIDE STEP MOULDING, BODY
...........23-145
SIDE TRIM PANELÐXJ VEHICLES,
FRONT INNER SCUFF PLATE/COWL
.....23-114
SIGHT GLASS
.........................24-41
SIGNAL LAMP BULB REPLACEMENT,
FRONT PARK/TURN
....................8L-8
SIGNALS, WHEEL/TIRE SIZE AND INPUT
.....5-3
SIGNALSÐXJ, TURN
....................8J-1
SIGNALSÐYJ, TURN
....................8J-2
SIGNAL/TAIL LAMP BULB REPLACEMENT,
BACK-UP/REAR TURN
..................8L-9
SINGLE CARDAN
.......................16-9
SIZE AND INPUT SIGNALS, WHEEL/TIRE
.....5-3
SKID PLATE, FRONT
....................23-84
SKID PLATE, FUEL TANK; BODY
COMPONENTSÐXJ VEHICLES
.....13-16,23-84
SKID PLATE, TRANSFER CASE; FRAME
AND BUMPERS Ð XJ VEHICLES
. . . 13-15,23-84
SKID PLATEÐYJ RENEGADE VEHICLES,
FRONT
............................23-148
SKID PLATEÐYJ RENEGADE VEHICLES,
REAR
.............................23-152
SLIP DIFFERENTIAL, LIMITED
..............3-8
SNAP, DRIVELINE; FRONT SUSPENSION
AND AXLE
...........................2-17
SNAP, DRIVELINE; REAR SUSPENSION
AND AXLES
...........................3-8
SNAP RING CHARTÐAX 15 MANUAL
TRANSMISSION, SELECTIVE
...........21-321
20 INDEXJ
Description Group-Page Description Group-Page Description Group-Page