1994 CADILLAC DEVILLE oil type

Downloaded from www.Manualslib.com manuals search engine Care of Your Cassette Tape Player
A tape player that is not cleaned regularly can cause reduced sound
quality, ruined cassettes, or a damaged mechanism. Cassette tapes should
be stored in their cases away from contaminants, direct sunlight, and
extreme heat. If they aren't, they may not operate properly or cause
failure
of the tape player.
Your tape player should be cleaned after every
50 hours of use. If you
notice
a reduction in sound quality, try a known good cassette to see if the
tape
or the tape player is at fault. If this other cassette has no
improvement
in sound quality, clean the tape player.
Cleaning may be done with a scrubbing action, non-abrasive cleaning
cassette. This system uses a cleaning cassette with pads which scrub the
tape head as the hubs of the cleaner cassette turn. It is normal for the
cartridge to eject while cleaning. Insert the cassette at least
3 times to
ensure thorough cleaning.
A scrubbing action cleaning cassette is
available through your Cadillac dealership.
You may also choose a non-scrubbing action, wet-type cleaner which uses
a cassette with a fabric belt to clean the tape head. This type
of cleaning
cassette will
not eject. It may not clean as thoroughly as the scrubbing
type cleaner.
Cassettes are subject
to wear and the,sound quality and may degrade over
time. Always make sure that the cassette tape is
in good condition before
you have your tape player serviced.
Care of Your Compact Discs
Handle discs carefully. Store them in their original cases or other
protective cases and away from direct sunlight and dust. If the surface
of
a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent
solution and clean it, wiping from the center
to the edge.
Be sure never
to touch the signal surface when handling discs. Pick up
discs by grasping the outer edges or the edge of the hole and the
outer edge.
174
r

Downloaded from www.Manualslib.com manuals search engine - You should asK your service station operators if their gasolines contain
deposit control additives and oxygenates, and
if they have been
reformulated to reduce vehicle emissions.
- FUELS IN FOREIGN COUNTMES
If you plan on driving in another country outside the U.S. or Canada,
.+- unleaded fuel may be hard to find. Do not use leaded gasoline. If you use
even one tankful, your emission controls won’t work well or at all. With
continuous use, spark plugs can get fouled, the exhaust system can
-- corrode, and your engine oil can deteriorate quickly. Your vehicle’s
oxygen sensor will be damaged. All
of that means costly repairs that
wouldn’t be covered by your warranty.
~ To check on fuel availability, ask an auto club, or contact a major oil
company that does business in the country where you’ll be driving.
You can also write us at the following address for advice. Just tell us
__ where you’re going and give your Vehicle Identification Number (VIN).
General Motors Overseas Dist:ribution Corporation,
North American Export Sales (NAES)
1908 Colonel Sam Drive
Oshawa, Ontario
L1H 8P7
---. FUEL ECONOMY
Your fuel economy (miles per gallon or liters per 100 kilometers) can vary
have been driven through a standard test and their actual fuel economy
was recorded. These readings were adjusted and printed on the fuel
economy window sticker which was attached to your new Cadillac when it
-- was delivered and in the Gas Mileage Guide which is available from your
dealership.
~. depending on how your Cadillac is driven. Several vehicles like yours
The fuel economy estimates are based on results
of tests required by the
U. S. Environmental Protection Agency (EPA). These tests are used to
certify that vehicles meet the Federal emissions and fuel economy
standards. Cadillac tests prototypes of new vehicles and submits the
- results to the EPA. The EPA then confirms the accuracy of the figures
provided by Cadillac. The vehicles are driven by a professional driver
under controlled laboratory conditions, on an instrument similar
to a
w.
25 1

