1994 CADILLAC DEVILLE clutch

Downloaded from www.Manualslib.com manuals search engine r I
r i
r‘ I
!- I
r
? ! i
!- i
I
r‘ L
DlSTR SIR PCM (IGN) INJ INJ IGN 1
]mmmmmmri
~mnmmmml
PCM (BAT) RTD BATT A/C COMP HDLPS STOP LP TURN/HAZ
DRL
L HDLP LO
R HDLP LO L HDLP HI R HDLP HI IGN 3 COOL FAN TRANS
I FUSE CENTER IDENTIFICATION
ENGINE COMPARTMENT FUSE BLOCK
DISTR 20A TURN/HAZ 20A
SIR 20A - IGNITION CONTROL MODULE - HAZARD FLASHER
- DIAGNOSTIC/ENERGY RESERVE
- DUAL POLE ARMING SENSOR - DAYTIME RUNNING LIGHTS (CANADA)
- TURN FLASHER RELAY - TURN FLASHER MODULE
MODULE (DERM) DRL 10A (CANADA)
PCM IGN) 10A DRL 10A (CANADA)
- PASS-Key@ DECODER MODULE HTD W/S 1OA
INJ 1OA - HEATED WINDSHIELD CONTROL MODULE
INJ 1OA - LEFT REAR STRUT
IGN 1 10A
- P6WERTRAIN CONTROL MODULE (PCM) - LEFT AND RIGHT LO BEAM HEADLAMP
- 1,4,6, AND 7 FUEL INJECTORS LR STRUT 1OA
- 2,3,5, AND 8 FUEL INJECTORS RR STRUT 10A
- A/C REFRIGERANT PRESSURE SWITCH - TRANSAXLE RANGE SWITCH - STOP/BTSI/CRUISE BRAKE SWITCH - INSTRUMENT PANEL CLUSTER - KEYLESS ENTRY MODULE - DIAGNOSTIC/ENERGY RESERVE MODULE
- RIGHT REAR STRUT LF STRUT 1OA
RF STRUT 1OA
L HDLP LO 1OA
R HDLP LO 10A
L HDLP HI 1OA
R HDLP HI 1OA
IGN 3 10A
- LEFT FRONT STRUT
- RIGHT FRONT STRUT
- LEFT LO BEAM HEADLAMP
- RIGHT LO BEAM HEADLAMP
- LEFT HI BEAM HEADLAMP
- RIGHT HI BEAM HEADLAMP
- REAR DEFOGGER RELAY - ELECTRONIC LEVEL CONTROL (ELC) - HEATED WINDSHIELD - HEATER AND A/C PROGRAMMER - CRUISE CONTROL
LFR2RING
LIGHTS
-
- TURN/HAZARD SWITCH ASSY - CHIME MODULE - HEADLIGHT SWITCH - TWILIGHT SENTINEUDRL MODULE
- FUELPUMP - OIL PRESSURE SWITCH - POWERTRAIN CONTROL MODULE (PCM)
FUEL PUMP 20A
PCM BAT) 10A
RTD (BAT) 20A
A/C COMP 1OA
- POWERTRAIN CONTROL MODULE (PCM)
HDLPS 30A
- P6WERTRAIN CONTROL MODULE pCM) COOLING FAN 1OA - ROAD SENSING SUSPENSION (RSS) MODULE - EXTENDED TRAVEL BRAKE SWITCH
- A/C COMPRESSOR CLUTCH - COOLING FAN RELAYS 1,2, AND 3.
- HEADLIGHT DIMMER SWITCH - HEADLIGHT RELAY “D” (ENGINE COMP MICRO - OVERSPEED ALERT MODULE (EXPORT)
- DRL HEADLIGHT RELAY “E (WITH DAYTIME - POWER STEERING PRESSURE SWITCH - EXHAUST GAS RECIRCULATION (EGR) VALVE
- POWERS C13 - TRANSAXLE SHIFT SOLENOIDS A & B - EVAPORATIVE EMISSION CONTROL SOLENOID
- STOP/BTSI/CRUISE SWITCH - POWERTRAIN CONTROL MODULE (PCM)
- STOPLIGHT SWITCH CAPACITOR - TORQUE CONVERTER CLUTCH SOLENOID - TCC BRAKE SWITCH
- FRONT AND REAR HEATED OXYGEN SENSOR TRANS/ECS 1 OA
RELAY CENTER)
RUNNING LIGHTS)
STOP LP 20A
315

