1994 JAGUAR XJ parking brake

ZF Automatic Transmissions Service Manual
1.3 FAULT DIAGNOSIS
The followina tables are intended as a auide to diaanosis of Dossible faults in the ZF 4 HP 22 transmission. When the
fault involvesa leak, it is recommendedthat it is located by the use of a crack detection fluid, eg Met-L-Check, which
is available in spray form and permits the leak to be located after a short test drive.
1.3.1 Initial Checks
Note: Before attempting diagnosis, ensure that the following settings are checked:
Transmission oil level.
. Ensure that the transmission is at normal operating temperature, eg by conducting a road test. If starting from cold,
. Check that the vehicle is on level ground.
. Firmly apply the parking and footbrakes and run the engine at idle speed.
. To ensure that the system is primed, slowly move the selector lever through all the gear positions.
. With the engine still running, engage ‘P‘ Park, withdraw the dipstick and wipe with a lint free cloth.
. Replace the dipstick slowly and withdraw it noting the level.
. Top up as required and recheck the level.
check
for presence of oil on dipstick at idle
in Park before start of road test.
1.3.2 Engine Tune
Selector cable adjustment.
Check gear selection in all selector positions.
If in doubt, select ’N’, disconnect the cable at the gearbox selector lever, check that the gearbox lever is in ’N’ position
. Adjust as necessary, see Vehicle Service Manual.
(third
detent from the rear) and refit the selector cable ball pin to the lever.
Kickdown switch adjustment, see Vehicle Service Manual.
1.3.3 Stall Test
. Ensure the transmission is at normal running temperature.
. Fully apply the parking brake.
. Fully depress the footbrake.
= Select position ‘D‘- Drive.
. Fully depress the accelerator(’kick-down’ detent fully depressed).
. Note the tachometer reading.
Start
the engine.
. Compare the tachometer reading to the specification.
CAUTION: This test must not last more than 5 seconds. Always allow the engine to idle for at least 2 minutes be- tween tests to allow the transmission fluid to cool down. Do not carry out more than three tests in any
half-hour.
1.3.4 Road Test
Fully check all shift speeds and note. Compare the results with the specification in addition to general observations
of transmission behaviour, noises, leaks etc., and consult the following Fault Finding Chart.
CAUTION: When renewing the transmission, ALWAYS flush out the oil cooler and feed and return pipes.
1.3.5 Electrical Checks
If any electrical component fault issuspected, referto the Electrical Diagnostic Manual (EDM) to verify the failure mode
before a repair or replacement is attempted.
Issue 1 August 1994 33

ZF Automatic Transmissions Service Manual
The torque converter acts in all four forward gears and in reverse. The converter lock-up clutch closes in 4th gear at
a point depending on road speed and accelerator position; engine power is then transmitted
by purely mechanical
means.
A low
-loss oil pump in the front of the transmission housing supplies the converter, the automatic gear shift and the
lubrication circuit; oil is drawn from a sump in the bottom of the gear train housing through a filter. The pump drive
gear is keyed to the converter impeller hub and therefore turns when the engine is running, thereby pressurizing the
oil.
2.1.2 Four-speed Epicyclic Gear Train
The torque converter drives a mechanical epicyclic gear train providing four forward ratios and reverse. Individual ra-
tios are obtained by coupling together the various parts of the gear train by means of solenoid-operated, hydraulically
actuated multi-disc clutches and brakes; built in freewheels permit gear shifts without any interruption of the power
flow.
For information on the operation of the solenoids, clutches, brakes and freewheels, refer to the table below and the
schematic diagrams shown overleaf.
A parking lock pawl is provided at the rear of the gear train, operating on a toothed wheel attached to the output shaft;
the parking lock is operated from the selector (position
'P) by actuator rod.
An electro
-magnetic sensor detects output shaft revolutions by means of a toothed disc attached to the shaft; one rev- olution of the shaft is equal to 36 pulses. The electrical signal from the sensor is passed, via a screened cable, to the
TCM.
R
Park,
Neutral
Solenoid ~
MV2
MVI, MV2
MVI, MV3
MV2
-
MV2
OWC
= one way clutch
Resulting clutch operation
A Clutch drives annulus clockwise
D Clutch OWC holds F carrier against shaft clockwise
E Clutch & OWC drives output shaft clockwise
A Clutch drives annulus clockwise
C1 Clutch holds sungear against anti-clockwise
C Clutch
& OWC holds sungear against anti-clockwise
A Clutch drives annulus clockwise
B Clutch drives sungear clockwise
C Clutch
& OWC holds sungear against anti-clockwise
A Clutch drives annulus clockwise
B Clutch drives sungear clockwise
C Clutch
& OWC holds sungear against anti-clockwise
B Clutch drives sungear clockwise
D Clutch holds carrier against clockwise
E Clutch & OWC drives output shaft anti-clockwise
E Clutch & OWC applied (hydraulics)
40
Issue 1 August 1994