Downloaded from www.Manualslib.com manuals search engine Here are some cleaning tips:
Always read the instructions on the cleaner label.
Clean up stains as soon as you can -- before they set.
Use a clean cloth or sponge, and change to a clean area often. A soft
brush may be used
if stains are stubborn.
Use solvent-type cleaners in a well-ventilated area only. If you use
them, don’t saturate the stained area.
If a ring forms after spot cleaning, clean the entire area immediately
or it will set.
Cleming Leather
Use a soft cloth with lukewarm water and a mild soap or saddle soap.
For stubborn stains, use a mild solution of
10% isopropyl alcohol
(rubbing alcohol) and
90% water.
Never use oils, varnishes, solvent-based or-abrasive cleaners; furniture
Soiled leather should be cleaned immediately. If dirt is allowed to
polish or shoe polish on leather.
work into finish, it can harm the leather.
Cleaning Speaker Covers
Vacuum around a speaker cover gently, so that the speaker won’t be
damaged. If something gets.on one
of them, follow the steps earlier under
“Using Solv.ent-Type Cleaner on Fabric.’’ Use as little solvent as
you can.
Using Foam-Ppe Cleaner on Fabric
Vacuum and brush the.area to remove any loose dirt.
0 Always clean a whole trim panel or section. Mask surrounding trim
Mix Multi-Purpose Powdered Cleaner following the directions on the
along stitch
or welt lines.
container label.
IC-
7-.
0 Use suds only and apply with a clean sponge.
0 Don’t saturate the material.

Downloaded from www.Manualslib.com manuals search engine 0 Don’t rub it roughly.
0 As soon as you’ve cleaned the section, use a sponge to remove the
suds.
Rinse the section with a clean, wet sponge.
0 Wipe off what’s left with a slightly damp paper towel or cloth.
Then dry it immediately with a blow dryer or a heat lamp.
NOTICE:
Be careful with a hair dryer or heat lamp. You could scorch the
fabric.
Wipe with a clean cloth.
Using Solvent-Type Cleaner on Fabric
.-
.-
First, see if you have to use solvent-type cleaner at all. Some spots and
stains
will clean off better with just water and mild soap.
If you need to use a solvent:
Gently scrape excess soil from the trim material with a clean, dull
knife or scraper. Use
very little cleaner, light pressure.and clean cloths
(preferably cheesecloth). Cleaning should start at the outside of the
stain, “feathering” toward
the center. Keep changing to a clean
section of the cloth.
When you clean a stain from fabric, immediately dry the area with an
air hose, hair dryer, or heat lamp
to help prevent a cleaning ring. (See
the previous NOTICE.)
303

Downloaded from www.Manualslib.com manuals search engine Special Cleaning Problems
Greasy or Oily Stains
Such as grease, oil, butter, margarine, shoe polish, coffee with cream,
chewing gum, cosmetic creams, vegetable oils, wax crayon, tar and
asphalt.
0 Carefully scrape off excess stain.
0 Follow the solvent-type instructions described earlier.
0 Shoe polish, wax crayon, tar and asphalt will stain if left on a vehicle
seat fabric. They should be removed as soon as possible. Be careful,
because the cleaner
will dissolve them and may cause them to spread.
Non-Greasy Stains
Such as catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks,
wine, vomit, urine and blood.
Carefully scrape off excess stain, then sponge the soiled area with cool
If a stain remains, follow the foam-type instructions described earlier.
If an odor lingers after cleaning vomit or urine, treat the area with a
waterbaking soda solution:
1 teaspoon (5 ml) of baking soda to 1 cup
(250 ml) of lukewarm water.
water.
If needed,
clean lightly with solvent-type cleaner.
Combination Stains
Such as candy, ice cream, mayonnaise, chili sauce and unknown stains.
Carefully scrape off excess stain, then clean with cool water and allow
If a stain remains, clean it with solvent-type cleaner.
to
dry.
I.
c-r
t
r_
L.

