1994 CHEVROLET TRACKER stop start

Comfort Controls and Audio Systems
Tone Select: Press “TONE SELECT” to
choose preset treble and bass equalization
settings designed for “ROCK,” “NEWS,”
“POP,” “JAZZ” and “CLASSICAL.”
“ROCK” will appear when you first press
“TONE SELECT.” Each time you press
it, another setting will appear
on the
display. Press
it after “CLASSICAL” and
tone control will be back to the treble and
bass knobs.
Adjusting the Speakers
Fade:
Turn the “FADE” knob to move the
sound between the front and rear
speakers.
Balance: Turn the “BAL” control behind
the “FADE’ knob to move the sound
between the right and left speakers.
Recall
Press “RCLVA” to see the station being
played for a moment. Or, press it if you
want to see the time when the ignition is
off.
To Play a Cassette Tape
Your tape player is built to work best with
tapes that are
30 to 45 minutes long on
:ach side. Tapes longer than that are so
:hin they may not work well in this player.
The longer side with the tape visible
;hould face to the right. If you hear
lothing or hear just a garbled sound, it
nay not be in squarely. Press “STOP’ or
‘EJECT” to remove the tape and start
mer.
Once the tape is playing, use
the knobs
For volume, fade and balance, just as you
io for radio. The lighted arrows show
which side of the tape is playing.
Metal Tapes: Your bias is set
automatically. When a metal or chrome
tape is inserted, “MTL” will appear on the
display.
Fast Forward: Press “FF” to advance
rapidly to another part of the tape. Press
“FF,” “RCLVA” or “STOP’ to return to
playing speed.
Rewind: Press “REW’ to reverse the tape
rapidly. Press “REW,” “RCL~A” or
“STOP’ to return to playing speed.
Next Selection: Press “NXT” to go
forward to the beginning of the next
selection. Press “NXT” again or press
“RCL
vA’’ or “STOP” to cancel this
function.
Previous Selection: Press “PRV” to go
lack to the beginning
of the selection.
?rem “PRV” again or press “RCL
VA” or
‘STOP’ to cancel this function.
Por “NXT” and “PRV” to work properly,
your tape must have at least three or four
seconds of silence between each
selection.
Repeat: Press “RPT” to go to the
beginning of the selection and play
it
3gain. Press “RPT” again to cancel this
Function.
Noise Reduction: Press 00 to remove
noise from Dolby@
B NR-encoded tapes.
Dolby@
B Noise Reduction manufactured
under license from Dolby Laboratories
Licensing Corporation.
“Dolbya7’ and the
00 symbol are
trademarks of Dolby Laboratories
Licensing Corporation.
Radio Monitor: When playing a tape,
press “RDM” during
“FF” or“REW’ to
hear
the radio. Press “RDM’ again to turn
the radio off. During “RDM’ operation,
only “TUNE,” “SEEK’ and “PSCAN’
will work.
Tape Sides: Press “RCL VA” to switch
from one side of the tape to the other.
... 94
ProCarManuals.com

Stop: Press “STOP” to stop the tape and
switch to radio.
Eject: Press “EJECT” to remove the tape
and switch
to radio.
To Play a Compact Disc
Don’t use the mini-discs (3” singles).
They won’t eject. Use full-size compact
discs.
Insert your disc into the CD slot on your
audio system.
If the disc comes back out, it could be
that:
0 The disc is upside down.
0 It is dirty, scratched, or wet.
There is too much moisture in the air.
(If there is, wait about one hour and
try again.)
If you see “Err” on the display, the disc
player is too
hot to play the disc. Press
“RCL
VA’’ to take “Err” off the display.
Track Number and Playing Time: Press
“RCL
VA” to see which track is playing.
Press it again
within five seconds to see
how long it has been playing. The
track number also appears when the
disc is inserted or you change the volume.
Previous Track: Press “PRV” to hear a
track again.
If you hold this button, or
press it more than once, the disc will
return to previous tracks.
Next Track: Press ”NXT” to hear the
next track now (instead
of waiting until
the present track is finished).
If you hold this button, or press it more
than once, the disc will advance further.
Rewind: Press and hold “REW” to return
rapidly to a favorite passage. Release
it to
play the passage.
Fast Forward: Press and hold “FF” to
advance quickly
within a track. Release it
to resume playing.
Compression: Press “COMP’ to make
soft and loud passages more nearly equal
in volume.
Repeat: Press “RPT” once to hear a
selection over again.
Rasdom: Pressing “RDM” will cause the
CD player to play the tracks back in
random order. To cancel the random
feature, press
“RDM,” “STOP” or “RPT.”
Stop: Press “STOP” to stop playing the
disc and switch to radio. Press “STOP”
again
to restart the disc at the point where
it stopped. Press “AM-FM” to cancel CD
operation and listen to the radio.
CD-Tape: Press “CD-TP” to switch
between playing a tape
and a CD when
both are inserted.
Eject: Press “EJECT” to eject the disc
and the radio will play. The disc
will start
playing at track
1 when you reinsert it.
Special Eject
If you choose, you can eject only the tape
or CD when you have both a CD and a
tape
in your audio system.
CD Only: To eject only the CD, press
“EJECT” and then press “REW.”
Tape Only: To eject only the tape,
press “EJECT” and then press
“PRV.”
95 ...
ProCarManuals.com

