1994 HONDA INTEGRA Trouble code

PGM-FI System
rj-t
--t-.
Fuel Supply System
-+-lt@t- -t 13 |- ' "- - --i--
T,-n The Maltunction Indicator Lamp (MlL) indicares Diagnostic Trouble Code (DTC) 43: A problem in
- L:!-i - the Heated Oxygen Sensor (HO2S) circuit. or a probtem in the Fuel Supply System.
NOTE:. Use DIGITAL MULTIMETER.. U6e 2 Volt rang6.
o oooooo oooooo I oo oooooooooooooooooooQoo ooo ooooo I oooo ooooooooooooooo
426
JUMPER WIRE
o ooooo oooo ooo I oo oooooo Isdtcllodsl ooo ooooooooo oooo ooo oo ooo I oooo ooooooooooooooo
D14 {+l
I
426 t-l vohrgo rhould rl.n.t
| 0.4-0.5 V wh.n th..- ignirioo .wilch i! firdt|rtrod o.r, Itd docr!6ato b.low O.1 V in L..th6n two minutaa.
- Tho MIL h.s boen reportod on.- With rhe SCS short con-noctor connocted (soo paga1l-34), codo 43 b indlcat.d,
From codr I troebl.-lhoorlng lprgo 1146).
ls the code 43 accompanied bythe MIL and poor driveability?Go to Fuol Supply .y.t.m (|ecpag6 1t-971.
Do the ECM Reset ftocedure lseepage 11-35).
Connect the SCS short connectorto the service check connector{see page 'l1-34).
Start the engine. Hold the engineat 3,00O rDm with no load {A/T in
@or@ position, M/T in neutral)until the radiator Ian comes on,then let it idle for at least onemanute,
Intonnitl.nt t llure, tydom lr OKat thi. tim. lto.t drlv. mly b.nocaararyr.Chock lor poo? connactlona otloots wiro at C223 lloc.t.d atrlghl lhock towo.]. Cl13lHO2Sland ECM,
Raise the engine speed to 3,000rpm and hold that throttle positiontor at least one minute.Do not vary the throttle positioneven if the rpm drops.
Ooes the MIL blink and does itindicate code 43?
Turn the ignition swilch OFF.
Connect the test harness betweenthe ECM and conneclors {seepage 1 1-371.
With the ignition switch OFF, waitfor at least two minutes.
lnstall a jumper wire on the testharness between A6 and A26.
11-50
1To page 1 1-5'l l

PGM-FI System
Manifold Absolute Pressure (MAP) Sensor
fxai - lfil1 The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 3: An electrical
-:- -?- problem in the Manifold Absolute Pressure (MAPI Sensor circuit.
The MAP sbnsor converts manitold absolute pressure into electrical signals and inputs the ECM.
OUTPUTVOLTAGE
600 700
(in. Hsl GAUGEREADIIIO{mft Hg)
YEL/RED lBlSBl onginc)YEL^YHT lBlaCl .ngin.l | + I
{+l
SENSOR
1.5
- Tho MIL has boon roportod on.- Wirh tho SCS rhort connoctorconnectod lsoo pags 11-34),codo 3 b indicatsd.
Do the ECM Reset Procedure {soepage 11-35).
Intormittont tailuro, lystom ir Ol(at thls timo {tort drivo may bsnocessary).Chack to? Door connocllon oiloosa wiroa 6t C223 {locltod atright shock tow6rl, C'l 14 (MAP
sonaorl and ECM.
ls the MIL on and does it indi-cate code 3?
Turn the ignition switch OFF.
Disconnect the 3P connector tromthe MAP sensor,
Turn the ignition switch ON.
{To page 11-53)
11-52

PGM-FI System
TDC/CKP/CYP Sensor
_f'=l_ fi_l The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 4: A problem int:- the Crankshaft Position (CKP) Sensor circuir.
l'6]- ftl - The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 8: A problem in-i- the ToD Dead Center ITDC) Sensor circuit.
-flG]l- ft-] The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 9: A problem in- , - the Cvlinder Position ICYP) Sensor circuit.
The CKP Sensor determines timing tor fuel injection and ignition of each cylinder and also detects engine speed. TheTDC Sensor determines ignition timing at start-up (cranking) and when crank angle is abnormal. The CYP Sensor detects
the position of No. 1 cylinder tor sequential fudl injection to each cylinder.
- \.--r-l - -__l_-
tPJ:;LlJ:lEl--;l ?,:
- Tho MIL hos beon roponod on.- With rho SCS short connoctorconneclod lsso pago I l-341,code 4, 8 and/or 9 ar6 in-dicated.
Do the ECM Reset procedure (seepage 11-35).
Intohittent failuro, syst€m is OKat thia tima {t6st drivo may benoceaSaayr.Chock for poo. connections orlooss wires at C222 (located atright shock towerl, C110(TOC/CKP/CYP Sonsorl and ECM.
ls the MiL on and does it in-dicate code 4, 8 and/or 9?
Turn the ignition switch OFF.
Disconnect the 8P connector fromthe TDC/CKP/CYP sensor.
{To page 1 1-57)
11-56

