1993 FORD SIERRA brake rotor

pA Front Caliper We offer high quality re-manufactured
front calipers which are considerably less costly than new.
Calipers are handed left & right and require return core charge.
(drivers- left) M420CL(passenger- right) M420CR
pB
Caliper Repair Kit -w/piston Ford caliper repair kits are
an economical way to service a leaking or "sticky" caliper. Fitting
this kit, after honing the piston bore, will cure most caliper related
problems. (kit does 1 caliper)M420K4A
pC
Caliper Seal Kit After inspection many calipers only
require new seals to put them right. (kit does 1 caliper) M420K4
pD
Performance Street Brake Pad Set Premium
Mintex A/F series brake pads will give enhanced brake perform
over a wide temperature range with very little brake dusting.
Mintex pads also incorporate the pad warning sensor wiring.
This is the abusolute best performing street pad we have tested
and for the price they are a steal.
(XR4 & Scorpio)M420M
pD
Racing Brake Pad Sets Mintex 1144 is a rally/race pad
that is perfectly at home on track or street, offering a high coefficient
of drag (.44) and excellent modulation throughout a very wide
operating range (up to 1200 degrees). Mintex 1144 is supplied pre-
burnished for easy break-in and minimal fade on the first heating
cycle. Both fade resistance and wear characteristics are excellent.
Mintex pads are the only racing brake pads to incorporate the
standard "low pad" sensor wiring. Match a set of these pads with our
drilled or grooved sport rotors and Aeroquip stainless brake lines for
a substantial increase in braking performance.
(XR4 & Scorpio)
Mintex Street/Competition (M1144)M420G
Mintex Full Competition (M1155) M420GA
pE Standard Front Rotors Lesser quality generic "white
box" rotors tend to warp easily, don't even consider fitting them
on your XR4 or Scorpio. BAT supplies only the highest quality
(Brembo -
Italy & United Brake -England) rotors at better than
"bargain" rotor prices. (each)
XR4 M425
Scorpio G425
pE
pC
pD
pD
pA
pB pF
Brake System (front)
pH
See price list for caliper
slide bushings and pins
pG
0 7
check price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items
pF Cross Drilled Front Rotors Cross-drilling brake
rotors is an excellent way to increase brake performance.
Theory being that centrifugal force will draw excess brake
dust and expelled gasses from the pad surface through the
drilled passages into the rotors vented cavity and out. This
process also improves rotor cooling giving improved braking
response and resistance to fade. Our drilled brake rotors
are made from Carballoy (a medium flake graphite fully
pearlitic low phosphorous iron) manufactured to BS 1452
- 1990 grade 180/220 standard. The cross drilling process
is handled by computer CNC milling equipment with holes
arranged in a parabolic pattern giving an even sweeping
effect to the pad surface ensuring maximum cooling with
minimum noise and drag. M425CD
*rotors must by purchased as (handed) pairs- priced as each
Grooved Front Rotors As an option we can supply
slotted (grooved) pattern rotors which are manufactured to
the same high standards as the above listed cross drilled
versions.M425S
*rotors must by purchased as (handed) pairs- priced as each
Drilled & Slotted Front Rotors As an option we can
supply combination drilled & slotted (grooved) pattern
r o t o r s manufactured to the same high standards as the above
listed cross drilled versions.M425CDS
*rotors must by purchased as (handed) pairs- priced as each
pG Master Cylinder high quality Bendix replacement power
brake master cylinder.
(specify year when ordering)M420MC
pH
Aeroquip Brake Lines One of the more effective brake
modifications you can make is to replace the standard brake
hoses with Aeroquip steel braided lines. These performance
brake hoses incorporate a teflon interior to keep line expansion
"flexing" to a minimum. This greatly reduces the "spongy" pedal
feel common to the XR4 & Scorpio brake system. Our stainless
lines are assembled from genuine Aeroquip AN-3 hose with
premium metric "reusable" (not the lesser quality "swaged" type)
hose ends installed. XR4Ti (state year) M419
Scorpio G419