Your Driving and the Road
Passing
The driver of a vehicle about to pass
another on a two-lane highway waits for
just
the right moment, accelerates, moves
around the vehicle ahead, then goes back
into the right lane again.
A simple
maneuver?
Not necessarily! Passing another vehicle
on a two-lane highway is
a potentially
dangerous move, since the passing
vehicle occupies the same lane as
oncoming traffic for several seconds.
A
miscalculation, an error in judgment, or a
brief surrender to frustration or anger can
suddenly put the passing driver face to
face with the worst of
all traffic accidents
- the head-on collision.
So here are some tips for passing:
“Drive ahead.’’ Look down the road,
to the sides, and to crossroads for
situations that might affect your
passing patterns. If you have any
doubt whatsoever about making a
successful pass, wait for a better time.
Watch for traffic signs, pavement
markings, and lines.
If you can see a
sign up ahead that might indicate
a
turn or an intersection, delay your
pass. A broken center line usually
0
0
indicates it’s all right to pass
(providing the road ahead is clear).
Never cross
a solid line on your side
of the lane or a double solid line, even
if the road seems empty of
approaching traffic.
Do not get too close to the vehicle you
want
to pass while you’re awaiting an
opportunity. For one thing, following
too closely reduces your area of
vision, especially
if you’re following a
larger vehicle.
Also, you won‘t have
adequate space if the vehicle ahead
suddenly slows or stops. Keep back a
reasonable distance.
When
it looks like a chance to pass is
coming up, start to accelerate but stay
in the right lane and don’t get too
close. Time your move so you will be
increasing speed
as the time comes to
move into the other lane. If the way is
clear
to pass, you will have a “running
start” that more than makes up for the
distance you would lose
by dropping
back. And if something happens to
cause you
to cancel your pass, you
need only slow down and drop back
again and wait for another
opportunity.
0
0
0
0
0
If other cars are lined up to pass a
slow vehicle, wait your turn.
But take
care that someone isn’t trying to pass
you as you pull out to pass the
slow
vehicle. Remember to glance over your
shoulder and check the blind spot.
Check your mirrors, glance over your
shoulder, and start your left lane
change signal before moving out
of
the right lane to pass. When you are
far enough ahead of the passed vehicle
to see its front
in your inside mirror,
activate your right lane change signal
and move back into the right lane.
(Remember that your right outside
mirror is convex. The vehicle you just
passed may seem
to be farther away
from you than
it really is.)
Try not to pass more than one vehicle
at a time on two-lane roads. Reconsider
before passing the next vehicle.
Don’t overtake a slowly moving
vehicle
too rapidly. Even though the
brake lights are not flashing,
it may
be slowing down or starting to
turn.
If you’re being passed, make it easy
for the following driver to get ahead
of you. Perhaps you can ease
a little
to the right.
. . .lo6
ProCarManuals.com

