1994 JEEP CHEROKEE coolant temperature

(12) Fill and bleed the cooling system.
FRESH AIR DOOR VACUUM MOTOR
REMOVAL
(1) Remove the glove box and assist handle.
(2) Disconnect the vacuum hose from the motor.
(3) Remove the motor lever retaining clip.
(4) Remove the motor attaching nuts and remove
the motor from the fresh air duct.
INSTALLATION
(1) Position the motor on the fresh air duct and in-
stall the motor attaching nuts.
(2) Align the motor lever with the air door lever
and install the lever retaining clip.
(3) Connect the vacuum hose to the motor.
(4) Install the glove box and assist handle.
FRESH AIR INTAKE DUCT
REMOVAL
WARNING: HOT ENGINE COOLANT CAN CAUSE
SEVERE BURNS. DO NOT OPEN THE RADIATOR
DRAIN COCK WHEN THE COOLING SYSTEM IS
HOT AND PRESSURIZED. ALLOW THE COOLANT
TO DECREASE TO ROOM TEMPERATURE BEFORE
STARTING REPAIR OPERATIONS.
(1) Drain approximately 1.9 liters (2 qts) of coolant
from the radiator. Drain the coolant into a clean con-
tainer.
(2) Disconnect the heater hoses.
(3) Remove the nuts attaching the heater housing
studs to the dash panel from inside the engine com-
partment.
(4) Disconnect the speedometer cable.
(5) Remove the glove box and assist handle.
(6) Tilt the heater housing back and pull it rear-
ward and out from under the instrument panel.
(7) Disconnect the vent cables.
(8) Remove the fresh air intake grille from the
cowl.
(9) Remove the fresh air intake duct.
INSTALLATION
(1) Install the fresh air intake duct.
(2) Install the defroster nozzle and duct.
(3) Raise and secure the windshield.
(4) Install the fresh air grille on the cowl.
(5) Install the vent cables.
(6) Position the heater housing on the dash panel.
Be sure all the housing studs extend through the
dash panel.
(7) Install the seals on the blower motor and
heater core inlet and outlet tubes.
(8) Install the attaching nuts on the heater hous-
ing studs.CAUTION: DO NOT over tighten the attaching nuts.
The housing could become distorted causing air
leaks and improper heater door operation. Tighten
the nuts alternately and evenly until 2 stud threads
are visible beyond each nut.
(9) Install the glove box and assist handle.
(10) Connect the speedometer cable.
(11) Connect the heater hoses.
(12) Fill and bleed the cooling system.
DESCRIPTION (AIR CONDITIONING)
The evaporator, blower fan and motor, thermostat,
expansion valve, capillary tube, air outlets and sys-
tem controls are located in the evaporator housing.
The evaporator housing is mounted under the instru-
ment panel. The compressor, condenser, receiver-
dryer and refrigerant lines are located in the engine
compartment.
A rotary-type compressor with magnetic clutch op-
erated drive pulley is used for all vehicles equipped
with air conditioning.
SIGHT GLASS
A sight glass is located on the top of the receiver-
drier (Fig. 6). The sight glass provides a visual check
of system refrigerant level. A continuous stream of
bubbles will appear in the sight glass when system
charge is low. Bubbles will not appear when the sys-
tem is fully charged.
A/C CONTROL PANEL
FAN SWITCH
The fan switch may be serviced by removing the
access plate located on the lower evaporator core
housing.
TEMPERATURE CONTROL THERMOSTAT
REMOVAL
(1) Lower the evaporator housing.
(2) Remove the attaching screws holding the top
and bottom housings together.
(3) Separate the housings.
(4) Remove the thermostat.
Fig. 6 Sight Glass (Typical)
JHEATING AND AIR CONDITIONING 24 - 41

INSTALLATION
(1) When installing a replacement temperature
control thermostat, insert the capillary tube into the
evaporator coil a minimum of 50 mm (2 inch) (Fig.
7).
CAUTION: Handle the tube with care to avoid bends
or kinks that could cause the thermostat to mal-
function.
(2) Assemble the housing and install the attaching
screws. DO NOT over tighten the attaching screws.
(3) Install the evaporator housing.
A/C CONDENSER
REMOVAL
WARNING: DO NOT LOOSEN THE RADIATOR
DRAIN COCK WHEN THE COOLING SYSTEM IS
HOT AND PRESSURIZED. HOT COOLANT CAN
CAUSE SERIOUS BURNS.
(1) Discharge the system slowly to prevent loss of
compressor oil.
(2) Drain the radiator. Drain the coolant into a
clean container.
(3) Remove the fan shroud and radiator.
(4) Disconnect the pressure pipe fitting from the
condenser.
(5) Remove the condenser attaching screws and tilt
the bottom of the condenser toward the engine.Plug
all the condenser openings to prevent entry of
dirt or moisture.
(6) Working from under the vehicle, disconnect the
receiver-drier to-evaporator hose fitting from the re-
ceiver-drier.
(7) Remove the condenser and receiver-drier as an
assembly.
(8) Remove the receiver-drier from the condenser,
if necessary.
INSTALLATION
(1) If the condenser is replaced, add 30 ml (1 fluid
oz.) of refrigerant oil to the system.(2) Attach the receiver-drier to the condenser.
(3) Place the condenser in position and connect the
hose fitting to the receiver-drier.
(4) Install the condenser attaching screws.
(5) Connect the condenser pressure pipe fitting.
(6) Install the radiator and fan shroud.
(7) Fill the cooling system.
(8) Evacuate, charge and leak test the air condi-
tioning system.
RECEIVER-DRIER REPLACEMENT
REMOVAL
(1) Discharge the system slowly to prevent loss of
compressor oil.
(2) Disconnect the evaporator and condenser hose
fittings from the receiver-drier.
(3) Remove the receiver-drier attaching screws. Re-
move the receiver-drier.
INSTALLATION
(1) Position the receiver-drier in place. Install and
tighten the receiver-drier attaching screws.
(2) Connect the evaporator and condenser hose fit-
tings to the receiver-drier.
(3) Charge the system.
(4) Preform the leak test on the system.
EVAPORATOR AND HOUSING
REMOVAL
(1) Discharge the system.Discharge the system
slowly to prevent loss of compressor oil.
(2) Disconnect the inlet (suction) hose.
(3) Disconnect the receiver-drier-to-evaporator
hoses.
(4) Remove the hose clamps and dash grommet re-
taining screws.
(5) Remove the evaporator housing-to-instrument
panel attaching screws and the housing mounting
bracket screw (Fig. 8).
Fig. 7 Temperature Control Thermostat
Fig. 8 Evaporator Housing
24 - 42 HEATING AND AIR CONDITIONINGJ

COMPONENT REMOVAL/INSTALLATION
INDEX
page page
Air Cleaner Housing....................... 8
Air Filter................................ 9
Coolant Temperature Sensor................. 9
EVAP Canister........................... 9Fuel Tank Filler Tube Cap.................. 9
Oxygen (O2S) Sensor...................... 9
Powertrain Control Module (PCM)............. 9
Pressure Relief/Rollover Valve................ 9
AIR CLEANER HOUSING
REMOVAL
(1) Unlock clean air hose clamp (Figs. 3 or 4) at
air cleaner cover. To unlock the clamp, attach adjust-
able pliers to clamp and rotate pliers as shown in fig-
ure 3. Remove clean air hose at cover.
(2) Disconnect vacuum lines at air cleaner hous-
ing.
(3) YJ Models: Release the three over-center type
clamps securing the housing to the housing bracket.
XJ Models: Remove the housing cover and remove
air filter. Remove two bolts and one nut.
(4) Release the air cleaner housing from the ambi-
ent air inlet and remove housing from vehicle.
INSTALLATION
(1) Position air cleaner housing to body and ambi-
ent air inlet.
(2) YJ Models: Lock the three over-center type
clamps securing the housing to the housing bracket.
