1993 FORD SIERRA wiring

pA Front Caliper We offer high quality re-manufactured
front calipers which are considerably less costly than new.
Calipers are handed left & right and require return core charge.
(drivers- left) M420CL(passenger- right) M420CR
pB
Caliper Repair Kit -w/piston Ford caliper repair kits are
an economical way to service a leaking or "sticky" caliper. Fitting
this kit, after honing the piston bore, will cure most caliper related
problems. (kit does 1 caliper)M420K4A
pC
Caliper Seal Kit After inspection many calipers only
require new seals to put them right. (kit does 1 caliper) M420K4
pD
Performance Street Brake Pad Set Premium
Mintex A/F series brake pads will give enhanced brake perform
over a wide temperature range with very little brake dusting.
Mintex pads also incorporate the pad warning sensor wiring.
This is the abusolute best performing street pad we have tested
and for the price they are a steal.
(XR4 & Scorpio)M420M
pD
Racing Brake Pad Sets Mintex 1144 is a rally/race pad
that is perfectly at home on track or street, offering a high coefficient
of drag (.44) and excellent modulation throughout a very wide
operating range (up to 1200 degrees). Mintex 1144 is supplied pre-
burnished for easy break-in and minimal fade on the first heating
cycle. Both fade resistance and wear characteristics are excellent.
Mintex pads are the only racing brake pads to incorporate the
standard "low pad" sensor wiring. Match a set of these pads with our
drilled or grooved sport rotors and Aeroquip stainless brake lines for
a substantial increase in braking performance.
(XR4 & Scorpio)
Mintex Street/Competition (M1144)M420G
Mintex Full Competition (M1155) M420GA
pE Standard Front Rotors Lesser quality generic "white
box" rotors tend to warp easily, don't even consider fitting them
on your XR4 or Scorpio. BAT supplies only the highest quality
(Brembo -
Italy & United Brake -England) rotors at better than
"bargain" rotor prices. (each)
XR4 M425
Scorpio G425
pE
pC
pD
pD
pA
pB pF
Brake System (front)
pH
See price list for caliper
slide bushings and pins
pG
0 7
check price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items
pF Cross Drilled Front Rotors Cross-drilling brake
rotors is an excellent way to increase brake performance.
Theory being that centrifugal force will draw excess brake
dust and expelled gasses from the pad surface through the
drilled passages into the rotors vented cavity and out. This
process also improves rotor cooling giving improved braking
response and resistance to fade. Our drilled brake rotors
are made from Carballoy (a medium flake graphite fully
pearlitic low phosphorous iron) manufactured to BS 1452
- 1990 grade 180/220 standard. The cross drilling process
is handled by computer CNC milling equipment with holes
arranged in a parabolic pattern giving an even sweeping
effect to the pad surface ensuring maximum cooling with
minimum noise and drag. M425CD
*rotors must by purchased as (handed) pairs- priced as each
Grooved Front Rotors As an option we can supply
slotted (grooved) pattern rotors which are manufactured to
the same high standards as the above listed cross drilled
versions.M425S
*rotors must by purchased as (handed) pairs- priced as each
Drilled & Slotted Front Rotors As an option we can
supply combination drilled & slotted (grooved) pattern
r o t o r s manufactured to the same high standards as the above
listed cross drilled versions.M425CDS
*rotors must by purchased as (handed) pairs- priced as each
pG Master Cylinder high quality Bendix replacement power
brake master cylinder.
(specify year when ordering)M420MC
pH
Aeroquip Brake Lines One of the more effective brake
modifications you can make is to replace the standard brake
hoses with Aeroquip steel braided lines. These performance
brake hoses incorporate a teflon interior to keep line expansion
"flexing" to a minimum. This greatly reduces the "spongy" pedal
feel common to the XR4 & Scorpio brake system. Our stainless
lines are assembled from genuine Aeroquip AN-3 hose with
premium metric "reusable" (not the lesser quality "swaged" type)
hose ends installed. XR4Ti (state year) M419
Scorpio G419

Bodywork
pL
pM
pNpE
pA pL
pC pD
pF
pBpG
pH
pI
pJ
pK
pA Front Fenders European Sierra fenders are a direct replacement for the
XR4Ti and are an attractive alternative considering the high price of the American
version. These fenders also include the holes required for side blinker mounting
(see below).
