1993 GMC SIERRA coolant temperature

How To Use This Manual
These symbols are used on warning lights in your vehicle:
1-
Engine Coolant Temperature
BRAKE
Brake Battery
Charging
System
I RELEASE
Parking Brake Release
s Fuel
SHIFT
Shift Light
Engine Oil
Pressure
Low
Coolant
Here are some other symbols you may see:
Fuse
I II
Hood Release Lighter Horn
PO594
0-6
ProCarManuals.com

When your engine is cold, let it run for a few minutes before you move your
vehicle. This lets oil pressure build up. Your engine will sound louder when
it's cold.
NOTIP
-
If you're not in an idling vehicle and the engine overheats, you wouldn't
there to see the coolant temperature gage. This could damage your
hicle. Don't let vour enaine run when you're not
in vour vehicle.
Cold Weather Starting (Diesel Engine)
The following tips will help you get good starting in cold weather.
Use
SAE IOW-30 oil when the outside temperature drops below freezing.
When the outside temperature drops below
0°F (-18"C), use your engine
block heater.
If you park your vehicle in a garage, you shouldn't need to use \
the block
heater until the garage temperature goes below
0°F (-18"C), no matter how
cold it is outside.
To use the engine block heater, first turn
off the engine. Then open the hood,
unwrap the electrical cord and plug it in. It uses normal house voltage
(110
volts), but:
2-1 7
ProCarManuals.com

Features & Controls
Listed are four situations you may experience with your fuel g\
age:
At the gas station, the fuel pump shuts off before the gage reads full.
It takes a little more or less fuel to fill up than the fuel gage indicated.
For example, the gage may have indicated the tank was half fu\
ll, but
it
actually took a little more or less than half the tank's capa\
city to fill the
tank.
The gage moves a little when you turn a corner or speed up. \
The gage doesn't go back to empty when you turn off the ignition.
None of these indicate a problem with the fuel gage.
For information on how to
fill your fuel tank see "Fuel-Filling Your Tank" in
the Index.
For your fuel tank capacity, see "Fuel-Tank Capacity"
in the Index.
Engine Coolant Temperature Gage
760
K2334
This gage shows the engine coolant temperature. If the gage pointer moves
into the red area, about 260°F
(145°C) or more, your engine is too hot! It
means that your engine coolant has overheated.
If you have been operating
your vehicle under normal operating conditions, you should pull \
off the road,
stop your vehicle and turn
off the engine as soon as possible.
Hot Coolant Can Burn You Badly!
In "Problems on the Road", this manual shows what to do. See \
"Engine
Overheating" in the Index.
2-88
ProCarManuals.com

Heater Output
Optional Engine Block Heater
If your engine is equipped with an optional engine block heater, you can use
it during initial start-up in cold weather (20”F,
-8”C, or lower) to help heat the
passenger compartment faster. Because an engine block heater war\
ms the
engine coolant, your vehicle’s heating system can provide som\
e heat as soon
as you start the engine.
The use
of an engine block heater also reduces the time it takes for the
engine to reach normal operating temperature, and shortens the time it takes
the heater to reach full output. For more information, See “Engine Block
Heater” in the Index.
Diesel Engine
If you idle your diesel engine for a long time when it’s cold\
outside, your
heater may blow out cool air. This is normal. When you increase the \
engine
speed, your heater should blow out warmer air.
If it doesn’t, your coolant
level may be
low. See “Engine Coolant’’ in the Index to find out how to
check your coolant level.
Electronic HeatingAir Conditioning System
Function Display
K2305
If your vehicle has air conditioning, your heating/air conditioning \
system will
look like this.
3-5
ProCarManuals.com

If your vehicle has the four-wheel-drive option and the transfer c\
ase is
engaged, a dolly must be used under the rear wheels when towi\
ng from the
front.
Engine Overheating
You will find a coolant temperature gage on your vehicle instrument\
panel. If
you have a diesel engine, you will also find a low coolant light on your
instrument panel.
If Steam Is Coming From Your Engine:
K2509
I CAUTION
A
Steam from an overheated engine can burn you badly, even if you
just open the hood. Stay away from the engine
if you see or hear
steam coming from it. Just turn
it off and get everyone away from
the vehicle until
it cools down. Wait until there is no sign of steam
or coolant before opening the hood.
If you keep driving when your engine is overheated, the liquids in it
can catch fire. You or others could be badly burned. Stop your
engine
if it overheats, and get out of the vehicle until the engine is
cool.
5-9
ProCarManuals.com