PGM-FI System
Engine Coolant Temperature (ECT) Sensor
- ,-!-- ---1- -
t@l- -l 6 | The Malfunction Indicator Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 6: A problem in- - the Engine Coolant Temperature (ECT) Sensor circuit.The ECT Sensor is a temperature dependant resistor (thermistor). The resistance oI the thermistor decreases as th€ en-gine coolant tempe.ature increases as shown below.
J rsG-11
RESISTANCE{k0l
- \.--r-l--t 5 | /--i- \
j 32 68lOrr la0 t76 2t2 2a8 (.Fl-2tt 0 20 rto ao D r@ t20 (,cl
ENGII{E COOLAI{T TCMPERATURE- Th€ MIL has boon roDortod on.- Wlth tho SCS shon connoctorconnoctod {s66 pag6 '11-34},
code 6 is indicatod.
Do the ECM Reset Procedu.e lseepage 1 1-35).
Turn the ignition switch ON.
Intoimittont failur6. ryatom is OKel this lime ltosl d.ive may bonocassaryl.Chock for poor connsctiona orlooso wiros al C223 {locatod attight shock lowor, C111 (ECT
sonsorl, C419 {TCMI and ECM.
ls the MIL on and does it indi-cate code 6?
Start the engine. Hold the engineat 3,O0O rom with no load {Afi in
N or lF]position, M/T in neutral)until the radiator lan comes on,then lot it idle.
Turn the ignition swirch OFF.
Disconnect the 2P conneclor lromthe ECT sensor.
Measure resistance between the2 terminals on the ECT sensor.
ls there 2OO-4OO O?
(To page 1 1-59)
11-58
--

PGM-FI System
Intake Air Temperature (lAT) Sensor
----:-- z ---L /-h6l- I t0 l- The Malfunction Indicator Lamp (MlL) indicstes Diagnostic Trouble Cod6 (DTC) 1O: A problem in/ | / - the Intake Air TemDerature (lAT) Sensor circuit,
The IAT Sensor is a temperature dependant resistor (the.mistor). The resistanc€ of the thermistor d6creases 8s the
intake air temDeratura incroases as shown below.
)1611:till/ ---l- z ---i-\
THERMISTOR
RED/YELI + )
RESTSTAXCE tmt
Bl8Bl onglnc:
-a a2 aa roa .t7a 212 a t |l-20 o 20 rto ao I t6 rro t.cl
I TAKE AIR TEiiIPTFATURE
818C1 .nglnc:IAT SEI{SOR
11-62
wi.a sido
- Th! *llL hs b!!n Egortad on.- \|
rdr dra SCS rhon connrcto.conn.ct.d lt . psg. 1l-341.cod. 10 l. hdlclt.d.
Do the ECM Resot kocoduro {se€pago 11-35).
Turn the ignition switch ON.Into.n{tlont failuro. rys-r.m ir OK .t thi. iim.(toat drlvc m6y b6arooa!!1ryt.Ched( tor poor clnncc-lioiE or loote wlrar 6tC223 lloc.tod rightlhock toworl, C12O(lAT renrcrl and ECM.
ls the MIL on and doos itindicate code 10 ?
Turn the ignition swiich OFF.
Oisconnoct tho 2P connector fromthe IAT sensor.
Meosu.e resistonc€ between the2 torminals on the IAT aengor.
ls thero 0.4-4.0 k0?Rlobco tho IAT aonsor.
(To pago 1'l-63)