ZF Automatic Transmissions Service Manual
0
2.3 FAULT DIAGNOSIS
The following tables are intended as a guide to diagnosis of possible faults in the ZF 4 HP 24 E transmission. When
the fault involves a leak,
it is recommended that it is located by the use of a crack detection fluid, eg. Met-L-Check,
which is available in spray form and permits the leak to be located after a short test drive.
2.3.1 Initial Checks
&@: Before attempting fault diagnosis, ensure that the following settings are checked:
Transmission oil level
. Ensure that the transmission is at normal operating temperature, e.g. by conducting a 20 mile road test. If starting
. Check that the vehicle is on level ground.
. Firmly apply the parking and footbrakes and run the engine at idle speed.
. To ensure that the system is primed, slowly move the selector lever through all the gear positions.
. With the engine still running, engage 'P' Park, withdraw the dipstick and wipe with a lint free cloth.
. Replace the dipstick slowly and withdraw it noting the level.
. Top up as required and recheck the level.
from
cold: check for presence of
oil on dipstick at idle in 'P' Park before setting off.
Note: The oil level can only be accuratelychecked when at normal temperature-approximately 20 miles at moderate
speeds.
2.3.2 Engine Tune
Selector cable adjustment
. Check gear selection in all selector positions.
. If in doubt, select 'N', disconnect the cable at the gearbox selector lever, checkthat the gearbox lever is in 'N' position
. Adjust as necessary at the selector lever inside the vehicle.
(third detent from the rear) and refit the selector cable ball pin to the lever.
2.3.3 Stall Test
. Ensure the transmission is at normal running temperature.
. Fully apply the parking brake.
. Start the engine.
= Fully depress the footbrake.
. Select position 'D'- Drive.
. Fully depress the accelerator('kick-down' switch fully depressed).
. Note the tachometer reading.
. Compare the tachometer reading to the specification.
CAUTION: This test must not last more than 5 seconds. Always allow the engine to idle for at least 2 minutes between
tests to allow the transmission fluid to cool down. Do not carry out more than three tests in any half-hour.
Jaguar Diagnostic Equipment
(JDE) must be interrogated and any faults identified and rectified (see JDS Manual / In- structions). Check mode switch and gear selector positions using JDE.
60 Issue 1 August 1994

ZF Automatic Transmissions Service Manual
Problem Possible Cause
2.3.4 Road Test
. Fully check all shift speeds and note. Compare the results with the specification in addition to general observations of transmission behaviour, noises, leaks etc., and consult the following Fault Finding Chart.
Action
CAUTION:
When renewing the transmission, ALWAYS flush out the oil cooler and feed and return pipes.
2.3.5 Electrical Checks
. Check 'Kick-down'.
If any electrical component fault is suspected, refer to Electrical Diagnostic Manual (EDM) to verify the failure mode
before a repair or replacement is attempted.
2.3.6 Fault Finding Chart
Stall speed too low
Stall speed too high and keeps
,ising
hceleration below specification
Top speed below specification
'osition 'P - Park
Nil1 not move out of Park
Ioes not engage Park
Ioes not hold Stator
freewheel faulty allowing stator to
revolve
Engine out of tune
Transmission slip
Engine out of tune
Torque converter freewheel faulty
allowing stator to revolve.
'Kick
-down' switch defective.
Transmission
in 'Limp Home' mode
Engine out of tune
Torque converter freewheel seized
Engine out of tune
Gearshift interlock failure
Check cable adjustment
Parking pawl mechanism sticking
Check cable adjustment
Parking pawl mechanism damaged Renew
torque converter
Check engine tune
Check oil level, check mechanical
failure, renew transmission as
necessary
Check engine tune
Renew torque converter.
Refer to EDM, rectify
I renew
'Kick
-down'switch.
Check.
Check
engine tune
Renew torque converter
Check engine tune
Refer to EDM, rectify
- renew fuse,
check circuits, renew relay and
solenoid.
Check central
'P, check Park switch,
check Brake switch.
Adjust to correct setting
Renew park pawl components:
connecting bar, pawl pin, torsion
spring, pawl, guide piece and guide
sheet.
Adjust to correct setting
Replace park pawl components
61 Issue 1 August 1994