XJ Models: Install two bolts and one nut to housing.Fig. 3 Air CleanerÐXJ ModelsÐTypical
Fig. 4 Air CleanerÐYJ ModelsÐTypical
Fig. 5 Clamp Removal
25 - 8 EMISSION CONTROL SYSTEMSJ

Install air filter and cover.
(3) Install vacuum lines to housing.
(4) Install clean air hose and clamp to cover. Com-
press the clamp snugly with adjustable pliers as
shown in figure 6.
AIR FILTER
REMOVAL/INSTALLATION
(1) Pry back the six clips (YJ Models) or three clips
(XJ Models) retaining the air cleaner cover to the air
cleaner housing.
(2) Lift the cover up and position to the side.
(3) Remove air filter.
(4) Clean the inside of air cleaner housing before
installing new filter.
(5) Reverse the preceding operation for installa-
tion. Be sure the air cleaner cover is properly seated
to air cleaner housing.
COOLANT TEMPERATURE SENSOR
For description, operation, diagnosis and removal/
installation procedures of the engine coolant temper-
ature sensor, refer to Group 14, Fuel Systems.
EVAP CANISTER
On XJ models, the EVAP canister is located in the
engine compartment on the passenger side frame rail
(Fig. 7). On YJ models, the EVAP canister is located
in the engine compartment on the dash panel and be-
low the brake master cylinder (Fig. 8).
REMOVAL/INSTALLATION
(1) Disconnect the vacuum lines at the EVAP can-
ister. Note location of lines before removal.
(2) Remove canister retaining strap bolt.
(3) Remove canister from vehicle.Reverse the procedure for installation.
FUEL TANK FILLER TUBE CAP
If replacement of the fuel filler tube cap is neces-
sary, it must be replaced with an identical cap to be
sure of correct system operation.
OXYGEN (O2S) SENSOR
For description, operation, diagnosis and removal/
installation procedures of the O2S sensor, refer to
Group 14, Fuel Systems.
POWERTRAIN CONTROL MODULE (PCM)
For removal and installation procedures, refer to
Group 14, Fuel Systems.
PRESSURE RELIEF/ROLLOVER VALVE
For removal and installation procedures, refer to
the Fuel Tank section of Group 14, Fuel Systems.
Fig. 7 EVAP CanisterÐXJ Models
Fig. 8 EVAP CanisterÐYJ Models
Fig. 6 Clamp Installation
JEMISSION CONTROL SYSTEMS 25 - 9

30RH/32RH AUTOMATIC TRANSMISSION . . . 21-66
30RH/32RH GENERAL SPECIFICATIONS . . . 21-322
30RH/32RH IN-VEHICLE SERVICE.........21-96
30RH/32RH PRESSURE TEST
SPECIFICATIONS....................21-323
30RH/32RH SNAP RING/THRUST
WASHER/THRUST PLATE
SPECIFICATIONS....................21-322
30RH/32RH TORQUE SPECIFICATIONS....21-323
30RH/32RH TRANSMISSION DIAGNOSIS . . . 21-69,
21-77,21-78,21-79,21-80,21-81,21-82,21-83,21-84,
21-85
30RH/32RH TRANSMISSION OVERHAUL . . . 21-112
30RH/32RH TRANSMISSION REMOVAL
AND INSTALLATION..................21-108
3-2 DOWNSHIFT, HYDRAULIC FLOW
DURING FULL THROTTLE..............21-92
3-2 DOWNSHIFT, HYDRAULIC FLOW
DURING PART THROTTLE..............21-91
4WD INDICATOR......................8E-22
4WD INDICATOR INOPERATIVE............8E-4
4WD INDICATOR LAMP..................8E-2
60-WAY CONNECTOR, POWERTRAIN
CONTROL MODULE (PCM).............14-38
ABBREVIATIONS, SYMBOLS, FUSES........8W-6
ABS BRAKE DIAGNOSIS...................5-3
ABS BRAKES, BRAKE BLEEDINGÐWITH.....5-14
ABS COMPONENT SERVICE...............5-47
ABS FAULT DIAGNOSIS................5-4,5-6
ABS OPERATION IN ANTILOCK BRAKING
MODE..............................5-43
ABS OPERATION IN NORMAL BRAKING
MODE..............................5-43
ABS SYSTEM OPERATION................5-39
ABS SYSTEM WIRING AND ELECTRICAL
CIRCUITS............................5-4
ABS WARNING LIGHT DISPLAY.............5-3
ABSOLUTE PRESSURE (MAP) SENSOR,
MANIFOLD; FUEL SYSTEM.............14-57
ABSOLUTE PRESSURE (MAP) SENSOR,
MANIFOLD; IGNITION SYSTEMS....8D-5,8D-27
ABSOLUTE PRESSURE (MAP) SENSORÐ
PCM INPUT, MANIFOLD...............14-21
ABSOLUTE PRESSURE (MAP) SENSOR
TEST, MANIFOLD; FUEL SYSTEM........14-44
ABSOLUTE PRESSURE (MAP) SENSOR
TEST, MANIFOLD; IGNITION
SYSTEMS..........................8D-14
ABSORBER, SHOCK; FRONT
SUSPENSION AND AXLE............2-12,2-14
ABSORBER, SHOCK; REAR SUSPENSION
AND AXLES........................3-3,3-5
A/C BLOWER MOTOR...................24-43
A/C CONDENSER......................24-42
A/C CONTROL PANEL...................24-41
A/C CONTROL PANEL REPLACEMENT,
HEATER ............................24-26
A/C OPERATION........................24-1
A/C PERFORMANCE TEST................24-8
A/C RECIRCULATING AIR DOOR
VACUUM MOTOR REPLACEMENT........24-31
ACCELERATION SENSOR INSTALLATION.....5-52
ACCELERATION SENSOR REMOVAL........5-52
ACCELERATION SWITCH.................5-41
ACCELERATION SWITCH OPERATION.......5-45
ACCELERATOR PEDAL..................14-16
ACCELERATOR PEDAL AND THROTTLE
CABLE........................14-16,14-54
ACCENT PAINT.......................23-202
ACCESSORY DRIVE BELT.................0-20
ACCESSORY DRIVE BELTS, ENGINE........7-31
ACCUMULATOR PISTONS AND SPRINGS . . 21-179
ACTUATOR MOTOR STALL TEST...........8P-6
ADAPTER HOUSING AND PARK LOCK
COMPONENT OVERHAUL.............21-120
ADAPTER HOUSING SEAL REPLACEMENT . . 21-182
ADD-A-TRUNK.......................23-199
ADJUSTER PLUG ASSEMBLY
REPLACEMENT......................19-27
ADJUSTMENT, BRAKELIGHT SWITCH.......5-66
ADJUSTMENT, DIFFERENTIAL SHIM
PACK MEASUREMENT..................2-42
ADJUSTMENT, DOOR LATCH
.............23-55
ADJUSTMENT, DRUM BRAKE
..............5-35
ADJUSTMENT, FOG LAMP BEAM
..........8L-12
ADJUSTMENT, FRONT BAND
.............21-99ADJUSTMENT, HEADLAMP BEAM..........8L-3
ADJUSTMENT, HOOD....................23-9
ADJUSTMENT, LIFTGATE................23-70
ADJUSTMENTÐMAJOR, DOOR
ALIGNMENT.........................23-47
ADJUSTMENTÐMINOR, DOOR
ALIGNMENT.........................23-46
ADJUSTMENT, PARK INTERLOCK CABLE . . . 21-186
ADJUSTMENT, PARKING BRAKE...........5-63
ADJUSTMENT, PRELIMINARY
INSPECTION.......................21-167