loss of Control
Let's review what driving experts say
about
what happens when the three
control system (brakes, steering and
acceleration) don't have enough friction
where
the tires meet the road to do what
the driver has asked.
In any emergency. don't give up. Keep
trying
to steer and constantly seek an
escape route or area
of less danger.
Skidding
In a skid. a driver can lose control of the
vehicle. Defensive drivers avoid most
skids by taking reasonable care suited
to
existing conditions. and by not
"overdriving" those conditions. But skids
are always possible.
The three types
of skids correspond to
your Geo's three control systems. In the
braking skid your wheels are.n't rolling.
In
the steering or cornering skid, too much
speed or steering
in a curve causes tires to
slip and lose cornering force. And
in the
acceleration skid too much throttle causes
the driving wheels
to spin.
A cornering skid and an acceleration skid
are best handled by easing your foot off
the accelerator pedal.
If your vehicle starts to slide, ease your
foot 011' the accelerator pedal and quickly
steer the way
you want the vehicle to go.
If you start steering quickly enough. your
vehicle
may straighten out. 41ways be
ready for
;I sccond skid if it occurs.
Of course, traction is reduced when water,
snow. ice. gravel. or other material is on
the road. For safety, you'll want to slow
down and adjust your driving
to these
conditions.
It is important to slow down
on slippery surfaces because stopping
distance will be longer
and vehicle
control more limited.
While driving on
a surface with reduced
traction.
try your best to avoid sudden
steering, acceleration,
or braking
(including engine braking by shifting
EO a
lower gear).
Any sudden changes could
cause the tires to slide. You may
not
realize the surface is slippery until yout-
vehicle is skidding. Learn
to recognize
warning clues
~ such as enough water,
ice or packed snow
on the road to make ;1
"nlir~-or.ed surf'rlce" - and slow down
when you have any doubt.
Remember: The rex-wheel anti-lock
braking system (RWAL) helps avoid
only
a rear braking skid. In a braking skid
(where the front wheels are
no longer rolling),
release enough pressure
on the
brakes to get the front wheels rolling
again. This restores steering control. Push
the brake pedal down steadily when you
have
to stop suddenly. As long as the
I'ront wheels are rolling,
you will have
sleering control.
Driving Guidelines
This multipurpose passenger vehicle is
defined as a utility vehicle in Consumer
Information Regulations issued
by the
National I-lighway Traffic Safety
Administration (NHTSA)
of the United
States Department of Transportation.
Utility vehicles have higher ground
clearance and a narrower track to make
them capable of performing
in a wide
variety
of off-road applications. Specific
design characteristics give them a higher
center of gravity than ordinary cars. An
advantage
of the higher ground clearance
is
a better view of the road allowing you
to anticipate problems. They are not
designed for cornering
at the same speeds
as conventional 2-wheel drive vehicles
any no re than low-slunl 7 .'p '-, orts cars are
designed
to perform satisfitctorily under
off-road conditions.
If at all possible,
avoid shurp turns or abrupt maneuvers.
107 ...
ProCarManuals.com

0 Is the hill simply too rough‘? Steep hills
often have ruts, gullies, troughs and
exposed rocks because
they are more
susceptible
to the effects of erosion.
Driving Uphill
Once you decide you can safely drive up
the hill,
you need to take some special
steps.
0 Use a low gear and get a firm grip on
the steering wheel.
Get a smooth start up the hill and try
to maintain your speed. Don’t use
more power than
you need, because
you don’t want your wheels
to start
spinning or sliding.
Try to drive straight up the hill if at a1
possible.
If the path twists and turns,
you might want to find another route.
0
0
0
0
Ease up on your speed as you
approach the top
of the hill.
Attach a flag to the vehicle to tnake
you more visible to approaching
traffic on trails
or hills.
Sound the
horn as you approach the
top
of the hill to let opposing traffic
know you’re there.
Use your headlights even during the
day. They make you more visible
to
oncoming traffic.
Q: What should I do if my vehicle
A:
0
0
0
0
stalls, or is about to stall, and I can’t
make
it up the hill?
If this happens, there are some things
you should do, and there are some
things you must not do. First, here’s
what you should do:
Push the brake pedal
to stop the
vehicle and keep
it from rolling
backwards. Also, apply
the parking
brake.
If your engine is still running, shift the
transmission into reverse, release the
parking brake, and slowly back down
the
hill in reverse.
If your engine has stopped running,
you’ll need to restart it. With the brake
pedal depressed and
the parking brake
still applied,
shift the transmission to
“P” (Park) (or, shift to “N” (Neutral)
if your vehicle has a manual
transmission) and restart
the engine.
Then, shift
to reverse, release the
parking brake, and slowly back down
the
hill as straight as possible in
reverse.
As you are backing down the hill, put
your left hand
on the steering wheel at
the
12 o’clock position. This way,
111 . . .
ProCarManuals.com

