1994 CADILLAC DEVILLE engine

Downloaded from www.Manualslib.com manuals search engine 3. Pick up the latch plate and pull the belt across you. Don’t let it get
4. Push the latch plate into the buckle until it clicks.
twisted.
Pull
up on the latch plate to make sure it is secure. If the belt isn’t long
enough, see “Safety Belt Extender” at the end of this section.
Make sure the release button on the buckle is positioned so you would
be able to unbuckle the safety belt quickly if you ever had to.
r

Downloaded from www.Manualslib.com manuals search engine The lap part of the belt should be worn low and snug on the hips, just
touching the thighs. In a crash, this applies force to the st\
rong pelvic
bones. And you'd be less likely to slide under the lap belt. If
you slid
under it, the belt would apply force at your abdomen. This could cause
serious
or even fatal injuries. The shoulder belt should go over the
shoulder and across the chest. These parts
of the body are best able to
take belt restraining forces.
The safety belt locks if there's a sudden stop or crash.
21

Downloaded from www.Manualslib.com manuals search engine Shoulder Belt Height Adjuster
.1
1
YOU can move tne
shoulder belt adjuster
to the height that
is
right for you.
To move it up or
down, squeeze the
release handle. When
you release the
handle,
try to move it
down a little to make
sure it has locked into
position.
You
can move the
adjuster up from
a
lower position by
pushing the bottom
of the release handle.
r-
t-4
22

Downloaded from www.Manualslib.com manuals search engine Adjust the height so
that the shoulder
portion of the belt is
properly positioned on
your shoulder, away
from your face and
To help you find a height that is right for you, follow these guidelines:
For a tall person: Use
the upper or upper-middle position.
For a person
of average height: Use a position somewhere in the middle.
For a short person: Use the lower
or lower-middle position.
~

Downloaded from www.Manualslib.com manuals search engine Shoulder Belt Tightness Adjustment
Your vehicle has a shoulder belt tightness adjustment feature. If the
shoulder belt seems too tight, you can adjust it
like this:
1. Sit well back in the seat.
2. Star
shol 't
pulling the
dder belt out.
3. Just before it
reaches the end,
give it
a quick
pull.
24
-.
.-
*b
I-
&_ .

Downloaded from www.Manualslib.com manuals search engine 4. Let the belt go back all the way. You should hear a slight clicking
sound.
If you don’t, the adjustment feature won’t set, and you’ll have
to start again.
5. Now you can add a small amount of slack. Lean forward slightly, then
sit back.
If you’ve added more than 1 inch (25 mm) of slack, pull the
shoulder belt out as you did before and start again.
If you move around in the vehicle enough, or if you pull out the shoulder
belt, the belt will become tight again.
If this happens, you can reset it. .-
.-

Downloaded from www.Manualslib.com manuals search engine Q: What's wrong with this?
A: The shoulder belt is too loose. It won't give nearly as much
protection this way.
I
A CAUTION:
You can be serious$ hurt if your shoulder belt is too loose. In a
crash you would move forward too much, which could increase
injury.. The shoulder belt
should fit against your body. Don't
allow more than
1 inch (25 mm) of slack.
I-
26

Downloaded from www.Manualslib.com manuals search engine Q: What’s wrong with this?
n
A: The belt is buckled in the wrong place.
A CAUTION:
You can be seriously injured if your belt is buckled in the wrong
place like this.
In a crash, the belt would go up over your
abdomen. The belt forces would
be there, not at the pelvic
bones. This could cause serious internal injuries. Always buckle
your belt into the buckle nearest you.
27