ADJUSTMENT PROCEDURES,
TRANSMISSION ASSEMBLY...........21-146
ADJUSTMENT, REAR BAND..............21-99
ADJUSTMENT, SHIFT CABLE............21-186
ADJUSTMENT, SHIFT LINKAGE....21-275,21-296
ADJUSTMENT, TAILGATE...............23-160
ADJUSTMENT, TRANSMISSION
ASSEMBLY..............21-15,21-51,21-255
ADJUSTMENT, TRANSMISSION
THROTTLE CABLE..............21-98,21-185
ADJUSTMENT, TRANSMISSION
THROTTLE VALVE CABLE..............21-70
ADJUSTMENT, VALVE BODY ASSEMBLY . . . 21-144
ADJUSTMENT, WHEEL SENSOR AIR GAP....5-49
ADJUSTMENT (XJ), PARK INTERLOCK
CABLE.............................21-97
ADJUSTMENT (XJ), SHIFT CABLE.........21-97
ADJUSTMENT (YJ), GEARSHIFT LINKAGE . . . 21-96
ADJUSTMENTS, ALIGNMENT
MEASUREMENTS......................2-6
ADJUSTMENTS IN VEHICLE, GEAR........19-37
ADJUSTMENTS ON BENCH, GEAR.........19-42
ADJUSTMENTS, SPECIFICATIONS AND
BAND..............................21-66
ADJUSTMENTS, STEERING GEAR.........19-22
AIR CLEANER..........................25-7
AIR CLEANER FILTER ELEMENT, ENGINE....0-16
AIR CLEANER HOUSING; EMISSION
CONTROL SYSTEMS...................25-8
AIR CLEANER HOUSING; FUEL SYSTEM....14-54
AIR CONDITIONER COMPRESSOR/HOSES/
FITTINGS............................0-21
AIR CONDITIONING CLUTCH RELAY.......14-54
AIR CONDITIONING CLUTCH RELAYÐ
PCM OUTPUT.......................14-24
AIR CONDITIONING CONTROLSÐPCM
INPUT.............................14-19
AIR CONDITIONING, DESCRIPTION........24-41
AIR CONDITIONING SCHEMATIC..........24-25
AIR CONDITIONING SYSTEM DIAGNOSIS . . . 24-12
AIR CONDITIONING SYSTEMÐXJ
VEHICLES..........................24-14
AIR CONDITIONING SYSTEMÐYJ
VEHICLES..........................24-15
AIR CONTROL (IAC) MOTOR, IDLE........14-56
AIR CONTROL (IAC) MOTORÐPCM
OUTPUT, IDLE.......................14-25
AIR CONTROL MOTOR TEST, IDLE........14-46
AIR DEFLECTOR, COWL WEATHERSTRIP
SEAL/CROSSMEMBER.................23-10
AIR DOOR VACUUM MOTOR, FRESH.......24-41
AIR DOOR VACUUM MOTOR
REPLACEMENT, A/C RECIRCULATING.....24-31
AIR EXHAUST GRILLEÐXJ VEHICLES......23-30
AIR FILTER; EMISSION CONTROL
SYSTEMS...........................25-9
AIR FILTER; FUEL SYSTEM..............14-54
AIR GAP ADJUSTMENT, WHEEL SENSOR....5-49
AIR GAP, REAR SPEED SENSOR............5-3
AIR INTAKE DUCT, FRESH...............24-41
AIR PRESSURE TEST...................21-73
AIR, PURGING COMPRESSOR OF.........24-17
AIR TEMPERATURE SENSOR, INTAKE......14-54
AIR TEMPERATURE SENSOR, INTAKE
MANIFOLD.....................8D-5,8D-27
AIR TEMPERATURE SENSORÐPCM
INPUT, INTAKE.......................14-20
AIR TEMPERATURE, SENSOR RESISTANCE
(OHMS)ÐCOOLANT TEMPERATURE
SENSOR/MANIF; FUEL SYSTEM
.........14-43
AIR TEMPERATURE SENSOR TEST,
INTAKE
............................14-43
AIR TEMPERATURE SENSOR TEST,
INTAKE MANIFOLD
...................8D-14
AIR VENTILATION, FRESH
...............24-39AIRFLOW DIAGRAM....................24-23
ALIGNMENT ADJUSTMENTÐMAJOR,
DOOR.............................23-47
ALIGNMENT ADJUSTMENTÐMINOR,
DOOR.............................23-46
ALIGNMENT, FRAME...................13-10
ALIGNMENT, FRONT WHEEL...............2-5
ALIGNMENT, HOOD...................23-138
ALIGNMENT MEASUREMENTS AND
ADJUSTMENTS........................2-6
ALIGNMENTÐMINOR, XJ DOOR..........23-46
ALIGNMENT, REAR AXLE..................3-8
ALIGNMENT SPECIFICATIONSÐXJ
VEHICLES............................2-9
ALIGNMENT SPECIFICATIONSÐYJ VEHICLES . . 2-9
ANALYSIS, BACKLASH AND CONTACT
PATTERN; FRONT SUSPENSION AND AXLE . 2-44
ANALYSIS, BACKLASH AND CONTACT
PATTERN; REAR SUSPENSION AND AXLES . 3-25
ANCHOR AND BUMPER, LIFTGATE
LICENSE PLATE SCREW...............23-72
ANGLE MEASUREMENT, UNIVERSAL
JOINT..............................16-4
ANTENNA, RADIO.......................8F-8
ANTENNA TESTS.......................8F-9
ANTILOCK BRAKE SYSTEM (ABS)...........5-1
ANTI-LOCK BRAKE SYSTEM (ABS)
INDICATOR LAMP.....................8E-2
ANTILOCK BRAKE SYSTEM OPERATION.....5-43
ANTILOCK BRAKING MODE, ABS
OPERATION..........................5-43
ANTI-LOCK INDICATOR..................8E-4
ANTILOCK MODE, VEHICLE RESPONSE.......5-3
APPLICATION CHARTS, GEARTRAIN
OPERATION........................21-159
APPLICATION, PAINT..................23-201
APPLICATION, TRANSMISSION...........21-66
APPLIQUE, RADIATOR GRILLE
...........23-134
APPLIQUEÐXJ VEHICLES, QUARTER
WINDOW
...........................23-29
APRONS, FENDER SPLASH
.............23-147
ARM AND PIVOT ASSEMBLY
REPLACEMENT, FRONT WIPER
...........8K-9
ARM, LOWER SUSPENSION
...............2-11
ARM, PITMAN
...................19-15,19-18
ARM REPLACEMENT, FRONT WIPER
........8K-8
ARM REPLACEMENT, REAR WIPER
........8K-12
ARM, UPPER SUSPENSION
...............2-11
ARMS, ROCKER
....................9-19,9-59
ASH RECEIVER TRAY LAMP, I/P
..........23-92
ASSEMBLY AND ADJUSTMENT
PROCEDURES, TRANSMISSION
........21-146
ASSEMBLY AND ADJUSTMENT,
TRANSMISSION
..........21-15,21-51,21-255
ASSEMBLY AND ADJUSTMENT, VALVE
BODY
.............................21-144
ASSEMBLY, CALIPER
....................5-29
ASSEMBLY, DIFFERENTIAL; FRONT
SUSPENSION AND AXLE
................2-36
ASSEMBLY, DIFFERENTIAL; REAR
SUSPENSION AND AXLES
...............3-19
ASSEMBLY, FINAL; FRONT SUSPENSION
AND AXLE
...........................2-44
ASSEMBLY, FINAL; REAR SUSPENSION
AND AXLES
..........................3-26
ASSEMBLY, FUEL RAIL
..................14-56
ASSEMBLY, GEAR
......................19-41
ASSEMBLY, PRESSURE GAUGE AND
MANIFOLD
...........................24-2
ASSEMBLY REPLACEMENT, ADJUSTER
PLUG
..............................19-27
ASSEMBLY REPLACEMENT, CONNECTOR
AND TERMINAL
......................8W-5
ASSEMBLY REPLACEMENT, FRONT WIPER
ARM AND PIVOT
......................8K-9
ASSEMBLY REPLACEMENT, SOLENOID
AND LATCH
..........................8P-6
ASSEMBLY REPLACEMENTÐXJ VEHICLES,
DRIVE AXLE; FRONT SUSPENSION AND
AXLE