Service & Appearance ,Care
Engine Coolant
r
PO593
The following explains your cooling system and how to add cool\
ant when it is low.
If you have a problem with -engine overheating, see “Engine
Overheating” in the Index.
The proper coolant for your vehicle will:
Give freezing protection down to -34°F (-37°C).
Give boiling protection up to 258°F (125°C).
Protect against rust and corrosion:
Help keep the proper engine temperature.
Let the warning lights and gages work as thiy should.
What to Use:
Use a ,mixture of clean water (preferably distilled), and antifreeze that meets
“GM Specification 6038-M,” which won’t damage aluminum p\
arts.
Also use
GM Engine Coolant Supplement (sealer) with a complete coolant change. If
you use these, you don’t need to add anything else.
,
6-42
ProCarManuals.com

Service & Appearance Cam
Thermostat
Engine coolant temperature is controlled by a thermostat in the engine coolant
system. The thermostat stops the flow of coolant through the r\
adiator until the
coolant reaches a preset temperature.
When you replace your thermostat, an
AC@ thermostat is recommended.
Power Steering Fluid
K2630
How To Check Power Steering Fluid:
Unscrew the cap and wipe the dipstick with a clean rag. Replace the cap
and completely tighten it. Then remove the cap again and look at the fluid
level on the dipstick.
K2693
6-46
ProCarManuals.com

Scheduled Maintenance Services
Explanation Of Scheduled Maintenance Services
Below are explanations of the services listed in the maintenance charts.
The proper fluids and lubricants to use are listed in this section. Make sure
whoever services your vehicle uses these. All parts should be \
replaced and
all necessary repairs done before you or anyone else drives the ve\
hicle.
1.
ENGINE OIL AND OIL FILTER CHANGE* -ALWAYS USE SG OR
SGKE QUALITY, ENERGY CONSERVING II OILS OF THE PROPER
VISCOSITY. To determine the preferred viscosity oil for your vehicle’s
engine (e.g. SAE 5W-30 or 10W-30), see “Engine Oil” in the Index.
2. CHASSIS LUBRICATION -Lubricate the front suspension, king pin
bushings, steering linkage, transmission, and transfer case shift\
linkage,
parking brake cable guides, propshaft splines (2 wheel drive), brake
pedal springs, and clutch pedal springs at the intervals specified.
If you have a 3500 HD, lubricate the king pins and king pin bushings
every 1,500 miles
(2500 km) for Maintenance Schedule 1, or every 3,000
(5000 km) for Maintenance Schedule 2.
Ball joints and king pin bushings should not be lubricated unless their
temperature is
10°F (-12”C), or higher. When the weather is cold, let
them warm up before lubrication or they could be damaged.
Also, be sure to check
all the vehicle fluid levels at this time.
3.
CLUTCH FORK BALL STUD LUBRICATION -Lubricate the clutch fork
ball stud through the fitting on the clutch housing. Lubricant must be
added “sparingly” to the fitting, as only.
0066 Ib. (.003 kg) is required to
lubricate the ball stud surface.
Do not add lubricant more often than the
intervals in the Maintenance Charts.
Too much lubricant will damage
the clutch assembly.
4. ENGINE IDLE SPEED ADJUSTMENT (DIESEL ENGINES)* -Adjust to
the specifications shown on the underhood label. You must use
calibrated test equipment.
5. COOLING SYSTEM SERVICE* -Drain, flush and refill system with new
coolant. See “Engine Coolant’’ in the Index for the proper coolant and
mixture to use in your vehicle.
Also inspect the hoses and replace them
if they are cracked, swollen, or
deteriorated. Tighten all hose clamps (except constant tension \
clamps).
Remove debris and clean the outside
of the radiator and air conditioning
condenser. Wash the radiator neck.
To ensure proper operation, pressure
test the radiator and cap.
* An Emission Control Service
7-1
8
ProCarManuals.com