Downloaded from www.Manualslib.com manuals search engine The cast aluminum pistons use two compression rings and one oil control
ring. The pistons are tin plated to provide a non-scuffing surface when
the engine is new.
c_ A steel camshaft is supported by five steel backed babbit bearings. It is
driven by the crankshaft through a chain at
the front of the engine. The
give gear is keyed to the crankshaft and the driven sprocket is bolted to
the camshaft. Both the crankshaft gear and camshaft sprocket have
locating marks to provide the correct valve timing and timing chain
installation.
The valve lifters are roller hydraulic type and are positioned
in the aluminum lifter carrier.
-1_
-
4T60E Transaxle
The Hydra-Matic 4T60E 4-speed overdrive, electronic transaxle consists
primarily of a five element torque converter,
two planetary gear sets,
-- various clutches, final drive assembly, and a control valve body.
321
~. .

Downloaded from www.Manualslib.com manuals search engine c-
The torque converter houses a pump, turbine, pressure plate which is
splined to the turbine, and a stator assembly, serving as a fluid coupling, it
smoothly transmits power from the engine to the transaxle. It also
hydraulically provides a additional torque when required. When applied,
the pressure plate provides a mechanical torque when required. When
applied, the pressure plate provides a mechanical direct drive coupling of
the engine to the transaxle.
-
n
The two planetary gear sets provide the four forward gear ratios and
reverse. Changing of the gear ratios is fully automatic and is
accomplished through the use of various electronic and mechanical
requirements. Four multiple disc clutches, two roller clutches, a sprag
clutch, and three bands provide the friction elements required to obtain
the various ratios with the planetary gear sets.
A hydraulic system (the control valve body) pressurized by a vein type
pump provides the working pressure needed to operate the friction
elements and automatic controls.
Front Suspension
Your fully independent front suspension is a combination strut and spring
design. The frame is isolated from the body with six rubber mounts.
r

Downloaded from www.Manualslib.com manuals search engine Ly ENGINE COOLING SYSTEM
Radiator Cap Relief Pressure ................. 15.0 psi (103 kPa)
Thermostat Starts To Open
................ 192-199'F (89-93OC)
Water Pump Type
................................. Centrifugal
Drive Belt
....................................... Serpentine
Radiator Core
................................... Aluminum
Radiator Cooling Fans (2)
............................ Electric
FUEL SYSTEM
Induction Type ............ Sequential Port Fuel Injection (SPFI)
System Pressure
.................... .33.4-43.5 psi (230-300 kPa)
Idle Speed
.................................. ECM Controlled
Filter Type
............................... Paper Type Element
Fuel Pump
................................ Electric (In Tank)
Fuel Required ................. Premium Unleaded (91 Octane)
AUTOMATIC TRANSAXLE
Trade Name ............................. Hydra- Matic 4T60E
Type ..................................... 4-Speed Automatic
.................................... Viscous Converter Clutch
Fluid Required
............... DEXRON IIE@or DEXRON HI@
Axle Ratio
........................................... 2.73:l
EMISSION CONTROL SYSTEMS
Exhaust Gas Recirculation .................... Controlled Flow
Catalytic Converter
......................... Ceramic Monolith
Evaporative Emission Control
................ Charcoal Canister
Crankcase Emission Control
....................... PCV Valve
Electronic System
..................... Open and Closed Loop
327
-