...............................2-21
ASSEMBLY REPLACEMENTÐXJ VEHICLES,
DRIVE AXLE; REAR SUSPENSION AND
AXLES
..........................3-11,3-30
JINDEX1
Description Group-Page Description Group-Page Description Group-Page

COLD CRANKING TEST, STARTING
SYSTEM............................8A-9
COLLISION DAMAGE TORQUE.............13-1
COLORS, EXTERIOR BODY..............23-204
COLUMN GENERAL SERVICE, STEERING . . . 19-45
COLUMN, NON-TILT STEERING...........19-50
COLUMN REPLACEMENTÐXJ............19-46
COLUMN REPLACEMENTÐYJ............19-48
COLUMN, TILT STEERING...............19-59
COLUMNÐXJ, STEERING...............19-73
COLUMNÐYJ, STEERING...............19-73
COMBINATION VALVE................5-15,5-42
COMBINATION VALVE REPLACEMENTÐXJ . . . 5-55
COMBINATION VALVE REPLACEMENTÐYJ . . . 5-55
COMBUSTION PRESSURE LEAKAGE
TEST, CYLINDER.......................9-6
COMBUSTION PRESSURE LEAKAGE
TEST DIAGNOSIS, CYLINDER.............9-6
COMPASS REPAIR PROCEDURES..........8C-4
COMPENSATION, CALIPER OPERATION
AND WEAR..........................5-24
COMPRESSION PRESSURE TEST,
CYLINDER............................9-5
COMPRESSOR........................24-17
COMPRESSOR DIAGNOSIS..............24-13
COMPRESSOR ISOLATION...............24-17
COMPRESSOR OF AIR, PURGING.........24-17
COMPRESSOR OIL LEVEL................24-6
COMPRESSOR OVERHAUL...............24-17
COMPRESSOR VALVE PLATEÐLEAK
TESTS..............................24-8
COMPRESSOR/HOSES/FITTINGS, AIR-
CONDITIONER........................0-21
CONDENSERÐ4.0L ENGINES............24-32
CONDENSER, A/C......................24-42
CONDENSER/RECEIVER DRIERÐ2.5L
ENGINES...........................24-31
CONDITION, CHECKING FLUID LEVEL......21-96,
21-173
CONDITION, FLUID LEVEL...............21-69
CONDITIONING CLUTCH RELAY, AIR.......14-54
CONDITIONING CLUTCH RELAYÐPCM
OUTPUT, AIR........................14-24
CONDITIONING CONTROLSÐPCM INPUT,
AIR ...............................14-19
CONDITIONING SCHEMATIC, AIR..........24-25
CONDITIONING SYSTEM DIAGNOSIS,
AIR ...............................24-12
CONDITIONING SYSTEMÐXJ VEHICLES,
AIR ...............................24-14
CONDITIONING SYSTEMÐYJ VEHICLES,
AIR ...............................24-15
CONNECTING ROD BEARING FITTING
CHART..........................9-36,9-76
CONNECTING RODS, PISTONS........9-34,9-74
CONNECTIONS, STARTER RELAY..........8A-12
CONNECTOR AND TERMINAL ASSEMBLY
REPLACEMENT.......................8W-5
CONNECTORÐPCM INPUT, DATA LINK.....14-20
CONNECTORÐPCM OUTPUT, DATA LINK . . . 14-24
CONNECTOR PINS, RADIO................8F-3
CONNECTOR, POWERTRAIN CONTROL
MODULE (PCM) 60-WAY...............14-38
CONNECTOR REPLACEMENT.............8W-4
CONNECTORS.........................8W-3
CONSOLE, OVERHEAD...................8A-1
CONSOLE REPAIR PROCEDURES..........8C-6
CONSOLE SHIFT, DISASSEMBLYÐ
COLUMN OR
........................19-50
CONSOLEÐXJ VEHICLES, FULL FLOOR
. . . 23-125
CONSOLEÐXJ VEHICLES, MINI-FLOOR
....23-124
CONSOLEÐXJ VEHICLES, OVERHEAD
......8L-20
CONSOLES, FLOOR
...................23-197
CONSTRUCTION, XJ UNIBODY
.............13-1
CONTACT PATTERN ANALYSIS,
BACKLASH AND; FRONT SUSPENSION
AND AXLE
...........................2-44
CONTACT PATTERN ANALYSIS, BACKLASH
AND; REAR SUSPENSION AND AXLES
.....3-25
CONTAMINATION, BRAKE FLUID
...........5-13
CONTINUITY TESTS, IGNITION SWITCH
....8D-31
CONTROL AND DISPLAY SYMBOLS,
INTERNATIONAL VEHICLE
...........INTRO.-3
CONTROL AND DISPLAY SYMBOLS,
VEHICLE
.........................INTRO.-7CONTROL CABLE REPLACEMENT,
HEATER ............................24-30
CONTROL CABLES, VENT DOOR..........24-39
CONTROL CIRCUIT TESTS, STARTER......8A-11
CONTROL, FUEL PUMP ELECTRICAL........14-5
CONTROL (IAC) MOTOR, IDLE AIR........14-56
CONTROL (IAC) MOTORÐPCM OUTPUT,
IDLE AIR...........................14-25
CONTROL INFORMATION (VECI)
LABEL, VEHICLE WINDOW..............25-1
CONTROL MODULE, ELECTRICAL TESTS
AT POWERTRAIN.....................8H-6
CONTROL MODULE (PCM) 60-WAY
CONNECTOR, POWERTRAIN............14-38
CONTROL MODULE (PCM), POWERTRAIN;
EMISSION CONTROL SYSTEMS..........25-9
CONTROL MODULE (PCM), POWERTRAIN;
FUEL SYSTEM..................14-18,14-58
CONTROL MODULE (PCM), POWERTRAIN;
IGNITION SYSTEMS.........8D-6,8D-15,8D-28
CONTROL MODULE (TCM) SERVICE,
TRANSMISSION.....................21-173
CONTROL MOTOR TEST, IDLE AIR........14-46
CONTROL PANEL, A/C..................24-41
CONTROL PANEL REPLACEMENT,
HEATER ............................24-39
CONTROL PANEL REPLACEMENT,
HEATER AND A/C ....................24-26
CONTROLÐPCM INPUT, SPEED..........14-23
CONTROLÐPCM OUTPUT, SPEED.........14-27
CONTROL SERVO REPLACEMENT, SPEED....8H-9
CONTROL SWITCH REPLACEMENT,
SPEED..............................8H-9
CONTROL SWITCH REPLACEMENT,
WIPER.............................8K-15
CONTROL SWITCH TEST, STOP LAMP
SPEED..............................8H-7
CONTROL SWITCH (TURN SIGNAL
LEVER) TEST, SPEED..................8H-7
CONTROL SYSTEM ELECTRICAL TESTS,
VEHICLE SPEED......................8H-5
CONTROL SYSTEM, EVAP (EVAPORATION)....25-4
CONTROL SYSTEM, VEHICLE SPEED........8A-1
CONTROL SYSTEMÐXJ VEHICLES,
CLIMATE...........................24-22
CONTROL SYSTEMÐYJ VEHICLES,
CLIMATE...........................24-37
CONTROL THERMOSTAT, TEMPERATURE....24-35
CONTROL UNIT (ECU), ELECTRONIC........5-41
CONTROL UNIT (HCU), HYDRAULIC........5-39
CONTROL VALVE FITTING O-RING SEAL,
FLOW..............................19-12
CONTROLS AND COMPONENTS,
TRANSMISSION......................21-66
CONTROLS, EVAPORATIVE EMISSION.......25-4
CONTROLS, EXHAUST EMISSION..........25-7
CONTROLSÐPCM INPUT, AIR
CONDITIONING (A/C)..................14-19
CONTROLSÐXJ VEHICLES, BLOWER......24-14
CONVERSION FORMULAS AND
EQUIVALENT VALUES..............INTRO.-8
CONVERSION, TORQUE..............INTRO.-10
CONVERTER, CATALYTIC.............11-1,11-5