Note: specify left or right when ordering M806 L/R
pB
Inner Wheel Well Splash/Liners Replacements for the commonly
cracked, broken or missing inner fender splash on the XR4. Covers full inner
wheel house area as origional USA versions.
specify left or right M808L/R
pC
Door Skin - (specify left or right)M807 L/R
pD
Door Handle XR4 & Scorpio - (specify left or right)M362 L/R
pE
Door Sill (Rocker Panel) - (specify left or right)M803 L/R
pF
Rear Wheel Arch - (specify left or right)M804 L/R
pG
Battery TrayM817
pH
Rear PanelM815
pI
Cosworth Front Grille Nothing transforms the look of the XR4Ti quite like
adding a Cosworth grille. Designed with a center opening, the Cosworth grille
adds additional air flow to the radiator and A/C condenser for a cooler running
engine and better air conditioning performance. An intercooler could also be fitted
behind the grille opening as is done on the original Cosworth Sierra and R/S 500
models.
Note: Grilles are O.E. quality (injection moulded plastic) not shoddy fiberglass
replicas. Suppled (primed) un-painted- includes "Ford" emblem
M320
pJ
Grille Surround Gasket This gasket will almost always need to be
replaced when fitting a new grille.M320S
pK
European Side Blinker Lamp Kit Add an extra degree of safety when
signaling to turn. Side blinkers fit above European fenders without modification
and can also be fitted to standard Merkur XR4Ti fenders by drilling a mounting
hole. Kit includes (2) lamps, wiring and templates.M317
pL
Cosworth Hood Original equipment Ford Sierra Cosworth hoods are
designed to receive hood vents/louvers for additional under hood cooling. These
hoods look quite distinctive as the raised center section is lower and wider than
on the standard XR4 hood giving the car a more aggressive appearance.M813
pM
Cosworth Hood Vents Hood louvers/vents are both visually striking and
functional as they help to ventilate the engine compartment. These O.E. Ford vents
(pair) bolt into the Cosworth hood (above) or can be fitted to standard hoods by cutting
a hole and bonding them in place.
(see pg 11 for fiberglass versions)M814
pN
Cosworth Front Spoiler/Bumper We supply everything required to
install the stunningly attractive Cosworth Sierra front spoiler/bumper to your
XR4Ti. All components are original Ford including; bumper, bumper bar
brackets, lower side fender mounting panels, fog lamps, turn signal lamps, and
assorted hardware (clips & fasteners).
Note: bumpers are supplied in white-
can be painted to match other colors.
M353
(R/S 500 Version) M353RS
1 2

Trim & Lighting
pA European Emblems & Badges Re-badge your XR4 with Ford ovals
and Sierra emblems or put the finishing touches on that Cosworth clone.
Genuine Ford European logos will distinguish your XR4 or Scorpio from the
rest. Location (on car) for emblems and sticker logos are listed below.
Emblems are chrome and black plastic with self stick backing. Stickers can be
applied to metal or glass surfaces.
Sierra (emblem)
rear hatch leftM321S
Sierra XR4i Red (sticker)
rear hatch leftM352R
Sierra XR4i Anthracite/Gray (sticker)
rear hatch leftM352A
Sierra R/S (emblem)
rear hatch leftM321RS
Cosworth (emblem)
rear hatch left under Sierra R/S emblemM321C
Sierra R/S Cosworth (sticker)
rear hatch leftM352C
R/S (emblem)
side fender XR & ScorpioM352RS
Ghia- crest (emblem)
side fender XR & ScoprioM352G
Oval "Ford" (emblem)
front grille center & rear hatch rightC321
"Ghia"- script (emblem) Scorpio rear hatchG352G
2.9i (emblem)
Scorpio rear hatchG352L
Scorpio (emblem)
Scorpio rear door sail panelG352S
pB
European Headlamps The standard US spec. XR4 & Scorpio
headlights were pretty poor when new, and get worse with age- especially when
the lenses turn cloudy. European headlamps will provide a significant increase
in light output and they look great too. These lamps utilize all glass lensing with
a halogen H-4 55/60 watt bulb for high/low main beam operation, and a halogen
H-3 55 watt bulb for the built-in driving lamp.
Note: Lamps are supplied in right hand
drive (English) specification which has a subtle different low beam flair pattern,
however, this is not very noticeable. If required left hand (German) type lenses are
available separately (see price list). We recommend installing the lamps first before
opting to swap out the lenses as most customers do not bother.
Sierra XR4 European Headlamp Kit* M318
*kit includes (2) lamps, rear bulk heads panels, bulbs & wiring instructions
Scorpio* European Headlamp Kit G318
*kit includes (2) lamps, left & right lamp lamps/indicators & front grille sections,
bulbs, and wiring instructions
Scorpio Fog Lamp (LH)- complete replacement assembly G349L
Scorpio Fog Lamp (RH)- complete replacement assembly G349R
pC
Head Lamp Bulbs Replacement and higher wattage bulbs for above
European headlamps and standard XR4 & Scorpio aerolamps. Headlamps- H4
bulbs are fit eurolamps (not stock headlamps), 9004 bulbs are for use with standard
XR4Ti & Scorpio aerolamps. Fog lamps- H3 bulbs are suitable for eurolamps and
Scorpio, 880 bulbs fit
only XR4Ti fogs. Krypton gas 9004 "Bright White" bulbs burn
brighter with more luminous output than standard halogen type bulbs.
