1994 GMC SIERRA engine coolant

I NOTICE:
If you use an improper coolant mix, your engine could overheat
and be badly damaged.
The repair cost wouldn’t be covered by
your warranty.
Too much water in the mix can freeze and crack
the engine, radiator, heater core and other parts.
Some conditions, such as air trapped in the cooling system, can affect the
coolant level
in the radiator. Check the coolant level when the engine is cold
and follow the steps under “Adding Coolant” for the proper way to add
coolant.
If you have to add coolant more than four times a year, have your dealer
check your cooling system.
If you use the proper coolant, you don’t have to add extra
inhibitors or additives which claim to improve the system. These
can be harmful.
Adding Coolant -Gas Engines
To Check Coolant
The coolant recovery
tank
is located on the
passenger side at the
rear corner
of the
engine compartment.
When your engine
is cold, the coolant level should be at COLD, or a little
higher. When
your engine is warm, the level should be up to HOT, or a little
higher.
6-39
ProCarManuals.com

To Add Coolant
If you need more coolant, add the proper mix at the coolant recovery tunk.
A CAUTION:
Turning the radiator pressure cap when the engine and radiator
are hot can allow steam and scalding liquids to blow out and
burn you badly. With the coolant recovery tank, you will almost
never have to add coolant at the radiator. Never turn the
radiator pressure cap
- even a little - when the engine and
radiator are hot.
Add coolant mix at the recovery tank, but be careful not to spill it.
A CAUTION:
You can be burned if you spill coolant on hot engine parts.
Coolant contains ethylene glycol, and it will burn
if the engine
parts are hot enough. Don’t spill coolant on a hot engine.
Adding Coolant -Diesel Engines
The coolant surge tank
is located on the
passenger side at the
rear corner
of the
engine compartment.
6-40
ProCarManuals.com

To Check Coolant
When your engine is cold, the coolant level should be at the COLD mark,
or a little higher. When your engine is warm, the level should be above the
COLD mark.
If this light comes on,
it means you’re low
on engine coolant.
To Add Coolant
If you need more coolant, add the proper mix at the surge tnnk, but only
when the engine is cool.
Open the air bleed valve on the thermostat housing to allow trapped air
out
of the system. Close the bleed valve when coolant begins to flow out.
I A CAUTION:
nrning the surge tank pressure cap when the engine and
radiator are hot can allow steam and scalding liquids to blow
out:
and burn you badly. Never turn the surge tank pressure cap -
even a little - when the engine and radiator are hot.
A CAUTION:
You can be burned if you spill coolant on hot engine parts.
Coolant contains ethylene glycol, and it will burn if the engine
parts are hot enough. Don’t spill coolant on
a hot engine.
6-41
ProCarManuals.com

Radiator Pressure Cap-Gas Engines
The radiator pressure
cap must be tightly
installed with the
arrows
on the cap
lined
up with the
overflow tube
on the
radiator filler neck.
NOTICE:
Your radiator cap is a 15 psi (105 kPa) pressure-type cap and
must be tightly installed to prevent coolant
loss and possible
engine damage from overheating. Be sure the arrows
on the cap
line
up with the overflow tube on the radiator filler neck.
Surge Tank Pressure Cap- Diesel Engines
6-42
ProCarManuals.com

NOTICE:
Your surge tank pressure cap is a unique 15 psi (105 kPa)
pressure-type cap for use with surge tank cooling systems only.
It must be tightly installed to prevent coolant
loss and possible
engine damage from overheating. Be sure the arrows on the cap
line up with the top tube
of the coolant surge tank.
Thermostat
Engine coolant temperature is controlled by a thermostat in the engine
coolant system. The thermostat stops
the flow of coolant through the
radiator
until the coolant reaches a preset temperature.
When
you replace your thermostat, an AC" thermostat is recommended.
Power Steering Fluid
NOTICE:
Always turn the engine off before checking or adding power
steering fluid. The power steering pump cap is close to the fan
and other moving parts.
How To Check Power Steering Fluid
Unscrew the cap and
wipe the dipstick
with
a clean rag. Replace
the cap and completely
tighten it. Then
remove the cap again
and
look at the fluid
level on the dipstick.
6-43
ProCarManuals.com

Heater or A/C Control Lamp
Four Wheel Drive Indicator
rour Wheel Drive Shift Lever
Instrument Panel Compartment Lamp
Ashtray Lamp
Sunshade Vanity Mirror
"Crew Cab Only
LAMP OR BULB
INSTRUMENT PANEL
Transmission Indicator (PRNDL)
Daytime Running Lights Indicatory
Charging System Indicator Lamp
Instrument Cluster Illumination
--Gage Cluster
Instrument Cluster Illumination
-Tachometer Cluster
Headlamp Beam Indicator
Directional Signal Indicator
Brake Warning Indicator
Safety Belt Warning
Check Gages Indicator
Malfunction Indicator ("Service
Engine Soon") Lamp
Upshift Indicator
Glow Plugs Lamp*:$:
Low Coolant
Water
in Fuel Lamp*'$
Service Throttle Soon Lamp*"
194
161
194
194
I94 74
TRADE NO.
161
74
74
I94
I94 74 74
74
74 74
74
74
74
74
74
74
6
6-98
ProCarManuals.com