CONVERTER CLUTCH ENGAGED,
HYDRAULIC FLOW IN THIRD GEAR......21-90
CONVERTER CLUTCH RELAY.............14-60
CONVERTER CLUTCH RELAY TEST........14-45
CONVERTER CLUTCH RELAYÐPCM
OUTPUT............................14-27
CONVERTER HOUSING LEAK
DIAGNOSIS.........................21-73
CONVERTER INSTALLATION,
TRANSMISSION.....................21-109
CONVERTER INSTALLATION,
TRANSMISSION AND TORQUE.........21-190
CONVERTERÐPUMP SEALÐDRIVE
PLATE SERVICE.....................21-109
CONVERTER REMOVAL, TRANSMISSION . . . 21-108
CONVERTER REMOVAL, TRANSMISSION
AND TORQUE......................21-189
CONVERTER STALL TEST
................21-72
CONVERTER STALL TEST, TORQUE
.......21-169
CONVERTER STATOR CLUTCH
INSPECTION, TORQUE
................21-189
CONVERTER, TORQUE; TRANSMISSION
AND TRANSFER CASE
...........21-66,21-158CONVERTER/MUFFLER/TAILPIPE
SUPPORT BRACKETS, CATALYTIC........23-85
COOLANT.............................7-15
COOLANT RESERVE/OVERFLOW
SYSTEM............................7-19
COOLANT ROUTING, SYSTEM..............7-1
COOLANT TEMPERATURE GAUGE..........8E-1
COOLANT TEMPERATURE GAUGE
INOPERATIVE........................8E-3
COOLANT TEMPERATURE INDICATOR
INOPERATIVE........................8E-3
COOLANT TEMPERATURE INDICATOR
LAMP...............................8E-1
COOLANT TEMPERATURE SENSOR.........25-9
COOLANT TEMPERATURE SENSOR,
ENGINE; FUEL SYSTEM................14-55
COOLANT TEMPERATURE SENSOR,
ENGINE; IGNITION SYSTEMS
.......8D-4,8D-22
COOLANT TEMPERATURE SENSORÐ
PCM INPUT, ENGINE
..................14-21
COOLANT TEMPERATURE SENSOR TEST,
ENGINE; FUEL SYSTEM
................14-43
COOLANT TEMPERATURE SENSOR TEST,
ENGINE; IGNITION SYSTEMS
...........8D-12
COOLER FLOW TESTING, TRANSMISSION
. . 21-106
COOLER LINE FITTINGS, TRANSMISSION
. . 21-187
COOLER LINES AND FITTINGS,
SERVICING TRANSMISSION
...........21-106
COOLER REVERSE FLUSHING,
TRANSMISSION
.....................21-105
COOLER SERVICE, TRANSMISSION
.......21-187
COOLERS, TRANSMISSION OIL
............7-29
COOLING SYSTEM; COOLING SYSTEM
.......7-1
COOLING SYSTEM; LUBRICATION AND
MAINTENANCE
.......................0-16
COOLING SYSTEM CAPACITIES
............7-38
COOLING SYSTEM CLEANING/REVERSE
FLUSHING
...........................7-17
COOLING SYSTEM COMPONENTS
...........7-1
COOLING SYSTEM, DRAINING
.............7-16
COOLING SYSTEM FANS
.................7-26
COOLING SYSTEM FOR LEAKS, TESTING
....7-18
COOLING SYSTEM HOSES
................7-26
COOLING SYSTEM, REFILLING
............7-17
CORE AND HOUSING, HEATER
............24-40
CORE, HEATER
........................24-28
CORE HOUSING REPLACEMENT, HEATER
. . . 24-29
COVER AND DISC INSTALLATION,
CLUTCH
.............................6-10
COVER AND DISC REMOVAL, CLUTCH
......6-10
COVER AND FRAME, BUCKET SEATBACK
. . 23-100
COVER, BUCKET SEAT CUSHION
..........23-98
COVER, ENGINE CYLINDER HEAD
......9-18,9-59
COVER, FRAME CROSSMEMBER
..........13-14
COVER OIL SEAL REPLACEMENT,
TIMING CASE
....................9-26,9-67
COVER REPLACEMENT, PITMAN SHAFT
AND SIDE
..........................19-26
COVER, TIMING CASE
...............9-27,9-67
COVERÐXJ VEHICLES, REAR SEAT
CUSHION
..........................23-107
COVERÐXJ VEHICLES, REAR
SEATBACK
.........................23-111
COVERSÐXJ VEHICLES, B/C-PILLAR AND
LIFTGATE PILLAR TRIM
..............23-116
COWL GRILLE AND SCREEN
.......23-11,23-139
COWL WEATHERSTRIP SEAL
............23-139
COWL WEATHERSTRIP SEAL/
CROSSMEMBER AIR DEFLECTOR
........23-10
CRANKCASE VENTILATION SYSTEM;
EMISSION CONTROL SYSTEMS
..........25-5
CRANKCASE VENTILATION SYSTEM;
LUBRICATION AND MAINTENANCE
........0-17
CRANKING TEST, STARTING SYSTEM
COLD
...............................8A-9
CRANKSHAFT MAIN BEARINGS;
ENGINES
........................9-40,9-80
CRANKSHAFT POSITION SENSOR;
FUEL SYSTEM
.......................14-55
CRANKSHAFT POSITION SENSOR;
IGNITION SYSTEMS
..............8D-2,8D-21
JINDEX5
Description Group-Page Description Group-Page Description Group-Page

DRIVE GEAR, SPEED SENSOR ROTORÐ
SPEEDOMETER.....................21-183
DRIVE, GENERATOR REPLACEMENTÐ
LEFT HAND..........................8B-7
DRIVE, GENERATOR
REPLACEMENTÐRIGHT HAND...........8B-9
DRIVE PULLEY REPLACEMENT...........19-11
DRIVE (RHD), BELT TENSIONÐEXCEPT
RIGHT HAND.........................7-33
DRIVE (RHD), BELT TENSIONÐRIGHT
HAND...............................7-34
DRIVE SHAFTS.........................0-27
DRIVE VEHICLES, RIGHT HAND............23-1
DRIVE, WASHER PUMP REPLACEMENTÐ
LEFT HAND..........................8K-2
DRIVE, WASHER PUMP REPLACEMENTÐ
RIGHT HAND.........................8K-3
DRIVELINE SNAP; FRONT SUSPENSION
AND AXLE...........................2-17
DRIVELINE SNAP; REAR SUSPENSION
AND AXLES...........................3-8
DRIVELINE VIBRATION...................16-3
DRIVER SIDE..........................8R-2
DRIVERS DOOR POWER LOCK SWITCHÐ
2-DOOR LEFT HAND DRIVE.............8P-2
DRIVERS DOOR POWER LOCK SWITCHÐ
2-DOOR RIGHT HAND DRIVE............8P-3
DRIVERS DOOR POWER LOCK SWITCHÐ
4-DOOR.............................8P-4
DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR LEFT HAND DRIVE.....8S-6
DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR RIGHT HAND DRIVE....8S-7
DRIVERS DOOR POWER WINDOW
SWITCHÐ4-DOOR....................8S-5
DRIVETRAIN...........................0-22
DRL MODULE REPLACEMENT............8L-16
DRUM BRAKE ADJUSTMENT..............5-35
DRUM BRAKES........................5-34
DRUM BRAKESHOE INSTALLATION.........5-34
DRUM BRAKESHOE REMOVAL.............5-34
DRUM REFINISHING, BRAKE..............5-37
DRUMÐREAR SUPPORT OVERHAUL,
OVERRUNNING CLUTCHÐLOW-
REVERSE..........................21-118
DUCT, DEFROSTER NOZZLE..............24-40
DUCT, FRESH AIR INTAKE...............24-41
DUCT REPLACEMENT, DEFROSTER........24-29
DUCTS/HOSES/TUBING, RUBBER AND
PLASTIC............................0-19