"Blue Ion"
bulbs project a, low glare, blue tinted beam- definitely a different look !
H4 55/60 watt (for high/low main beam) Z H4 55/60
H4 55/100 watt (for high/low main beam) Z H4 55/100
H4 80/100 watt (for high/low main beam) Z H4 80/100
H3 55 watt (for fog & driving lamps) Z H3 55
H3 100 watt (for fog & driving lamps) Z H3 100
880 50 watt "Blue Ion" 50 watt (for XR4Ti fog lamps) Z 880/50B
880 50 watt "Amber" 50 watt (for XR4Ti fog lamps) Z 893/50G
9004 "Bright White" 45/65 watt (for high/low main beam) Z 9-45/65W
9004 55/100 watt (for high/low main beam) Z 9-55/100
9004 80/100 watt (for high/low main beam) Z 9-80/100
9004 "Blue Ion" 55/100 watt (for high/low main beam) Z 9-55/100B
Relay (Hella) 12 volt-
(2) required w/ 80/100 bulbsZ Relay12
pD
Rear Tail Lamp Seals & Lamp Sockets Puddles in the trunk or damp
carpeting might be due to leaking rear tail lamp seals. Non-functioning tail
lamps are usually due to corroded lamp sockets. We have new replacements
for both these USA Ford unavailable parts.
Left or Right Tail Lamp
Seal- XR4 M319S
Left or Right Tail Lamp
Socket- XR4 M319LS
H4 H3 9004 pC
pD
pA
(h XR) (Scorpio i)
pB
Scorpio fog lamps
1 4

pA
pB
pC
pD
pE
pF
pG
pH pJ
pK
pL
pP
pIpN
pOpM
pS
pR pQ
Cooling System (Scorpio)
In addition to our stock of cooling system components for the XR4Ti
we have added the various Scorpio related items to our inventory.
The Scorpio's cooling system is only slightly less complicated than
the XR4Ti's, it's only saving grace is the parts do not vary all that
much from year to year. Again, as with the XR4, components that
we offer are from the O.E. supplier or Ford originals.
pA Hose*- heater valve (outlet) to heater core G421HA
pB
Hose*- heater valve to engine/inlet mfld.G421HB
pC
Hose*- heater valve (inlet) to heater coreG421HC
pD
Hose*- heater valve to pipeG421HD
*for additional info see (diagram A) on page 20
pE Radiator- new original equipment Ford radiators at a very
attractive prices. Don't be mislead into buying substandard
fabricated or fits-all radiators when we can supply new Ford ones
for less.
(for automatic trans)G421RA
(for manual trans.)G421R
pF
Hose- coolant tank to thermostat housingG421HF
pG
Hose- top radiator hose (88-89)G421TH
pG
Hose*- top radiator hose (89 late) has vent air bleed in line
(includes bleed screw).G421TH-9
*for additional info see (diagram B) on page 20
pH Hose- tank (lower) to water pumpG421HH
pI
Water Pump- new Ford water pumpG421
pI
Water Pump- high quality reconditioned water pump on
Ford core.G421A
Hose*- bypass from water pump to inlet mfld.G421HP
*for additional info see (diagram A) on page 20
pJ Hose- lower radiator hose 88-89G421BH
pJ
Hose*- lower radiator hose (89 late) has additional tee off
hose running to overflow tank @ lower bungG421BH-9
*for additional info see (diagram B) on page 20
pK Hose*- to oil cooler pipeG421HK
pL
Hose*- oil cooler pipe to oil coolerG421HL
*for additional info see (diagram A) on page 20
pM Coolant Tank- Cracked and leaking overflow tanks are a
common problem on the Scorpio. Tank pictured above is for early
(1988) type cars.
See page 20 for late style tanks.G421TE
pN
Radiator Cap- cap for Scorpio and XR4's with thread-on
coolant tankG421C
pO
Oil Cooler- replacement water to oil heat exchanger.
If water is showing up in your oil it would most likely be either a head
gasket or one of these.AD1000
pP Heater Control Valve- heater control valve, same on
XR4 & ScorpioM421V
pQ
Heater Core- Quality Ford O.E. heater cores.G471
pR
Mechanical Fan Clutch- Quality Ford O.E.G422
pR
Electric Fan- An altermative to the Scorpio mechanical
clutch fan. This highly efficent (1150 cfm) 16" electric "puller" fan
moves more air and frees up a few HP to boot. Wire directly or use
our (optional) adjustable 165-215 degree thermostat/relay wiring kit.
