1993 PONTIAC GRAND-PRIX tow

Leaving Your Vehicle With the
Engine Running
(AUTOMATIC TRANSAXLE)
It is dangerous to leave your
vehicle with the engine
running. Your vehicle could move suddenly
if the shift lever is not
fully in P (Park) with the parking
brake firmly set. And, if you leave
the vehicle with the engine running,
it could overheat and even catch
fire.
You or others could be injured.
Don't leave your vehicle with the
engine running unless
you have to.
If you have to leave your vehicle with
the engine running, be sure
your vehicle
is in P (Park) and your parking brake is
firmly set before you leave it. After
you've moved
the shift lever into the
P (Park) position, hold tbe regular
bralre pedal down. Then, see
if you can
move the shift lever away from P (Park)
without first
pulling it toward you (or, if
you have the console shift lever,
without first pushing the button).
If you
can, it means that the shift lever wasn't
hlPy locke'd into P (Park).
Parking Your Vehick
(MANUAL TRdNSAXLE)
Before you get out of your vehicle,. put
your manual transaxle in R (Reverse)
and firmly apply the parking brake.
If
you are parking on a hill, see the
Index under Parking an Mills.
ProCarManuals.com

(Continued)
is not hlly in P (Park) with the
parking brake firmly set. Your
vehicle can roll. Don’t leave pur
vehicle when the engine is running
unless you have to. If you’ve left
the engine running, the vehicle can
move suddenly. You or others
could be injured. To be sure your
vehicle
won’t move, even when
you’re on fairly level ground, always
set your parking brake and move
the
shift lever to P (Park).
If you are parking on a hill, or if
you’re pulling a trailer, also see the
In&x under Parking on Hills or
Towing a Tnzileu.
.- i ,- - . I.
Horn
You can sound the horn by pressing the
horn symbols on your steering wheel.
Tilt Steering Wheel (omow
A tilt steering wheel allows you to
adjust the steering wheel before
you
drive. You can also raise it to the
highest level
to give your legs more
room when you exit and enter the
vehicle.
To tilt the wheel, hold the steering
wheel and pull the lever.
Move the
steering wheel to
a comfortable level,
then release the lever to
lock the wheel
in place.
ProCarManuals.com

Dayfime Running lights
(CANADA ONLY)
The Canadian Federal Government has
decided that “Daytime Running Lights”
(DRL) are a useful feature, in that DRL
can make your vehicle more visible to
pedestrians and other drivers during
daylight hours. DRL are required
on
new vehicles sold in Canada.
Your DRL work with a light sensor on
top of the instrument panel. Don’t
cover it up.
The low beam headlights will come on
at reduced brightness in daylight when:
The ignition is on
The headlight switch is off, and
The parking brake is released. At
dusk, the exterior lights will come
on
automatically and the low beams will
change to full brightness. At dawn, the
exterior lights will go out and the low
beams will change to the reduced
brightness
of DRL (if the headlight
switch is off).
Of course, you may still turn on the
headlights any time you need to.
To idle your vehicle with the DRL off,
set the parking brake while the ignition
is in the
Off or Lock position. Then
start the vehicle. The DRL will stay
off
until you release the parking brake.
Headlighf High-Low Beam
Changer
To change the headlights from low
beam to high or high to low, pull the
turn signal/headlight beam lever all the
way toward
you. Then release it.
When the high beams are on, a blue
light on the instrument panel
also will
be on.
ProCarManuals.com

Features & Controls
Flash-to- Pass
Flash-to-pass lets you use your high
beam headlights to signal a driver in
front of you that you want to pass.
To use it, pull the turn signal/headlight
beam lever toward you.
If Your Headlights are Off:
Your high beam headlights will turn on.
They’ll stay on as long as you hold the
lever there. Release the lever to turn
them off.
If Your Headlights are On:
No flash-to-pass. Use the lever to
change between high and low beams, as
explained under
Headlight High-Low
Beam Changer earlier in this section.
If the fog light switch is on, your fog
lights will go off while the high beams
are
on. When the high beams go off, the
fog lights will come on again.
30
Brightness Intensity Control
You can brighten or dim the instrument
panel lights by sliding the control knob
up or down.
If you slide the knob all the
way up to
INT your courtesy or interior
lights will come on.
To turn instrument
panel lights on to full intensity with the
headlights on, slide the control knob to
HI.
Fog Lights
Use your fog lights for better vision in
foggy or misty conditions.
To turn fog lights on, push the switch.
Pull the parking light switch to turn the
fog lights off.
When using fog lights, the parking lights and/or low beam headlights must
be on.
The fog lights will go off whenever the
high beam headlights come on. When
the high beams go off, the fog lights will
come
on again.
ProCarManuals.com