Explanation Of Scheduled Mainienance Services
Below are explanations of the services listed in the maintenance charts.
The proper fluids and lubricants to use are listed in this section. Make sure
whoever services your vehicle uses these. All parts should be replaced and
all necessary repairs done before you or anyone else drives the vehicle.
1. ENGINE OIL AND OIL FILTER CHANGE“‘ - ALWAYS USE
SJ3 ENERGY CONSERVING I1 (GASOLINE ENGINE) OR CF-4/SH
(DIESEL ENGINE) QUALITY OILS
OF THE PROPER VISCOSITY.
To determine the preferred viscosity oil for your vehicle’s engine (e.g.
SAE 5W-30 or 10W-30), see “Engine Oil”
in the Index.
2. CHASSIS LUBRICATION - Lubricate the front suspension, king
pin bushings, steering linkage, transmission, and transfer case shift
linkage, parking brake cable guides, rear driveline center splines and
front axle propshaft splines, brake pedal springs, and clutch pedal
springs at the intervals specified.
If you have a 3500
HD, lubricate the king pins and king pin bushings,
every
1,500 miles (2500 km) for Maintenance Schedule I, or every
3,000 (5000 km) for Maintenance Schedule 11.
Ball joints and king pin bushings should not be lubricated unless their
temperature
is 10” F (-12”C), or higher. When the weather is cold, let
them warm up before lubrication or
they could be damaged.
Also, be sure
to check all the vehicle fluid levels at this time.
3.
CLUTCH FORK BALL STUD LUBRICATION (5-SPEED
MANUAL TRANSMISSION WITH DEEP LOW
) - Lubricate the
clutch fork ball stud through the fitting
on the clutch housing.
Lubricant must be added “sparingly” to
the fitting, as only .0066 lb.
(.003 kg) is required to lubricate the ball stud surface. Do not add
lubricant more often than the intervals
in the Maintenance Charts. Too
much lubricant will damage the clutch assembly.
4. COOLING SYSTEM SERVICE”’? - Drain, flush and refill system
with new coolant. See “Engine Coolant” in the Index for
the proper
coolant and mixture to use
in your vehicle.
Also inspect the hoses and replace them
if they are cracked, swollen, or
deteriorated. Tighten all hose clamps (except constant tension clamps).
Remove debris and clean the outside of the radiator and air
conditioning condenser. Wash the radiator neck.
To ensure proper
operation, pressure test.
the radiator and cap.
* An Emission Control Service
?A fluid
loss in these systems may indicate a problem. Have them
inspected and repaired at once.
7-18
ProCarManuals.com

Recommended Fluids & Lubricants
NOTE: Fluids and lubricants identified below by name, part number or
specification may be obtained from your GM Dealer.
USAGE
Engine Oil - Gasoline
Engines
Engine
Oil - Diesel Engines
Engine Coolant
Hydraulic Clutch System
Hydraulic Brake Systems
Parking Brake Cables
Power Steering System
Automatic Transmission
FLUIDLUBRICANT
API service SH or SG Energy
Conserving I1 oils
of the recommended
viscosity. The
“SH” designation may be
shown alone or
in combination with
others, such
as “SH/CD,” “SH, SG,
CD,”“SG/CD,” etc. To determine the
preferred viscosity for your vehicle’s
engine, see “Engine Oil” in the Index.
API service CF4SH. The
“CF4SH”
designation may be shown alone or in
combination
with others, such as
“CF-4/SG,” “CE/SH” or “CE/SG,” etc.
The designation may
also be listed in
reverse order, such
as “SH/CF-4.” To
determine the preferred viscosity for
your vehicle’s engine, see “Engine Oil”
in the Index.
Mixture
of water and a good quality
ethylene glycol base antifreeze
conforming
to “GM Specification
6038-M” (GM Part No. 1052753)’ or
approved recycled coolant conforming to
“GM Specification
603%”’ with a
complete coolant flush and refill.
Hydraulic Clutch Fluid (GM Part No.
I2345347 or equivalent).
Delco Supreme
11 @ brake fluid (GM
Part No.
1052535 or equivalent DOT-3
brake fluid).
Chassis Lubricant (GM Part No.
I2346003 or equivalent) or lubricant
meeting requirements of NLGI Grade
2,
Category LB or GC-LB.
GM Power Steering Fluid (GM Part
No. 1050017 or equivalent) conforming
to
“GM Specification 99850 10.”
DEXRON~ 111 or DEXRON~ IIE
Automatic Transmission Fluid.
7-26
ProCarManuals.com