(16" electric fan) A16F-PL
(thermo/relay wiring kit) AFTR1
pS
Heater A/C Blower Motor- New Ford heater blower motor
for Scorpio with 8 wire harness/plug.
G470H
see (diagram A) on page 20
2 2

Engine & Related Items
2.5mm metallic inductance EMI
suppressed conductor: with
stainless steel windings spaced
over ferrimagnetic core
substrate
serves as
strength
member for
cable assembly
ignition cables have a non-layered high strenght insulating
jacket made entirely of aerospace grade silicone rubber to
prevent swelling and splitting at extreme trmperatures
KV85 & R-100
metallic inductance EMI
suppressed conductor
pA Performance Air Filters A quick and easy performance modification
is to replace the standard air filter with a direct fit KN high performance air filter.
Merkur XR4Ti (2.3L Turbo)M22P
Merkur Scorpio (2.9L V-6)G22P
pB
High Temp Fyre Sleeve The under hood temperatures on the XR4Ti can
be quite severe. Slipping a length of fyre sleeve over critical wiring or rubber water
& A/C hoses will add an extra degree of protection. Fyre Sleeve provides radiant heat
protection up to 800 degrees. Sleeve is sold per foot and is sized by internal diameter.
Hoses or wiring can be disconnected at one or both ends then slipped through fyre
sleeve or sleeve can be un-stitched at the seam and wire tied in place.
Mylar Fyre Foil Sleeve -10 (7/8" I.D.) per foot320510
Mylar Fyre Foil Sleeve -12 (1" I.D.) per foot320512
Mylar Fyre Foil Sleeve -16 (1 1/4" I.D.) per foot320516
Mylar Fyre Foil Sleeve -20 (1 1/2" I.D.) per foot320520
pC
Engine Mount Insulators BAT has an alternative to the recently
discontinued original equipment Ford motor mounts on the XR4Ti. Simply
remove the old motor mount assemblies, discard the worn-out rubber
portion, and reuse the top and bottom metal plates with our replacement
insulators.
Note: slight modification requires 10mm holes in plates to be
increased to 12mm. Scorpio mounts are Ford mfg. direct replacements.
Engine Mount Insulator (left & right same) XR4TiM433
Engine Mount Insulator (left & right same) Scorpio-
new FordG433
pD
Transmission Mount /Insulator Rear transmission mount/insulator-
direct fit for automatic & manual Scorpio. A heavy duty version also available.
Note:
this "square" type mount can be fitted to the XR4 with special crossmember, (see
below) as the standard "round" trans. mount used on our XR4Ti's is no longer available.
Transmission Mount Insulator*- (automatic & manual) G433T
Transmission Mount Insulator H.D*.- (automatic & manual) M433TA
*can be fitted to XR4 with additional x-member (see below)
pE Transmission Crossmember Wide and narrow type transmission
tunnel crossmenbers allow the above "square" mount/insulators to be installed in
the XR4Ti. Fitting the XR with this crossmember/mount combination is a consider-
able upgrade (strength, noise, vibration) over the USA supplied "round" mount.
Crossmember* XR4 (wide) 1987-89- manual & auto M433XL
Crossmember* XR4 (narrow) 1985-86- manual & autoM433X
*for use in combination with above G433, M433 "square" type mount
pF Engine Belts H.D. Our search for the ultimate heavy duty engine
accessory v-belts lead us to the top cog "Gold Series" by Dayco. Top cog v-
belts are built to last up to 20% longer than conventional belts. A unique cogged
design increases flexibility and airflow around the belt for reduced friction and
heat. Laminated design with high temperature rated polyester cords provide
maximum tension holding (reduced slip) over the life of the belt.
Belt- XR4Ti (1985-89) W. Pump, Alt, P. Steering (2 required)M6G
Belt- XR4Ti (1986-89) A/C CompressorM6H
Belt- XR4Ti (1985) A/C CompressorM6HA
Belt- Scorpio (1988-89) Fan & Power Steering (2 required)G6G
Belt- Scorpio (1988-89) AlternatorG6GA
Belt- Scorpio (1988-89) A/C CompressorG6H
pG
Performance Ignition Wire Sets We have tried a number of
different ignition wire options on the 2.3 Turbo and 2.9L V6 engines and have
found the Magnecor brand to offer superior quality, performance, and durability.
Cables are red in color with 8mm, 8.5mm and 10mm cable diameters.
