1994 BUICK CENTURY light

Ignition Key Positions
C
9.5 B
A i E
With the ignition key in the ignition switch, you can turn
the switch to five positions:
(A) Accessory: An “on” position in which you can
operate your electrical power accessories. Press
in the
ignition switch as you turn the top
of it toward you.
(B) Lock: The only position in which you can remove
the key. This locks
your steering wheel, ignition and
transaxle.
(C) Off: Unlocks the steering wheel, ignition, and
transaxle, but does not send electrical power
to any
accessories. Use this position
if your vehicle must be
pushed or towed, but never
try to push-start your
vehicle.
A warning chime will sound if you open the
driver’s door when the ignition is off and the
key is in
the ignition.
(D) Run: An ‘‘on’’ position to which the switch returns
after you start your engine and release
the switch. The
switch stays
in the “Run” position when the engine is
running. But even when the engine is
not running, you
can use
“Run” to operate your electrical power
accessories, and to display some instrument panel
warning lights.
(E) Start: Starts the engine. When the engine starts,
release the key. The ignition switch will return
to “Run”
for normal driving.
ProCarManuals.com

c
0 1 (First Gear)
This position gives you even more power (but lower
fuel economy) than
“2.” You can use it on very steep
hills, or in deep snow or mud. If the selector lever is
put in
“1,” the transaxle won’t shift into first gear
until the vehicle
is going slowly enough.
NOTICE:
If your front wheels can’t rotate, don’t try to
drive. This might happen if you were stuck
in
very deep sand or mud or were up against a solid
object. You could damage your transaxle.
Also, if you stop when going uphill, don’t hold
your vehicle there with only the accelerator
pedal. This could overheat and damage the
transaxle. Use your brakes to hold your vehicle
in position on a hill.
Parking Brake
To set the parking brake:
Hold the regular brake
pedal down with your right
foot. Push down the
parking brake pedal with
your left foot.
If the
ignition is on, the brake
system warning light will
come on.
To release the parking
brake:
Hold the regular
brake pedal down. Pull the
brake release lever.
ProCarManuals.com

Turn SignallHeadlight Beam Lever
.1
The lever on the left side of the steering column
includes your:
Turn Signal and Lane Change Indicator
0 Headlight High-Low Beam & Passing Signal
a Windshield Wipers
0 Windshield Washer
Cruise Control (Option)
Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for
left) positions. These positions allow you
to signal a turn or a lane change.
To signal a
turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
89
ProCarManuals.com

I I A green arrow on the
instrument panel will flash
in the direction of the turn
or lane change.
To signal a lane change,
just raise
or lower the lever
until the green arrow starts
to flash. Hold
it there until
you complete your lane
change. The lever will
return by itself when you
release it.
As you signal a turn or a lane change, if the arrows don’t
flash but just stay on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace
it to help avoid an
accident. If the green arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses” in the Index)
and for burned-out bulbs.
nrn Signal Reminder
If your turn signal is left on for more than 3/4 of a mile,
a chime will sound.
To turn off the chime, move the turn
signal lever
to the off position.
Operation of Lights
Although your vehicle’s lighting system (headlights,
parking lights, fog lamps, side marker lights and
taillights) meets all applicable federal lighting
requirements, certain states and provinces may apply
their own lighting regulations that may require special
attention before you operate these lights.
For example, some jurisdictions may require that you
operate your fog lamps only when your lower beam
headlights are also on, or that headlights be turned on
whenever you must use your windshield wipers. In
addition, most jurisdictions prohibit driving solely with
parking lights, especially at dawn
or dusk. It is
recommended that you check with your own state or
provincial highway authority for applicable lighting
regulations.
90
ProCarManuals.com

Headlight High-Low Beam
BRIGHT
To change the headlights
from low beam to high
or
high to low, pull the turn
signal lever all the way
toward you. Then release it.
When the high beams are
on, this blue light on the
instrument panel also will
be on.
Windshield Wipers
You control the windshield wipers by turning the band
marked “WIPER.”
For a single wiping cycle, turn the band to “MIST.”
Hold it there until the wipers start, then let go. The
wipers will stop after one cycle.
If you want more
cycles, hold the band on
“MIST” longer.
91
ProCarManuals.com

You can set the wiper speed for a long or short delay
between wipes. This can be very useful in light rain
or
snow. Turn the band to choose the delay time. The
closer to
“LO,” the shorter the delay.
For steady wiping at low speed, turn the band away
from you
to the “LO” position. For high speed wiping,
turn the band further, to “HI.”
To stop the wipers, move
the band to
“OFF.”
Remember that damaged wiper blades may prevent you
from seeing well enough to drive safely. To avoid
damage, be sure
to clear ice and snow from the wiper
blades before using them. If they’re frozen to the
windshield, carefully loosen or thaw them.
If your
blades do become damaged, get new blades
or blade
inserts.
Heavy snow or ice can overload your wiper motor.
A
circuit breaker will stop the motor until it cools. Clear
away snow or ice to prevent an overload.
Windshield Washer
At the top of the turn signalheadlight beam lever there’s
a paddle with the word “PUSH” on it.
To spray washer
fluid on the windshield, push the paddle.
If you push the paddle less than one second, washer
fluid will spray three
to four times while the wiper
blades
cycle. If you push the paddle longer than one
second, washer fluid will spray as long
as the paddle is
held. When
you release the paddle, the wiper blades will
cycle three to four more times to clear the window and
then either stop or return to your preset speed.
Driving without washer fluid can be dangerous.
A bad
mud splash can
block your vision. You could hit another
vehicle or go off the road. Check your washer fluid level
often.
92
ProCarManuals.com

To Set Cruise Control
1. Move the Cruise
Control switch
to “ON.”
2. Get up to the speed you want.
CRUISE
3. Push in the “SET”
button at the end of the
lever and release it.
4.
5.
The CRUISE light on
the instrument panel
will come on.
Take your foot
off the
accelerator pedal.
95
ProCarManuals.com

To Get Out of Cruise Control
There are two ways to turn
off the Cruise Control:
-
1. Step lightly on the brake
pedal,
OR
2. Move the Cruise switch
to
“OFF.”
To Erase Speed Memory
When you turn off the Cruise Control or the ignition,
your Cruise Control set speed memory is erased.
Lights
I These switches control the
following light systems:
Headlights
Parking Lights
Side Marker Lights
Taillights
License Plate Lights
Instrument Panel Lights
To turn on the headlights, press the switch with the light
symbol.
Press the switch marked
“P’ to turn on the parking
lights.
Press
“OFF” to turn off all lights.
98
ProCarManuals.com