Illuminated Entry (OPTION)
If you have illuminated entry, your
interior lights will stay on for about
12
seconds after the door is closed.
The lights will go out when the ignition
key is turned to the
Run position.
Inside Manual DaylNight
Rearview Mirror
To reduce glare from lights behind you,
pull the lever toward you to the night
position.
Convex Outside Mirror
Your right side mirror is convex. A
convex mirror’s surface is curved so yo^
can see more from the driver’s seat.
A
If you aren’t used to a convex
mirror, you can hit another
vehicle.
A convex mirror can make
things (like other vehicles) look
farther away than they really are.
If
you cut too sharply into the right
lane, you could hit
a vehicle on
your right. Check your inside
mirror or glance over
your shoulder
before changing lanes.
a:
1
I
...
ProCarManuals.com

Trunk Access Panel
If you have split rear seats, you may
have a trunk access panel for storing
long objects like skis. Pull your rear
armrest down using the strap. Then pull
the latch on the trunk access panel
toward you to open the panel.
To close the access panel, lift the latch.
Ashtrays and Lighter
To clean the center console ashtray,
open the lid and then lift it out
by
pulling on the snuffer.
To clean the instrument panel ashtray,
open it fully and lift it out
by pulling on
the ashtray door.
The lighter is next
to the center front
ashtray.
To use the lighter, just push
in all the way and let go. When it’s
ready, it will pop back
by itself. it
87
U
11.
ProCarManuals.com

Voltmeter (OPTION)
When the engine is running, the gage
shows the condition
of the charging
system. Readings between the red
warning zones indicate the normal
operating range.
Readings in either red warning zone
indicate a possible problem in the
electrical system. Have your vehicle
serviced immediately.
When your engine
is not running, but
the ignition is
on (in the Run position),
the gage shows your battery’s state
of
charge.
Brake System Warning Light
Your Pontiac’s hydraulic brake system
is divided into two parts. If one part
isn’t working, the other part can still
work and stop you. For good bralung,
though, you need both parts working
well.
If the warning light goes on, there
could be a brake problem.
Have your brake system inspected right
away.
This light should come on as you start
the vehicle.
If it doesn’t come on then,
have it fixed
so it will be ready to warn
you
if there’s a problem.
This light will also come on when you
set your
parking brake, and will stay on
if your parking brake doesn’t release fully.
If it stays on after your parking
brake is fully released, it means you
have a brake problem.
If the light comes on while driving, pull
off the road and stop carefully. You maJ
notice that the pedal is harder to push.
Or, the pedal may
go closer to the floor.
It may take longer to stop.
If the light is
still on, have the vehicle towed for
service. (See the
Index under Towing
Your Pontiac.)
1 CAUTION
Your brake system may not
be working properly if the .
WIMC warning light is on. Driving
with the brake warning light ora can
lead to an accident. If the light is
still on after you’ve pulled off the
road and stopped carefully, have
I the vehicle towed €or senrice.
ProCarManuals.com

_1
To adjust the HUD so you can see it
properly:
1. Start your engine and slide the HUD
dimmer control (to the right
of the
steering wheel, below the wiper/
washer control) all the way to
HI.
The brightness of the HUD image is
determined
by whether the headlight
switch is on or off, and where you
have set the HUD dimmer control.
2. Adjust the seat, if necessary, before
setting the height control. Slide the
HUD image height control all the
way toward you, raising the image as
far as possible, Then slide the HUD
image height control away from you
so the image is as low as possible but
in full view.
3. Slide the dimmer control toward
OFF until the HUD image is no
brighter than necessary. To turn the
HUD off, slide the HUD dimmer
control to OFF. If the
sun comes out,
or it becomes cloudy,
or if you turn
on your headlights,
you may need to
adjust the HUD’s brightness
using
the HUD dimmer control. Polarizing
sunglasses could make
the HUD
image harder to see.
If the HUD image is too
1 L bright, or too high in your
field of view, it may take you more
time to see things you need to see
when it’s dark outside. Be sure to
keep the HUD image dim and
placed low in your field of view.
ProCarManuals.com