ECU DIAGNOSIS.........................5-4
ECU OPERATION.......................5-46
ECU REPLACEMENTÐXJ.................5-53
ECU REPLACEMENTÐYJ.................5-53
EDGE GUARD/EDGE PROTECTOR STRIP,
DOOR.............................23-61
ELECTRICAL CIRCUITS, ABS SYSTEM
WIRING..............................5-4
ELECTRICAL CONTROL, FUEL PUMP........14-5
ELECTRICAL TESTS AT POWERTRAIN
CONTROL MODULE...................8H-6
ELECTRICAL TESTS AT SERVO............8H-5
ELECTRICAL TESTS, VEHICLE SPEED
CONTROL SYSTEM....................8H-5
ELECTRONIC CONTROL UNIT (ECU)........5-41
ELEMENT, ENGINE AIR CLEANER FILTER....0-16
ELEMENT TEST, OXYGEN SENSOR (O2S)
HEATING...........................14-45
EMISSION CONTROL INFORMATION
(VECI) LABEL, VEHICLE.................25-1
EMISSION CONTROLS, EVAPORATIVE.......25-4
EMISSION CONTROLS, EXHAUST..........25-7
EMR LAMPÐPCM OUTPUT..............14-24
END PLUG, HOUSING...................19-26
ENGINE ACCESSORY DRIVE BELTS.........7-31
ENGINE AIR CLEANER FILTER ELEMENT.....0-16
ENGINE AND TRANSMISSION/TRANSFER
CASE IDENTIFICATION..............INTRO.-3
ENGINE ASSEMBLY (SHORT BLOCK),
SERVICE.............................9-4
ENGINE ASSEMBLYÐXJ VEHICLES;
ENGINES
........................9-14,9-54
ENGINE ASSEMBLYÐYJ VEHICLES;
ENGINES
........................9-16,9-57
ENGINE BLOCK HEATER
..................7-37
ENGINE BREAK-IN
......................0-13ENGINE COOLANT TEMPERATURE
SENSOR; FUEL SYSTEM...............14-55
ENGINE COOLANT TEMPERATURE
SENSOR; IGNITION SYSTEMS......8D-4,8D-22
ENGINE COOLANT TEMPERATURE
SENSORÐPCM INPUT................14-21
ENGINE COOLANT TEMPERATURE
SENSOR TEST; FUEL SYSTEM..........14-43
ENGINE COOLANT TEMPERATURE
SENSOR TEST; IGNITION SYSTEMS......8D-12
ENGINE CYLINDER HEAD.............9-19,9-60
ENGINE CYLINDER HEAD COVER......9-18,9-59
ENGINE CYLINDER HEAD GASKET
FAILURE DIAGNOSIS....................9-5
ENGINE DAMPER.......................9-13
ENGINE DIAGNOSIS......................9-5
ENGINE, ENGINE EXHAUST MANIFOLDÐ
2.5L................................11-7
ENGINE, ENGINE EXHAUST MANIFOLDÐ
4.0L................................11-7
ENGINE, ENGINE FIRING ORDERÐ2.5L....8D-33
ENGINE, ENGINE FIRING ORDERÐ4.0L....8D-33
ENGINE EXHAUST MANIFOLDÐ2.5L
ENGINE.............................11-7
ENGINE EXHAUST MANIFOLDÐ4.0L
ENGINE.............................11-7
ENGINE FIRING ORDERÐ2.5L ENGINE.....8D-33
ENGINE FIRING ORDERÐ4.0L ENGINE.....8D-33
ENGINE FRONT SUPPORT CUSHION.......13-15
ENGINE, INTAKE MANIFOLDÐ2.5L.........11-8
ENGINE, INTAKE MANIFOLDÐ4.0L.........11-9
ENGINE MAINTENANCE..................0-13
ENGINE MOUNTÐREAR.............9-12,9-52
ENGINE MOUNTSÐFRONT...........9-10,9-51
ENGINE OIL...........................0-13
ENGINE OIL CHANGE AND FILTER
REPLACEMENT.......................0-15
ENGINE OIL FILTER.....................0-14
ENGINE ONLY, POWER STEERING
PRESSURE SWITCHÐ2.5L.............14-58
ENGINE PERFORMANCE...................9-2
ENGINE SERVICE PROCEDURES, 2.5L........9-9
ENGINE SERVICE PROCEDURES, 4.0L.......9-50
ENGINE SPECIFICATIONS....9-47,9-87,9-48,9-49,
9-88,9-89
ENGINE STARTER MOTOR SERVICE
PROCEDURES........................8B-4
ENGINE STARTER MOTOR TEST
PROCEDURES ON VEHICLE.............8A-9
ENGINE SUPPORTS.....................0-20
ENGINE, VACUUM ROUTING
SCHEMATICÐ2.5L 4 CYLINDER..........25-2
ENGINE, VACUUM ROUTING
SCHEMATICÐ4.0L 6 CYLINDER..........25-3
ENGINES, 2.5L........................8B-11
ENGINES, 4.0L........................8B-11
ENGINES, CONDENSERÐ4.0L............24-32
ENGINES, CONDENSER/RECEIVER
DRIERÐ2.5L........................24-31
ENGINES, FUEL USAGE STATEMENTÐ
GAS................................0-17
ENGINES, RECEIVER DRIERÐ4.0L........24-32
ENTRY, KEYLESS.......................8P-8
ENTRY SYSTEM SERVICE INFORMATION,
ILLUMINATED.......................8L-20
ENTRY SYSTEM TROUBLE DIAGNOSIS,
ILLUMINATED..................8L-21,8L-22
EQUIVALENT VALUES, CONVERSION
FORMULAS......................INTRO.-8
EVACUATION, SYSTEM...................24-4
EVAP CANISTER....................25-4,25-9
EVAP (EVAPORATION) CONTROL SYSTEM
....25-4
EVAPORATIVE EMISSION CONTROLS
.......25-4
EVAPORATOR AND HOUSING
.............24-42
EVAPORATOR COIL
....................24-34
EVAPORATOR/BLOWER HOUSING
.........24-33
EXHAUST EMISSION CONTROLS
...........25-7
EXHAUST GRILLEÐXJ VEHICLES, AIR
.....23-30
EXHAUST HEAT SHIELDS
.................11-1
EXHAUST MANIFOLDÐ2.5L ENGINE,
ENGINE
.............................11-7
EXHAUST MANIFOLDÐ4.0L ENGINE,
ENGINE
.............................11-7
EXHAUST PIPEÐXJ VEHICLES
............11-3
EXHAUST PIPEÐYJ VEHICLES
............11-4EXHAUST SYSTEM; EXHAUST SYSTEM
AND INTAKE MANIFOLD................11-1
EXHAUST SYSTEM; LUBRICATION AND
MAINTENANCE.......................0-20
EXHAUST SYSTEM DIAGNOSIS............11-2
EXHAUST TAILPIPEÐXJ VEHICLES,
MUFFLER............................11-5
EXHAUST TAILPIPEÐYJ VEHICLES,
MUFFLER............................11-6
EXPANSION (H) VALVE.............24-35,24-43
EXTENDED IDLE SWITCHÐPCM INPUT....14-21
EXTENDED IDLE SWITCH TEST...........14-45
EXTENSION PANELÐYJ RENEGADE
VEHICLES, FRONT FENDER............23-149
EXTENSION PANELÐYJ RENEGADE
VEHICLES, REAR QUARTER...........23-151
EXTENSION PANELÐYJ RENEGADE
VEHICLES, ROCKER.................23-150
EXTENSION PANELS AND FASCIASÐYJ
RENEGADE VEHICLES, BODY..........23-147
EXTENSIONÐXJ VEHICLES, QUARTER
TRIM PANEL.......................23-115
EXTERIOR BODY COLORS..............23-204
EXTERIOR COMPONENTS..........23-3,23-134
EXTERIOR LAMPS......................8L-1
EXTERIOR LAMPS, XJ..................8L-23
EXTERIOR LAMPS, YJ..................8L-23
EXTERIOR MOULDINGS, DOOR WINDOW . . . 23-61
EXTERIOR NAMEPLATES................23-30
EXTERIOR NAMEPLATES (ADHESIVE-
BACKED)..........................23-158
EXTERIOR PAINT CODES, XJ............23-205
