1994 CHEVROLET ASTRO PASSENGER start stop button

Downloaded from www.Manualslib.com manuals search engine Clock
To set the clock, just:
Push SET.
Within 5 seconds, push ant Ild SCA .N until the correct hour appears.
0 Press and hold SEEK until the correct minute appears.
To display the clock
with the ignition off, push the upper knob. The time
will be displayed for a few seconds.
Cassette Tape Player
Your tape player is built to work best with tapes that are 30 to 45 minutes
long on each side. Tapes longel [an that are
so thin they may not work well
in this player.
To play a cassette tape:
Have the radio on.
0 Insert the tape squarely rnrough the tape door.
The longer side with the tape visible goes in first. If you hear nothing or
hear just garbled sound, it may not be
in squarely. Push STOP-E JECT to
remove the tape and start over.
Once the tape is playing, use the upper and lower knobs for volume and
balance, just
as you do for radio. The arrows show which side of the tape is
playing.
To go forward to another part of the tape, push the button with an
arrow pointing toward the lighted arrow.
To stop the tape, push the
STOP-E JECT button lightly.
To go backward, push the button with an arrow pointing away from
the lighted arrow. To stop the tape, push the
STOP-EJECT button
lightly.
To go from one side of the tape to the other, push in the upper knob on
your radio.
To remove or stop the tape, push STOP-EJECT.
3-15

Downloaded from www.Manualslib.com manuals search engine Clock
To set the clock, just:
0 Press SET. (SET appears in the VF display for a few seconds.)
Within 5 seconds, push and hold SCAN until the correct hour appears.
0 Press and hold SEEK until the correct minute appears.
To display
the clock with the ignition off, push the upper knob. The time
will be displayed for a few seconds.
To Play A Cassette
Your tape player is built to work best with tapes that are 30 to 45 minutes
long on each side. Tapes longer than that are
so thin they may not work well
in this player.
To play a cassette tape:
Have the radio on.
0 Insert the tape squarely through the tape door.
The longer side with the tape visible goes in first. If you hear nothing or
hear just garbled sound, it may not be
in squarely.
Push
STOP-EJECT to remove the tape and start over.
Once the tape is playing, use the upper and lower knobs for volume and
balance, just as you do for radio. The arrows show which side of the tape is
playing.
0 To go forward to another part of the tape, push ,.
To go backward, push 4. To stop the tape, push the STOP-E JECT
button lightly.
0 To go from one side of the tape to the other, push in the upper knob on
your radio. To remove or stop the tape, push
STOP-EJECT.
APS (Automatic Program Search)
Press this button to activate the automatic program search. When the
button is pressed, the tape will rapidly advance to the beginning
of the next
selection. When the
4 button is pressed, the tape will rapidly reverse to the
beginning
of the current selection.
Press
STOP-EJECT to remove the cassette and start the radio.
3-18

Downloaded from www.Manualslib.com manuals search engine To Play A Compact Disc (CD)
NOTICE:
Before you begin, please note: DO NOT use mini-discs that are
called singles, They won’t eject. USE FULL-SIZE COMPACT
DISCS.
If the disc player is very hot, or if you’re driving on a very rough
road,
a disc may come out or just not play. If you see the word
HOT
on the display, the disc player is too hot to play the disc.
Press RCL to make the word HOT
go off the display. When
things get back
to normal, the disc should play again. Press
PWR to turn the system
on,
Insert a disc partway into the slot, label side up. The player will pull it in.
Wait a few seconds and the disc should play.
If the disc comes back out, check whether:
0 The disc is upside down.
0 It is dirty, scratched, or wet.
Too much moisture is in the air. (If there is, wait about one hour and try
again.)
RCL
Press RCL to see what track is playing. Press it again within
5 seconds to
see how long it has been playing. The track number also appears when
you
change the volume or when a new track starts to play.
COMP
Press the COMP button
to make soft and loud passages more nearly equal
in volume. COMP appears in the display while using this command.
RDM
The RDM button means random and when
it is pressed, it causes the CD
mechanism to play the tracks in a random order rather than in the sequenti\
al
1,2,3 order.
REV
Press and hold the REV button to quickly return to a favorite passage. The
counter reading will be displayed when using this control.
FWD
Press and hold the FWD button to advance quickly within
a track. Release it
to resume playing. Watch the display to stop at a specific passage.

Downloaded from www.Manualslib.com manuals search engine SCAN
Press SCAN to sample each track for approximately 10 seconds. Scanning
will continue until the
RDM, SCAN or any other motion button is pressed
again.
PREV
If you hold the PREV (4 SEEK ) button, or press it more than once, the
disc will return to previous tracks.
NEXT
Press NEXT (SEEK b ) to hear the next track now instead of waiting until
the present track
is finished. If you hold this button or press it more than
once, the disc will advance further.
ST-PL
Press ST-PL (Stop-Play) to make the disc stop and the radio play. Press
ST-PL again to restart the disc at the point where it stopped.
Press
PWR or turn the ignition key off to stop the disc player. The disc
stays in the player and will resume playing at the point where
it stopped.
Press
EJCT to eject the disc and make the radio play. The disc will start at
track
1 when you reinsert it.
Anti-Theft Feature
Delco LOC II@ is an Anti-Theft feature for the compact disc player. It can
be used or ignored.
If ignored, the system plays normally. If it is used, your
player won’t be usable if
it is ever stolen, because it won’t turn on.
The instructions below tell you how
to enter a secret code into the system. If
your car loses battery power for any reason, you must unlock the system
with the secret code before
the radio will turn on.
To Lock The System:
1. Write down any 6 digit number and keep it in a safe place.
2. Turn the ignition to the ACC (Accessory) or RUN position.
3. Press the PWR button to turn the radio off.
4. Press the 1 and 4 buttons together. Hold them down until “- - -” shows
on the display.
You are now ready to enter your secret code. Don’t wait more than
15 seconds between steps.
5. Press SET and 000 will appear on the display.
6. Press the SEEK b or 4 button to make the first number appear.
7. Press SCAN to make the last two numbers agree with your code.
3-23