Merkur XR4Ti (2.3L Turbo)
Ignition Wire Set- (8mm w/silicone jacket and boots)L9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)M9HT
Ignition Wire Set- (10mm R-100 wire w/silicone jacket and boots)M9HTR
Merkur Scorpio (2.9L V6)
Ignition Wire Set- (8mm w/silicone jacket and boots)G9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)G9HT9 pG
pF
pA
Aluminized Mylar Fyre Sleeve
pB
pC pD
pE
2 7

Engine & Related Components
pADistributor Cap 2.3L Heavy duty epoxy/resin cap
w/brass terminals.L9B

pBDistributor Rotor 2.3L Heavy duty epoxy/resin rotor
(screw down type 1985-86).
L9F
pB
Distributor Rotor 2.3L Heavy duty epoxy/resin rotor
(push- on type 1987-89).
L9FA
pC
TFI Module 2.3L (Motorcraft)L9M
pD
Distributor 2.3L excludes cap, rotor, module
(35.00 core)
re manufacturedL9AB
pD
Distributor 2.9L excludes cap, rotor, module
(55.00 core)
remanufacturedG9AB
pE
Engine Management XR4Ti and Scorpio engine
management computers. (75.00 core)
remanufactured
XR4TI (specify auto or manual trans) M9C
Scorpio (specify auto or manual trans) G9C
2.3L Turbo Engine Sensors & Switches
pFElectric Fan Switch -XR M450FS
pGKnock Sensor-XR M450KS
pHEngine Coolant Temp Sensor (ECT)-XR M450EC
pIIdle Speed (Air Bypass Valve) XR/Scorpio
M450IS
pJThrottle Position Sensor (TPS)-XR M450TP
pKOxygen Sensor (OS)-XR M450OS
pLOil Pressure Switch-XR M450P
pM
Water Temp Gauge Sender- XR (purple band)M450F
Sensors & Switches (other)
Air Charge Temp. Sensor (ACT) Scorpio G450A
Coolant Temp. Sensor (ECT)- Scorpio M450EC
MAP Sensor -Scorpio G450M
Oil Pressure Switch- Scorpio G450P
Oxygen Sensor- Scorpio G450OS
Vehicle Speed Sensor- Scorpio G450S
Throttle Position Sensor- Scorpio G450TP
pCpB pA
pD
pN
pE
pNA/C Compressor XR4/Scorpio Nippondenso A/C
compressor units, includes clutch.
remanufacturedM470C
pO
Alternator Bosch (90 amp) alternators available for XR &
Scorpio. (10.00 core)
remanufactured.
Alternator -XR4TiM24A
Alternator -ScorpioG24A
pPStarter XR4Ti and Scorpio starter units. (30.00 core) re
manufactured.
Starter -XR4TiM23A
Starter -ScorpioG23A
pQFuel Injectors Replacement injectors for XR4Ti.
35 lb. Standard Brown Top Injector (reman) M7G
35 lb. Optional Disk Type Injector (new) L7G
pRVane Air Meter Larger 50mm (T-bird) and 65mm (SVO)
VAM's can be fitted as a performance upgrade on the XR4Ti.
("PE"
computer chip upgrade required)
50mm VAM (reman) L7V
65mm VAM (reman)L7VA
Standard VAM XR4Ti (reman)L7VM
pSFuel Pressure Regulator Standard replacement regulator
for XR4Ti.M7PR
pTElectric Fuel Pumps New XR4Ti (in line) high pressure
and (in tank) low pressure fuel pumps
Electric Fuel Pump (in line) high pressureM10A
Electric Fuel Pump (in tank) low pressureM10AT
Important note: all electrical items are pre-
tested before shipping. Carefully check all
wiring, fuses & relays
before ordering. Electrical
items are not returnable !
pF pGpHpI
pJ
pK
pL
pM
pO
pQpP
pS
pT
pR
3 1

07/30/02Price List3 6
PAGE 10 driveline components
C.V. Joint- XR & Scorpio M550B 92.50
C.V. Boot Kit- XR & Scorpio M550BK 14.90
C.V. Socket Head Cap Screw (6 per joint) M550CS 1.05ea
C.V. Locking Plate (3 per joint) M550LP 1.35ea
Axle/Halfshaft Complete* (LH)- XR & Scorpio M550L 169.50
Axle/Halfshaft Complete* (RH)- XR & Scorpio M550R 169.50
*axle/halfshaft, joints (2), boots (2), assembled/greased ready for installation
add 75.00 core charge for this item- refundable on return
Driveshaft Coupling- XR & Scorpio M17A 62.50
Drivesahft Center Support Bearing-XR M550SB 109.75
Drivesahft Center Support Bearing- Scorpio G550SB 98.00
Quaife LSD M710 1245.00
Clutch Kit Sachs- XR M519K 179.50
Clutch Kit Sachs- Scorpio G519K 257.50
Clutch Kit Sachs- XR w/ T-5 trans M519T5 179.50
H.D. Clutch Kit Centerforce (30% kit) M519C 309.95
H.D. Clutch Kit Centerforce II (50% kit) M519C2 361.98
Clutch Alignment Tool (1" 23 spline) S11H 6.00
Clutch Cable- XR4Ti M562 29.50
Clutch Cable- Scorpio G562 76.50
BAT is always testing and
developing new products....if
you don't see it listed ask... we
might have what you are looking
for, or can point you in the right
direction.