0 Are there hidden surface obstacles?
Ruts? Logs? Boulders?
0 What’s at the bottom of the hill? Is
there a hidden creek bank or even a
river bottom with large rocks?
If you decide you can go down a
hill
safely, then try to keep your vehicle
headed straight down, and use a low gear.
This way, engine drag can help your
brakes and they won’t have to do all the
work. Descend slowly, keeping your
vehicle under control at all times.
Q: Are there some things I should not
do when driving down
a hill?
A: Yes! These are important because if
you ignore them you could lose
control and have a serious accident.
When driving downhill, avoid turns
that take you across the incline
of the
hill.
A hill that’s not too steep to drive
down may be too steep to drive
across. You could roll over if you
don’t drive straight down.
Never go downhill with the
transmission in “N” (Neutral), or with
the clutch pedal depressed in a manual
shift. This is called “free-wheeling.”
Your brakes will have to do all the
work and could overheat and fade.
Avoid braking
so hard that you lock
the front wheels when going downhill.
If your front wheels are locked, you
can’t steer your vehicle. If your
wheels lock up during downhill
braking, you may feel the vehicle
starting to slide sideways.
To regain
your direction, just ease
off the brakes
and steer to keep the front of the
vehicle pointing straight downhill.
Q: Am I likely to stall when going
downhill?
A:
0
0
0
0
It‘s much more likely to happen going
uphill.
But if it happens going
downhill, here’s what to do.
Stop your vehicle by applying the
regular brakes. Apply the parking
brake.
Shift to
“P” (Park) (or to Neutral with
the manual transmission) and, while
still braking, restart the engine.
Shift back to a low gear, release the
parking brake, and drive straight down.
If the engine won’t start, get out and
get help.
Driving Across an Incline
Sooner or later, an off-road trail will
probably go across the incline
of a hill. If
this happeris, you have to decide whether
to try to drive across the incline. Here are
some things to consider:
0 A hill that can be driven straight up
or down may be too steep to drive
across. When you go straight up or
down a hill, the length
of the wheel
base (the distance from the front
wheels to the rear wheels) reduces the
113 :. .
ProCarManuals.com

Your Driving and the Road
long as your tailpipe is under water, you'll
never be able to
start your engine. When
you go through water, remember that
when your brakes get wet, it may take
you longer to stop.
After Off-Road Driving
Remove any brush or debris that has
collected
on the underbody, chassis or
under the hood. These accumulations can
be a fire hazard.
After operation in mud or sand, have the
brake linings cleaned and checked. These
substances can cause glazing and uneven
braking. Check the body structure,
steering, suspension, wheels, tires, and exhaust system
for damage.
Also, check
the fuel lines and cooling system for any
leakage.
Your vehicle will require more frequent
service due to off-road
use. Refer to the
Maintenance Schedule for additional
information.
4 Driving at Night
Night driving is more dangerous than day
driving. One reason is that some drivers
are likely
to be impaired - by alcohol or
drugs, with night vision problems, or by
fatigue.
Here are some tips on night driving.
Drive defensively.
Don't drink and drive.
Adjust your inside rearview mirror to
reduce the glare from headlights
behind you.
Since you can't see as well,
you may
need to slow down and keep more space between
you and other vehicles.
. . .116
ProCarManuals.com

Slow down, especially on higher
speed roads. Your headlights can light
up
only so much road ahead.
0 In remote areas. watch for animals.
0 If you're tired, pull off the road in a
safe place md rest.
Night Vision
No one can see 11s well at night as in the
daytime.
But as we get older these
differences increase. A SO-year-old driver
may require at least twice as much
light to
see the same thing
a( night :is a
20-year-old.
What you do
in the daytime can also
affect your night vision. For example.
if
you spend the day in bright sunshine you
are wise
to wear sunglasses. Your eyes
will have less trouble adjusting
to night.
But
if you're driving, don't wear
sunglasses at night. They may cut down
on glare from headlights. but they also
make
a lot of things invisible.
You can be temporarily blinded by
approaching lights. It c;tn take a second or
two,
or even several seconds, for your
eyes
to readjust to the dark. When you are
ked with severe glare
(as from a driver
who doesn't lower the high beams. or a vehicle with Inisaimed headlights), slow.
down
a little. Avoid staring directly into
the approaching lights.
Keep your windshield and
all the glass on
your vehicle clean - inside and out.
Glare
at night is nladc much worse by dirt
on the glass. Even the inside of the glass
can build up a film caused by dust. Dirty
glass makes lights dazzle and flash more
than clean
glass would. making the pupils
of
your eyes contract repeatedly.
Remember that your hcacilights light
up
far less of' LI roadway when you are in a
turn or curve.
Kecp your eycs moving: that way,
it's
casier to pick out dimly lighted objects.
Just
as your headlights should be checked
regularly for proper aim.
so should your
eyes be examined regulurly.
Some drivers
suffer from night blindness
- the
inability to see
in dim light - and aren't
even aware
of it.
Driving in the Rain
Rain and wet roads can mean driving
trouble. On
a wet road you can't stop,
accelerate
or turn as well because your
tire-to-road traction isn't as good as on
dry roads. And,
if your tires don't have
much tread left, you'll get even less
traction.
It's always wise to go slower and
be cautious if
rain starts to fall while you
are driving. The surface may get wet
suddenly when your reflexes are tuned for
driving
on dry pavement.
The heavier the rain. the harder
it is to
see. Even if your windshield wiper blades
are
in good shape. a heavy rain can make
it harder to see road signs and traffic
signals, pavement markings,
the edge of
the road, and even people walking.
117 ...
ProCarManuals.com