Downloaded from www.Manualslib.com manuals search engine The cast aluminum pistons use two compression rings and one oil control
ring. The pistons are tin plated to provide a non-scuffing surface when
the engine is new.
c_ A steel camshaft is supported by five steel backed babbit bearings. It is
driven by the crankshaft through a chain at
the front of the engine. The
give gear is keyed to the crankshaft and the driven sprocket is bolted to
the camshaft. Both the crankshaft gear and camshaft sprocket have
locating marks to provide the correct valve timing and timing chain
installation.
The valve lifters are roller hydraulic type and are positioned
in the aluminum lifter carrier.
-1_
-
4T60E Transaxle
The Hydra-Matic 4T60E 4-speed overdrive, electronic transaxle consists
primarily of a five element torque converter,
two planetary gear sets,
-- various clutches, final drive assembly, and a control valve body.
321
~. .

Downloaded from www.Manualslib.com manuals search engine 4.9 LITER ENGINE
Displacement ............................... 4.9L (300 cu. in.)
No. of Cylinders .............................. 8 - 90 Degree V
Power (Acc. to
SAE 51349) ............... 200 (bhp) @ 4100 rpm
Torque
(Acc. to SAE 51349) ............ 275 (lbs. ft.) @ 3000 rpm
Bore
....................................... 92mm (3.623 in.)
Stroke
..................................... 92mm (3.623 in.)
Compression Ratio
.................................... 9.5:l
Cylinder Block
...... Die Cast Alumbum with Iron Cylinder Bores
Cylinder Heads Cast Iron
Intake Manifold
.............................. Cast Aluminum
Lifter Trpe
................................. Roller Hydraulic
Intake Valve Head Diameter
.................. 45mm (1.772 in.)
Exhaust Valve Head Diameter
................. 38mm (1.496 in.)
Pistons
...................................... Cast Aluminum
Firing Order
.................................. 1-8-4-3-6-5-7-2
Left Bank
.......................................... 1-3-5-7
Right Bank
......................................... 2-4-6-8
Camshaft
............................................. Steel
Camshaft Drive
...................................... Chain
Crankshaft Material
..................... Pearlitic Nodular Iron
Main Bearings
......................................... Five
...................................... 250 (kW) @ 4100 rpm
...................................... 375(N.m) @ 3000 rpm
.. - .- :.,-< ...................................
ENGINE LUBRICATION SYSTEM
Type of Intake ..................................... Stationary
Filter System
...................................... Full-Flow
Oil Pump
........................................... Geroto
326

Downloaded from www.Manualslib.com manuals search engine EXhlAUST SYSTEM
Type ............................... Single with Crossover Pipe
Muffler
.................................. One-Reverse Flow
Resonator
............................................ None
Exhaust Pipe
.................................. .Stainless Steel
Intermediate Pipe
............................. ,- Stainless Steel
Tail Pipe
..................................... Stainless Steel
ELECTHCA SYSTEM
Voltage ................................................ 12
Generator ......................................... 140Amp
Ground
........................................... Negative
AIR CONRITIONING SYSTEM
Refrigerant-R134a ............................ .2.0 lbs. (.91 kg)
Not all air conditioning refrigerants are the same.
If the air conditioning
system in your vehicle needs refrigerant, be sure the proper refrigerant is
used. If you’re not sure, ask your Cadillac dealership.
FLUID CAPACITIES
Transaxle (4T60E) .............................. 20 pts. (9.5 L)
Engine Oil ................................... 5.0 qts. (4.7 L)
With Filter Change ............................ 5.5 qts. (5.2 L)
Engine Cooling System ......................... 11 qts. (10.5 L)
Fuel Tank .................................. 20 gallons (76 L)
Power Steering .............................. 1.3 quarts (1.2 L)
Windshield Washer Reservoir .................. 4.2 quarts (4.1 L)
TIGHTEN TORQUE
Spark Plugs ............................... .20 Nm (15 lbs. ft.)
Oil Pan Drain Plug. ......................... 30N.m (22 lbs. ft.)
328
tl
r_
.c-
FC