PAGE 8 brake kits & specials
Front Brake Spacial- XRM420SP 105.00
Front Brake Spacial- ScorpioG420SP 115.00
Front R/S Brake Kit 283x24mm (standard) M417 295.00
Front R/S Brake Kit 283x24mm (w/x-drill) M417A 329.00
Front R/S Brake Kit 283x24mm (standard/M1144 ) M418 339.00
Front R/S Brake Kit 283x24mm M1144/x-drill) M418A 395.00
BAT/Wilwood Brake Kit 283mm M416W 645.00
BAT/Wilwood Brake Kit 300mm M416W3 725.00
PAGE 9
rear brake components
Rear Wheel Cylinder- XRM420WC 35.95
Rear Brake Shoe Set (Motorcraft/Mintex)- XRM420R 49.95
Rear Brake Drum
- XRM420RD 74.00
Rear Brake Drum (grooved)
- XRM420RDG 129.50Aeroquip Rear Brake Lines (pair)- XRM419R 47.50
Rear Brake Line O.E. Rubber (each)- XR4 (1985-89)M419SR 27.45
Aeroquip Rear Brake Lines (4 line set)- ScorpioG419R 85.00Rear Brake Hardware Kit- XR M420K5 25.60
Rear Brake Special- XR M420RSPL 125.00
Rear Disk Brake Kit- XR M420RK 689.00
Hand Brake Cable- XR M564 44.00
Handbrake Cable- Scorpio G564 44.00
Hand Brake Cable- Cosworth Z16567 44.00
Rear Caliper* (specify left or right) for M420RK kit127.50
*this item requires an additional 75.00 core charge refundable upon core return
Rear Rotor (each) for M420RK kit52.50
Rear Brake Pad (set) for M420RK kit25.00
Rear Rotor (standard)- Scorpio (each)G425R 39.75
Rear Rotor (x-drilled)- Scorpio (each)G425RCD 92.00Rear Caliper (left)- Scorpio (each)G420RL 124.50
Rear Caliper (right)- Scorpio (each)G420RR 124.50
*this item requires an additional 75.00 core charge refundable upon core returnRear Brake Pad Set- Scorpio (Semi-Metalic)G420R 39.00
ABS Brake Sensor Scorpio/XR4- Rear G420SR 177.25
PAGE 7 front brake components
Front Caliper* (left)- XR & Scorpio M420CL 64.75
Front Caliper* (right)- XR & Scorpio M420CR 64.75
M420CL/CR calipers are not supplied with slide pins or bushings (available below)
Front Caliper Complete* (LH) includes mount & pads M420CL-L 90.00
Front Caliper Complete* (RH) includes mount & pads M420CL-R 90.00
*this item requires an additional 75.00 charge refundable upon core return
Caliper Repair Kit- XR & ScorpioM420K4A 55.00
Caliper Seal Kit-
XR & ScorpioM420K4 17.75
Caliper Slide Bushings (2) does 1 caliper M420CB 14.00
Caliper Slide Pins (2) does 1 caliper M420CP 16.35
Caliper Spring (anti-rattle) each M420CS 6.39
Front Brake Pad Set*- Mintex A/F (Semi-Metalic) M420MM 39.00
Front Brake Pad Set*- Mintex 1144 (street/competition) M420G 75.00
Front Brake Pad Set*- Mintex 1155 (full competition) M420G 112.30
*brake pads will fit both XR4 and Scorpio
Front "Low Pad" Sensor Wiring Harness- XR/Scorpio M420WS 32.49
Front Rotor (standard)- XR (each)M425 42.50
Front Rotor (standard)- Scorpio (each) G425 49.75
Front Rotor (x-drilled)- XR (each)M425CD 79.50
Front Rotor (x-drilled)- Scorpio (each) G425CD 99.00
Front Rotor (x-drilled & slotted combo)- XR (each)M425CDS 89.50
Front Rotor (x-drilled & slotted combo)- Scorpio (each)G425CDS 109.00
Master Cylinder* XR4 1985-86 (Bendix)- XRM420MC 109.50
*this item requires an additional 20.00 charge refundable upon core return
Master Cylinder* XR4 1987-89 (Bendix)- XRM420MCL 122.50
*this item requires an additional 50.00 charge refundable upon core return
Aeroquip Front Brake Lines (pair)- XR4 (1985-88)M419 42.50
Front Brake Line O.E. Rubber (each)- XR4 (1985-86)M419SF 25.75
Aeroquip Front Brake Lines (pair)- XR4 (1987-89)G419 52.40
