1993 MITSUBISHI 3000GT key

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Ignition Switch54-7REMOVAL SERVICE POINTS
+A, STEERING WHEEL REMOVAL
Remove the steering wheel by using the special tool.
Caution
Do not hammer on the steering wheel to remove it;
doing so may damage the collapsible mechanism.
Front of vehicles
219FO12:
+B,COLUMN COVER LOWER / COLUMN COVER
UPPER REMOVAL
After the screws have been removed, remove the covers,while making sure not to break the grippers.
+C, STEERING LOCK CYLINDER REMOVAL
(1) Insert the ignition key into the steering lock cylinderand place the key in the ACC position.
(2)Press the lock pin down with a Phillips head screwdriv-
er (small-size one) to remove the steering lock cylinder.INSTALLATION SERVICE POINT
.A+COLUMN SWITCH AND CLOCK SPRING
ASSEMBLY INSTALLATIONLine up the “NEUTRAL” mark of the clock spring with
the mating mark to center the clock spring.
CautionIf the clock spring is not centered, problems such
as intermediate failure of the steering wheel to turn,broken ribbon cable in the clock spring, or the like
could occur. As a result, they might hinder proper
operation of the SRS, resulting in serious injury.
iI
1 TSB RevisionI

Downloaded from www.Manualslib.com manuals search engine 54-8CHASSIS ELECTRICAL - Ignition Switch
216AO57000002296INSPECTION
IGNITION SWITCH CHECK
(1) Remove the knee protector, the column cover lower andd’
the column cover upper. (Refer to GROUP 52A - Instru-
ment Panel.)
(2) Disconnect the wiring connector from the ignition switch
and key reminder switch, and connect an ohmmeter to
the switch side connector.(3) Operate the switch, and check the continuity between
the terminals.
PositionKeyConnector AConnector B
LOCK
ACC
ON
START
ConnectorB
ignitionkey
illumina-
tion light
terminal
No.
415
LJ
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-18CHASSIS ELECTRICAL - Meters and Gauges
OPERATION
l
When the ignition key is at the “ON” position,the fuel gauge is activated.
l
When there is much fuel, the unit’s resistanceis small and the current flowing in the circuit
is great, so the gauge’s indicator indicates inthe “F” area.
l When there is little fuel, the unit’s resistance
is high and the current flowing in the circuit
is small, so the gauge’s indicator indicates inthe
“E” area.

lWhen the ignition key is at the “ON” position,
the engine coolant temperature gauge is acti-
vated.l
When the engine coolant temperature is high,
the unit’s resistance is low and there is a greatflow of current in the circuit, so the gauge’s
indicator indicates in the “H” area.
l
When the engine coolant temperature is low,
the unit’s resistance is high and there is a smallflow of current in the circuit, so the gauge’s
indicator indicates in the “C” area.
/Speed sensor (electrical speedometer type)>l Pulses are produced in accordance with the
vehicle speed, and vehicle-speed signals areinput to systems (the MFI system, etc.) that
regulate according to the vehicle speed.
TROUBLESHOOTING HINTS
1.The fuel gauge doesn’t function, or shows the
incorrect indication.
(1) Disconnect the connector of the fuel pumpand gauge unit assembly; the ‘F” side is
indicated when terminal (5) is then
grounded.l Check the fuel gauge.
2.The engine coolant temperature gauge doesn’t
function, or shows the incorrect indication.
(1)The “l-l” side is indicated when the connector
of the engine coolant temperature gauge
unit is disconnected and then grounded.l
Check the engine coolant temperature
gauge unit.
3. Systems dependent upon control according to
the vehicle speed do not function correctly.l Check the reed switch (mechanical
speedometer type)l Check the speed sensor (electrical
speedometer type)
coil pressure gauge>l
When the ignition key is at the “ON” position,
the oil pressure gauge is activated.
lWhen oil pressure is high, the internal contacts
of the gauge unit are kept closed for a longerperiod of time. This causes more current to
flow in the circuit, and the gauge pointer swings
to the high pressure side.
lWhen oil pressure is low, the internal contactsof the gauge unit open in a shorter period of
time. Therefore, there is less current flowing
in the circuit and the gauge pointer swings to
the low pressure side.

lWhen the ignition key is set to the “ON” position,the gauge indicator will be at
“0”.l
When the engine is started, the indicator will
move from
“0” to the minus (-) side, and then,as the boost level increases, it will move to
the plus
(+) side.
l When the ignition key is placed in the “ON”
position, the voltage gauge operates and indi-
cates a battery voltage of approximately 12 V.l
When the engine is started, the voltage gauge
indicates a battery voltage of 12 to 16 V, indicat-ing that the battery is on charge.
4. The oil pressure gauge doesn’t function, or
shows the incorrect indication.
(1)The “H” side is indicated when the connectorof the oil pressure gauge unit is discon-
nected and then grounded.l Check the oil pressure gauge unit.
5.The meter illumination light does not illuminate.
(1) The tail lights illuminate.l Check the rheostat.
6. The voltage gauge doesn’t function, or shows
the incorrect indication.l Check the voltage gauge.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System54-39
ZOMPONENT LOCATION
Headlight relay/Pop-up motor relay/
HeadliiW,$w, q\\ u,6F026,
Data link connector

\V16FO49E
Light automatic shut-off unit

-Light automatic shut-off unit

i
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-54CHASSIS ELECTRICAL - Lighting System
CIRCUIT DIAGRAM (CONTINUED)
IGNITIONSWITCH(ACC)I
2L2W-B
5W-BHORN
(c-82) ,P/x1=
J/Ba315A10A
IOD ORSTORAGE
CONNECTOR
L
AUTOMATIC
SHUT-OFF
L";@v;$TE UNITE
LYY-BR-E
(F>R-E
R-Br
DOME LIGHT,FOOT LIGHT
AND IGNITION
KEY CYLINDER
ILLUMINATION
LIGHT
51---------7
(F)R-B
2B
DOOR LIGHT
AND LUGGAGE
EWtRTMENT
d,
3NNECTOR
3I3HROBM03BA
1 TSB RevisionI

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
COMPONENT LOCATION
54-63
Headlight relay / Foglight relay
Light automatic shut-off unitLight automatic shut-off unit
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine i;CHASSIS ELECTRICAL
- Lighting System54-71
COMPONENT LOCATlON
.Light automatic shut-off unit
:Vehicles withkeyless entry system>
Light automatic shut-off unit
:Vehicles without keyless entry system>
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-72CHASSIS ELECTRICAL - Lighting System
DOME LIGHT, FOOT LIGHT AND IGNITION KEY CYLINDER ILLUMINATION LIGHT
CIRCUIT DIAGRAM (UP TO
1993 MODELS)
FUSIBLE LINK@IGNITIONSWITCH(IGl)
5W-B,.l (c-68)2B-w,,7m/\\J/B
@0310A
L
(c-74)
R-B
I
IO"3 (c-80)
B-W
jl52;gF"___-_________ _----__--_-_--, IOD OR
STORAGE
CONNECTOR
(A-11X)
(c-83)
R-B
R-E
DOME
LIGHT
:E-05)(
R-G
I1(c-81)
0.85R-I
R-E
(LH) (RH:Z-67
-
R-c
$
KEY CYLINDERILLUMINATION
//
,
III
I
1IIIIIII
I
bIOOR
(c-74)
J/B r
(c-83))ICONNECTOR0------- -----
1
R-GIR-G2Ej
27
m(c-34)(c-58)(RH)(LH)\InY
DOOR SWITCH
d
R-G
R-G
d,HR08MlOAA
/ TSB Revision