PGM-FI System
lgnition Output Signal
i16;11 :ffi1 The Malfunction Indicator Lamp (MlLl indic8tes Diagnostic Trouble Code (DTC) 15: A probl€m in'--=-- . -r- t the lgnition Output Signsl circuir.
I
NOTE| ll the onoine won't stan. itmay take 20 seconds ot cranking to5€t th€ COde.
D|STNIBUTOB
wir6 sido
- Th. MIL hsr b..n roport.d od.- Widr ths SCS .hon cohnecto.connoct€d {..o plgo 11-341,codg |5 i! indicatrd.
Do the ECM Reset ftocedure (seepage 'l'l-351.
Intarmltt nt hllur.. ryltam i. OK!t drlr dm. (t |l drlva mly bonaoaaalry).Chack tor Door cmnactiona orloo|. rYlrar !t C223 llocltld !trlghr .hoct tow.rl, Cl10 (lCMl.nd ECM.
ls th€ MIL on and do€s it indicatecode 15 ?
Turn the ignition swirch OFF.
Turn the ignition switch ON.
Measure voltage betwoon BLK/YEL (+) terminal snd bodygrouno.
R.p.ir op.n In BLK/YEL wlr. bo-ftvarn th. 2P conn.cior lnd ioni-tion rwitch.
ls the.e battory voltage ?
(To page 11-67)
11-66
re*,

PGM-FI System
Vehicle Speed Sensor (VSS)
- _-_f_-., \-=1_ -
It6l- -l tl l- The Maltuncrion Indicator Lamp (MtL)' ths Vehiclo SD6sd (VSS) circuit.
indicateE Diagnostic Trouble Code IDTC) 17: A problem in
a25 {-t
The VSS generates a pulsing signal when the front wheels turn.
@4""rr.r whadr b.lor.
l.d.lnC up tront olcat,
NOTE: Transmission in llj position lA/Tl.
- Tha mll hs b..n ltgortld o.r.* Yvlrh th. Sc]S $o.r coi[cto.connast.d l... ploa I l -341,
cod! 17 i. Indlc.i.d.
Do the ECM Basot Procodur6 16€€pag€ I I -351.
Road rosr whh A/T in13 positaon
{M/T: in 2nd O6ar), accol6rat6 to4,OOO rpm, thon d6c6l6,ate to1,5OO .pm with th.ottlo fullyclosod tor at loast 5 s6conds.
Int rmltllrt t llur., .yrtam b O|(.t drlr drr.Chcct lor poor conicctlon! oalootc wl... !t C3O5 0ocrtad rtLtt rhod. torr.l, eA24. C112IVSA) .nd ECil.
ls th6 MIL on and doos it indic.t6code 'l7 ?
Block roar whe€19 and 5st th6parking brsko. Jsck up th€ f.ontof the c6. and support with saf€-iy standa.
Turn the ignition Bwitch OFF.
Connect tho t€st hamos3 b€tw€€ntho ECM ond connoctora {as€pag6 11-37).
Tu.n th€ ignitioh switch ON.
Block the .ight lront whoel andalowly rctato loft tront wh6ol andm6asur6 voltago b€twoon BlO{+) torminal and A26 l-}terminal.
Doss voltago puleo O V and10 v?Tu.n th€ ignition switch OFF.
Sub|tllul. ! knosn{ood ECMlnd r!ch.ck. lt .Vmgiom/lndlc.-tlon g@.. .w.y, r.pLca di. orlgl-n.l ECM.
ato l+l
0- 10 V ?
11-68
lTo p6ge 1 1-691
llEur

PGM-FI System
Electrical Load Detector (ELDI
tft;-]/ The Maltunction Indicaror Lamp (MlL) indicatss Diagnostic Trouble Code IDTC) 20: A probtem in-Li!- tne Electrical Load Detecror {ELD} circuit.
With lho SCS lhon connectolconnoctod {ree pago 11-34}, cod.20 is indicatod.
Do the ECM B6set Procedurs {seepage 1 'l-35).
Start engine and keep engin€speed at idle.Turn on headlights.
lntennlna tlllure, lyrtom lt Ol(!t irl. dm. (lgtt driv. mly [email protected] for Door connactlona oaloota wiro. rt C218 IELD, lndEctrt.
Ooes the MIL indicato code 20?
Romove the undgr-hood fusg/relay box and remove the tus6/relav box lowet cover.
Turn lhe ignition switch ON.
Measure voltage betw€on BLK/YEL (+l terminal and BLK (-)terminal.
Msasuro voltag€ b€tweon BLK/Y€L {+) terminal snd bodvground.ls there bartory voltagel
Rcpir oo.n in BLK wir.batwaan lha 3P connrc-tor lnd G2Ol {loc.t.dtroit ot angh|. comprn-m.r dghl .ld.l,
B.p.lr op.n in BLKrYEL wlrr b.-tw..n o.24ACG (ALn flcl115A: Bl88l .ngln!, 20 A:818C1cnginol fu!. In thr und.r{..htu.o/r.lly bor lnd tho 3P con-rcclo?.
View tromwire side
BLK (-)
(To page 11-7'l)
GRn/iED I - |
BLK/YEL I + I
11-70