Aeroquip Front Brake Lines (pair)- ScorpioG419 52.40
ABS Brake Sensor Scorpio/XR4- Front G420SF 179.75
PAGE 11 brake components
Brake Fluid AP550 (500 ml) MC550 10.70
Brake Fluid Wilwood 570 (355 ml) MC570 5.95
Brake Fluid Wilwood 570 (6-pack) MC57-6 33.00
Brake Fluid Wilwood 570 (24 case) MC57-C 119.00
Front Rotor Cosworth 283 x 24mm (standard) M426 75.00
Front Rotor Cosworth 283 x 24mm (X-drilled) M426CD 108.00
Front Rotor Cosworth 283 x 24mm (Grooved) M426G 130.00
Rear Rotor Cosworth 273 x 10mm (standard) 45.00
Rear Rotor Cosworth 273 x 10mm (X-drilled) 65.00
Rear Rotor Cosworth 273 x 10mm (Grooved) 86.50
Front Rotor Scorpio 260 x 24mm (standard)G425 49.75
Front Rotor Scorpio 260 x 24mm (X-drilled)G425CD 99.00
Rear Rotor Scorpio 253 x 10mm (standard)G425R 39.75
Rear Rotor Scorpio 253 x 10mm (X-drilled)G425RCD 92.10
Front Brake Kit- BAT R/S 285 x 24mm (standard) M418 339.00
Front Brake Kit- BAT R/S 285 x 24mm (x-drilled) M418A 395.00
Front Brake Kit- Wilwood 283 x 24mm M417 645.00
Front Brake Kit- Wilwood 300 x 32mm M416A 1295.00
Front Brake Kit- Wilwood 300 x 32mm (Scorpio) G416A 1395.00
Rear Brake Kit- Wilwood 300 x 21mm 1200.00
Front Wheel Bearing Kit (RH)-XR M560FR 42.00
Front Wheel Bearing Kit (LH)-XR M560FL 42.00
Front Wheel Bearing Kit (RH) Scorpio G560FR 59.00
Front Wheel Bearing Kit (LH) Scorpio G560FL 59.00
Rear Wheel Bearing Kit (RH)-XR M560RR 42.00
Rear Wheel Bearing Kit (LH)-XR M560RL 42.00
Rear Wheel Bearing Kit (RH) Scorpio G560RR 98.75
Rear Wheel Bearing Kit (LH) Scorpio G560RL 98.75
Nut- Front Hub (LH) blue M550N-LF 6.65
Nut- Front Hub (RH) yellow M550N-RF 6.65
Nut- Rear Hub (LH) white M550N-LR 7.42
Nut- Rear Hub (RH) white M550N-RR 7.42

Pages 28-30
Pricing is listed with part numbers on these pages
PAGE 31 engine & related
Distributor Cap H.D. 2.3L L9B 16.98
Distributor Rotor H.D. 2.3L (85-86 screw-down type) L9F 7.50
Distributor Rotor H.D. 2.3L (87-89 push-on type) L9FA 8.90
TFI Module 2.3L -Motorcraft XR & Scorpio L9M 80.75
Distributor* 2.3L L9AB 119.00
*this item requires an additional 35.00 charge refundable upon core return
Distributor* 2.9L V6G9AB110.25
*this item requires an additional 55.00 charge refundable upon core return
Computer* XR4Ti (specify auto or manual) M9C 143.50
Computer* Scorpio (specify auto or manual) G9C 143.50
*this item requires an additional 75.00 charge refundable upon core return
Electric Fan Switch -XR M450FS 24.50
Knock Sensor -XR M450KS 52.70
Engine Coolant Temp. Sensor (ECT) -XR & Scorpio M450EC 28.45
Idle Speed Sensor (Air Bypass Valve) -XR & Scorpio M450IS 79.90
Throttle Position Sensor (TPS) -XR (order with year) M450TP 47.60
Oxygen Sensor -XR M450OS 60.50
Oil Pressure Switch -XR M450P 6.40
Water Temp Gauge Sender (purple band) -XR M450F 39.75
Air Charge Temp Sensor (ACT)- Scorpio G450A 29.25
Coolant Temp. Sensor (ECT)- XR & Scorpio M450EC 28.45
MAP Sensor -Scorpio G450M 97.50
Oil Pressure Switch -Scorpio G450P 6.00
Oxygen Sensor -Scorpio G450OS 114.50
Vehicle Speed Sensor- Scorpio G450S 119.00
Throttle Position Sensor- Scorpio G450TP 153.00
A/C Compressor -XR & Scorpio M470C 449.00
Alternator* -XR M24A 235.00
Alternator *-Scorpio G24A 235.00
*this item requires an additional 10.00 charge refundable upon core return
Starter* -XR M23A 87.50
Starter* -Scorpio G23A 220.00