EXTERIOR PAINT CODES, YJ............23-206
EXTERNAL HANDLE, DOOR..............23-55
EXTERNAL MIRRORS...................23-31
EXTERNAL RELEASE HANDLE, FULL-
METAL DOOR LATCH.................23-178
EXTERNAL SPARE/WHEEL TIRE CARRIER . . 23-172
EYE BUSHING REPLACEMENT, LEAF
SPRING; FRONT SUSPENSION
AND AXLE...........................2-15
EYE BUSHING REPLACEMENT, LEAF
SPRING; REAR SUSPENSION
AND AXLES........................3-4,3-6
FAILURE DIAGNOSIS, ENGINE CYLINDER
HEAD GASKET.........................9-5
FAN RELAYÐPCM OUTPUT, RADIATOR.....14-26
FANS, COOLING SYSTEM.................7-26
FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES, FRONT.........23-148
FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES, REAR..........23-152
FASCIASÐYJ RENEGADE VEHICLES,
BODY EXTENSION PANELS............23-147
FAULT DIAGNOSIS, ABS................5-4,5-6
FEED CIRCUIT TESTS - (VOLTAGE DROP
METHOD), STARTER...................8A-9
FENDER EXTENSION PANELÐYJ
RENEGADE VEHICLES, FRONT.........23-149
FENDER FLARE.......................23-144
FENDER, FRONT.......................23-14
FENDER INNER SPLASH SHIELDS........23-147
FENDER SPLASH APRONS..............23-147
FENDERS...........................23-141
FIELDÐPCM OUTPUT, GENERATOR.......14-25
FILL LEVEL, TRANSFER CASE...........21-294
FILLER DOOR BUMPERS, FUEL...........23-31
FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES, FUEL.....................23-86
FILLER NOZZLE/TUBE, FUEL
.............23-30
FILLER PROTECTOR/NOZZLE, FUEL
.......23-158
FILLER TUBE CAP, FUEL TANK;
EMISSION CONTROL SYSTEMS
......25-4,25-9
FILLER TUBE CAP, FUEL TANK; FUEL
SYSTEM
............................14-12
FILLER TUBE, NO-LEAD FUEL TANK
.......14-12
FILTER, AIR; EMISSION CONTROL
SYSTEMS
...........................25-9
FILTER, AIR; FUEL SYSTEM
..............14-54
FILTER BRACKET, FUEL
.................23-86
FILTER ELEMENT, ENGINE AIR CLEANER
....0-16
FILTER, ENGINE OIL
.....................0-14
FILTER, FUEL
.....................14-8,14-55
FILTER REPLACEMENT, ENGINE
OIL CHANGE
.........................0-15
8 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

FUSES AND ABBREVIATIONS, SYMBOLS, . . . 8W-6
FUSIBLE LINK REPLACEMENT............8W-4
FUSIBLE LINKS........................8W-3
GALVANIZED METALS, PAINT REPAIR ON . . 23-202
GAP ADJUSTMENT, WHEEL SENSOR AIR....5-49
GAP, REAR SPEED SENSOR AIR............5-3
GASKET FAILURE DIAGNOSIS, ENGINE
CYLINDER HEAD.......................9-5
GASKETS, FORM-IN-PLACE................9-1
GAUGE AND MANIFOLD ASSEMBLY,
PRESSURE..........................24-2
GAUGE CALIBRATION VALUES............8E-22
GAUGE CLUSTER REPLACEMENT.........8E-24
GAUGE, COOLANT TEMPERATURE..........8E-1
GAUGE, FUEL..........................8E-2
GAUGE HOUSINGS, INSTRUMENT
CLUSTER..........................23-190
GAUGE INOPERATIVE, COOLANT
TEMPERATURE.......................8E-3
GAUGE INOPERATIVE, FUEL...............8E-3
GAUGE INOPERATIVE, OIL PRESSURE......8E-3
GAUGE INOPERATIVE, ONE..............8E-22
GAUGE, OIL PRESSURE..................8E-1
GAUGE PACKAGE DIAGNOSIS............8E-22
GAUGE PACKAGE GAUGE REPLACEMENT . . . 8E-24
GAUGE PACKAGE GENERAL
INFORMATION.......................8E-22
GAUGE PACKAGE SERVICE PROCEDURES . . . 8E-24
GAUGE REPLACEMENT, GAUGE
PACKAGE...........................8E-24
GAUGE REPLACEMENTÐINSTRUMENT
CLUSTER REMOVED...................8E-5
GAUGE SENDING UNIT, FUEL.............14-15
GAUGES AND INDICATORS INOPERATIVE....8E-3
GAUGES INOPERATIVE (FIG. 15), ALL......8E-22
GAUGES, INSTRUMENT CLUSTER;
INSTRUMENT PANEL AND GAUGESÐ
XJ ................................8E-13
GAUGES, INSTRUMENT CLUSTER;
INSTRUMENT PANEL AND GAUGESÐ
YJ ................................8E-27
GAUGES, INSTRUMENT PANEL......8A-1 ,8E-27
GAUGES, PRESSURE....................22-2
GAUGESÐXJ, INSTRUMENT PANEL........8E-1
GAUGESÐYJ, INSTRUMENT PANEL........8E-1
GEAR (1) POSITION, HYDRAULIC FLOW
IN MANUAL FIRST...................21-94
GEAR ADJUSTMENTS IN VEHICLE.........19-37
GEAR ADJUSTMENTS ON BENCH.........19-42
GEAR ADJUSTMENTS, STEERING.........19-22
GEAR AND BEARING NOISE; FRONT
SUSPENSION AND AXLE................2-16
GEAR AND BEARING NOISE; REAR
SUSPENSION AND AXLES................3-7
GEAR AND CLUTCH OVERHAUL,
OVERDRIVE PLANETARY..............21-209
GEAR AND NO. 1 ONE-WAY CLUTCH
OVERHAUL, SUN....................21-229
GEAR ASSEMBLY, STEERING.............19-41
GEAR ASSEMBLY/INSTALLATION,
PINION; FRONT SUSPENSION AND AXLE....2-40
GEAR ASSEMBLY/INSTALLATION,
PINION; REAR SUSPENSION AND AXLES....3-22
GEAR CLEANING AND INSPECTION........19-40
GEAR COMPONENTS, FIRSTÐTHIRDÐ
REVERSE..........................21-159
GEAR (CONVERTER CLUTCH
ENGAGED), HYDRAULIC FLOW IN
THIRD.............................21-90
GEAR DEPTH INFORMATION, PINION;
FRONT SUSPENSION AND AXLE..........2-37
GEAR DEPTH INFORMATION, PINION;
REAR SUSPENSION AND AXLES..........3-19
GEAR DEPTH VARIANCE, PINION; FRONT
SUSPENSION AND AXLE................2-38
GEAR DEPTH VARIANCE, PINION; REAR
SUSPENSION AND AXLES...........3-20,3-38
GEAR DISASSEMBLY INFORMATION.......19-24
GEAR, HYDRAULIC FLOW IN D RANGE
FIRST..............................21-87
GEAR, HYDRAULIC FLOW IN D RANGE
SECOND
............................21-88
GEAR, HYDRAULIC FLOW IN D
RANGE THIRD
.......................21-89
GEAR INSTALLATION, RING
...............3-24
GEAR LEAKAGE DIAGNOSIS
..............19-8GEAR, MANUAL STEERING.........19-35,19-73
GEAR OVERDRIVE COMPONENTS,
FOURTH...........................21-158
GEAR OVERHAUL, FRONT PLANETARY....21-228
GEAR OVERHAUL, GOVERNOR AND
PARK .............................21-121
GEAR, POWER STEERING...............19-73
GEAR RATIOS..........................21-2
GEAR RATIOS, TRANSMISSION...........21-33
GEAR, RECIRCULATING BALL POWER
STEERING..........................19-19