*this item requires an additional 30.00 charge refundable upon core return
Fuel Injector 35lb. XR4Ti (Brown Top) remanM7G 49.50
Fuel Injector 35lb. (Disk Type)
new DISCONTINUED
Vane Air Meter* 50mm (T-Bird) L7V 164.50
Vane Air Meter* 65mm (SVO) L7VA 175.00
Vane Air Meter* XR4Ti Standard L7VM 255.00
*this item requires an additional 75.00 charge refundable upon core return
Fuel Pressure Regulator -XR M7PR 52.35
Electric Fuel Pump- XR (high pressure) in line M10A 165.00
Electric Fuel Pump- XR (low pressure) in tank M10AT 125.00
PAGE 32 transmission related
Oil Seal- input shaft (front) T9 M703 9.30
Gasket- input bearing retainer to main case T9 M702G 2.05
Gasket- top cover T9 M716 6.75
Oil Seal- extension housing (tail shaft) T9 M719 11.80
Gasket- adaptor plate (bearing carrier) to main case T9 M709 4.95
Gasket- adaptor plate (carrier) to ext. housing (tail) T9 M708 6.80
Short Shift Kit M715 55.00
Shifter- competition gear lever (shifter) assembled M717 114.50
Torco Gear Oil (quart) C2S 10.25
Quadrant & Pawl Kit M368 18.90
Transmission T9 (remanufactured) M700 CALL
PAGE 33-34
Pricing is listed with part numbers on these pages
4 0 Price List03/27/02
NEW ITEMS.... Too Late To Classify
Valve Cover Gaskets H.D. 2.9L V6 (h.d. rubber)G15EA 15.50
Head Gasket 2.9L V6 (RH) G15DR 22.50
Head Gasket 2.9L V6 (LH) G15DL 22.50
Main Bearing Set 2.9L V6 (specify size) G16A 53.10
Rod Bearing Set 2.9L V6 (specify size) G16H 31.05
Weather Seal - Rear Hatch to Body -Scorpio G340HS 80.00
Electric Window Switch (door/console)- Scorpio G340S 31.10
Rear Sensor Wiring (low pad warning) Scorpio G420SWR 39.45
Vacuum Modulator- A4LD Auto Trans G750M 26.00
Shop Manual T9 Transmission M201 13.95
Weather Seal- Rear Hatch to Body- XR M340HS 79.90
Moulding/Seal Front Windshield-XR M340F 30.00
Weather Seal- Sunroof Opening- XRM340SR 71.00
Weather Strip- Sliding Sunroof Panel- XRM340SRP 24.25
Electric Window Switches (2) Console-XR M340S 47.30
Ignition Switch (Electrical)- XR M350A 41.75
Ignition Lock Cylinder & Keys- XR M350L 69.00
Plastic Rivet- for exterior body cladding- XR M366R .75
Wiper Link Arm (long) ties L & R arms- XR M369 14.35
Wiper Motor Link Arm (short) XR M369A 14.35
Front Sensor Wiring (low pad) XR & Scorpio M420SW 32.50
Bushing- Body Baem Mount Standard M429 36.00
PCV Valve- XR M450V 5.00
Rotary Fan Switch HVAC- XR M470FS 60.00
Rear Wheel Bearing Carrier- XR M550BC 96.25
Rear Stub Axle (LH) XR & Scorpio M550SL 129.00
Rear Stub Axle (RH) XR & Scorpio M550SR 129.00
Transmission Shift Rail Bushing (in case) M718 2.55
Transmission Shift Bushing (on shaft @ shifter) M715B 2.95
Vacuum Modulator- C3 Auto Trans M750M 26.00
(rear)
(center)
Scorpio Exhaust Components- Scorpio exhaust system
components are generally both expensive and difficult to have
reproduced by the local muffler shop. The center section with
all its close proximity twists and bends makes for some real
aggravation. BAT can supply original quality replacement
exhaust parts at very attractive pricing. Center sections are
one piece and include the main muffler, connecting from the
catalytic converter to rear resonator. Rear sections are standard
type rear (can) resonator.
Scorpio Center Muffler Section G522 $149.00
Scorpio Rear Resonator Section G522T $90.00
Exhaust Hanger (each) C522H 5.95
New