GEAR REPLACEMENT, STEERING....19-21,19-43
GEAR SELECTOR INDICATOR
REPLACEMENTÐINSTRUMENT
CLUSTER REMOVED...................8E-6
GEAR SERVICE, GOVERNOR AND PARK . . . 21-101
GEAR SPECIFICATIONS, MANUAL
STEERING..........................19-44
GEAR SPECIFICATIONS, POWER
STEERING..........................19-34
GEAR, SPEED SENSOR ROTORÐ
SPEEDOMETER DRIVE...............21-183
GEAR TRAIN OVERHAUL, PLANETARY.....21-131
GEARÐYJ VEHICLES, MANUAL
STEERING...........................0-32
GEARS, RECIRCULATING-BALL
POWER STEERING...................19-69
GEARSHIFT LINKAGE...................21-70
GEARSHIFT LINKAGE ADJUSTMENT (YJ) . . . 21-96
GEARTRAIN OPERATION AND
APPLICATION CHARTS...............21-159
GENERAL; BATTERY/STARTER/
GENERATOR SERVICE..................8B-7
GENERAL BODY SERVICE INFORMATION....23-1
GENERAL; CHIME/BUZZER WARNING
SYSTEMS...........................8U-1
GENERAL DIAGNOSIS INFORMATION;
CLUTCH..............................6-3
GENERAL DIAGNOSIS INFORMATION;
TRANSMISSION AND TRANSFER
CASE.............................21-167
GENERAL; HEATING AND AIR
CONDITIONING.......................24-8
GENERAL INFORMATION, 2.5L STARTER....8B-4
GENERAL INFORMATION, 4.0L STARTER....8B-6
GENERAL INFORMATION; AUDIO
SYSTEMS........................8F-1,8F-8
GENERAL INFORMATION, BATTERY
TESTING............................8A-3
GENERAL INFORMATION; BATTERY/
STARTER/GENERATOR SERVICE......8B-1,8B-4
GENERAL INFORMATION; BRAKES . . . 5-1,5-7,5-24,
5-39,5-65
GENERAL INFORMATION; CLUTCH..........6-1
GENERAL INFORMATION; COOLING
SYSTEM.................7-1,7-31,7-37,7-38
GENERAL INFORMATION; ELECTRICAL . 8A-1,8A-2,
8A-8,8A-9,8A-14
GENERAL INFORMATION; EMISSION
CONTROL SYSTEMS...................25-1
GENERAL INFORMATION; ENGINES......9-9,9-50
GENERAL INFORMATION; EXHAUST
SYSTEM AND INTAKE MANIFOLD.........11-1
GENERAL INFORMATION; FRAME AND
BUMPERS.......................13-1,13-8
GENERAL INFORMATION; FRONT
SUSPENSION AND AXLE..........2-1,2-5,2-16
GENERAL INFORMATION, FRONT WIPERS/
WASHERS...........................8K-8
GENERAL INFORMATION; FUEL SYSTEM....14-1,
14-12,14-16,14-17,14-32,14-62
GENERAL INFORMATION, GAUGE
PACKAGE...........................8E-22
GENERAL INFORMATION; HEATING
AND AIR CONDITIONING................24-1
GENERAL INFORMATION; HORNS..........8G-1
GENERAL INFORMATION; IGNITION
SYSTEMS
.......8D-1,8D-8,8D-20,8D-30,8D-33
GENERAL INFORMATION, INSTRUMENT
CLUSTER; INSTRUMENT PANEL
AND GAUGESÐXJ
....................8E-1
GENERAL INFORMATION, INSTRUMENT
CLUSTER; INSTRUMENT PANEL AND
GAUGESÐYJ
........................8E-14
GENERAL INFORMATION; LUBRICATION
AND MAINTENANCE
....................0-1GENERAL INFORMATION; PROPELLER
SHAFTS.............................16-1
GENERAL INFORMATION; REAR
SUSPENSION AND AXLES........3-1,3-7,3-11
GENERAL INFORMATION; STEERING........19-1
GENERAL INFORMATION; TRANSMISSION
AND TRANSFER CASE.......21-1,21-32,21-66,
21-69,21-156,21-272,21-293
GENERAL INFORMATION; VEHICLE
SPEED CONTROL SYSTEM..............8H-1
GENERAL INFORMATION; WHEELS AND
TIRES..........................22-1,22-6
GENERAL INFORMATION; WIRING
DIAGRAMS..........................8W-1
GENERAL; POWER DOOR LOCKS..........8P-1
GENERAL; POWER MIRRORS.............8T-1
GENERAL; POWER SEATS................8R-1
GENERAL; REAR WINDOW DEFOGGER......8N-1
GENERAL SERVICE INFORMATION; BODY
COMPONENTSÐXJ VEHICLES.........23-132
GENERAL SERVICE INFORMATION;
BRAKES.........................5-20,5-56
GENERAL SERVICE MAINTENANCE..........0-5
GENERAL SERVICE PROCEDURE
INFORMATION.......................19-69
GENERAL SERVICE, STEERING COLUMN . . . 19-45
GENERAL SPECIFICATIONS, 30RH/32RH . . . 21-322
GENERAL SPECIFICATIONS, AW-4........21-324
GENERATOR DIAGNOSTIC TROUBLE
CODE (DTC)........................8A-19
GENERATOR FIELDÐPCM OUTPUT........14-25
GENERATOR LAMPÐPCM OUTPUT........14-25
GENERATOR REPLACEMENTÐLEFT
HAND DRIVE.........................8B-7
GENERATOR REPLACEMENTÐ
RIGHT HAND DRIVE...................8B-9
GENERATOR SERVICE PROCEDURES.......8B-7
GENERATOR SPECIFICATIONS............8B-12
GENERATOR SPLASH SHIELD............13-14
GENERATOR TEST PROCEDURES ON
VEHICLE...........................8A-14
GLASS AND DOOR OPENING WEATHERSTRIP
SEALS, DOOR WINDOW...............23-62
GLASS, FIXEDÐWATER LEAK
DETECTION AND REPAIR........23-83,23-189
GLASS, FIXED WINDOW..........23-73,23-183
GLASS, FRONT DOOR WINDOW..........23-49
GLASS, FULL-METAL DOOR VENT
WINDOW..........................23-177
GLASS, FULL-METAL DOOR WINDOW.....23-178
GLASS, HARD TOP LIFTGATE............23-162
GLASS, HARD TOP QUARTER WINDOW . . . 23-188
GLASS, REAR DOOR FIXED WINDOW......23-53
GLASS, REAR DOOR WINDOW
...........23-52
GLASS REGULATOR, FRONT DOOR
WINDOW
...........................23-48
GLASS REGULATOR, FULL-METAL
DOOR WINDOW
....................23-177
GLASS REGULATOR HANDLE, FULL-
METAL DOOR WINDOW
..............23-175
GLASS REGULATOR, REAR DOOR
WINDOW
...........................23-51
GLASS REPLACEMENT, WINDSHIELD
......23-75
GLASS, SIGHT
........................24-41
GLASS WEATHERSTRIP SEAL
REPLACEMENT, LIFTGATE
.............23-163
GLASS, WINDSHIELD
..................23-185
GLASSÐXJ VEHICLES, LIFTGATE
WINDOW
...........................23-81
GLASSÐXJ VEHICLES, REAR
QUARTER VENT WINDOW
..............23-80
GLASS/REAR QUARTER PLASTIC INSERT
ÐXJ VEHICLES, QUARTER WINDOW
.....23-80
GLOVE BOX
.........................23-194
GOVERNOR AND PARK GEAR
OVERHAUL
........................21-121
GOVERNOR AND PARK GEAR SERVICE
....21-101
GRID REPAIR, REAR WINDOW
DEFOGGER
..........................8N-2
GRID TEST, REAR WINDOW DEFOGGER
.....8N-1
GRILLE AND GRILLE OPENING PANEL
(GOP)
..............................23-3
GRILLE AND SCREEN, COWL
.......23-11,23-139
GRILLE APPLIQUE, RADIATOR
...........23-134
10 INDEXJ
Description Group-Page Description Group-Page Description Group-Page