pC
pDpBpA
pA Front Brake Special 260 x 24mm
This kit is just the thing for replacing the standard size, wear related,
front brake components. We supply high quality Euro specification
rotors and premium Mintex brake pads for either XR4 or Scorpio and
at a special price as compared to buying items separately.
Front Brake Special XR4ti M420SP
Front Brake Special Scorpio G420SP
pB
BAT R/S Front Brake Kit (283 x 24mm) XR4ti
BAT R/S Brake Kit allows larger 11.25" (283mm) Cosworth brake
rotors to be fitted with standard XR calipers. Increasing rotor "swept
area" in this way will greatly improve stopping power (leverage) and
help to reduce high brake temperatures that can cause premature
brake fade and poor pedal feel. Kits are available in 4 different
component levels from as little as $295.00, which leaves you no
reason not to upgrade to larger brakes.
Kits include: 285 x 24mm
vented (standard or cross-drilled) rotors, Mintex brake pad set
(standard or M1144), caliper mounting brackets & hardware (fitment
with most 15" and larger wheels -some require modification or
spacers)
Front R/S Brake Kit (283 x 24mm) M417
includes standard rotors, standard Mintex pads, brackets & hardware
Front R/S Brake Kit (283 x 24mm) M417A
includes X-drilled rotors, standard Mintex pads, brackets & hardware
Front R/S Brake Kit (283 x 24mm) M418
includes standard rotors, M1144 Mintex pads, brackets & hardware
Front R/S Brake Kit (283 x 24mm) M418A
includes X-drilled rotors, M1144 Mintex pads, brackets & hardware
pC BAT/Wilwood Front Brake Kit (283 x 24mm) XR4ti
This kit combines the performance of the larger 283mm Cosworth rotor
with Wilwood 4 piston Superlite 2A calipers which are extremely ridged
and transfer torque directly without unwanted flex. Construction is
aluminum with stainless pistons for both weight savings and maximum
head dissipation. At just 5 lbs. they are also much lighter than stock
calipers. This goes a long way to reducing "unsprung" weight benefiting
both braking and handling performance.
Kit includes: 285 x 24mm
vented rotors, 4-piston alloy Wilwood Superlite IIA calipers with pads
and aeroquip brake hoses (fitment with most 15" and larger wheels -
some require modification or spacers)
M416W
pD
BAT/Wilwood Front Brake Kit (300 x 24mm) XR4ti
This kit combines even larger 300mm Cosworth rotor with Wilwood
4 piston Billet Dynalite for the ultimate big brake kit. Calipers are
extremely ridged and transfer torque directly without unwanted
flex and are made from aluminum with stainless pistons for both
weight savings and maximum head dissipation. At just 4 lbs. they
are also much lighter than stock calipers. This goes a long way to
reducing "unsprung" weight benefiting both braking and handling
performance.
Kit includes: 300 x 24mm vented rotors , 4-piston
alloy Wilwood Billet Dynalite calipers with pads and aeroquip
brake hoses (fitment with some 15" & most 16" and larger wheels
-some require modification or spacers)
M416W3
Brake Kits & Specials0 8

pA
pBpC
pEpD
pE Rear Brake Parts Kit This handy kit includes all of the
small parts, springs and other attaching hardware for the rear
drum brakes. One kit does both hand sides.M420K5
Rear Brake Special Our rear brake special has all the
items (brake shoes, wheel cylinders & small parts kit)
required for a complete rear brake overhaul, and all at a very
attractive price.M420RSPL
pF
Rear Disk Brake Kit Converting to rear disk brakes
could not be any easier than with our ventilated rear disk
conversion kit. Not only will braking performance be greatly
improved but servicing the friction material (pads) becomes a
much easier task than messing with the old shoes. Kit incudes:
calipers & mounting plates, vented 260mm rotors, brake lines,
hand brake cables, and assorted hardware.M420RK
Note: see price list for individual listings on service parts for
above rear disk brake kit.
XR4 & Scorpio Hand Brake Cables We have replacement
hand brake cable assemblies for both the XR4Ti and Scorpio.
These have been recently discontinued by Ford USA.
Hand Brake Cable XR4Ti M564
Handbrake Cable Scorpio G564
Cosworth Hand Brake Cable required for fitting a
Cosworth rear brake conversion to the XR4 or servicing cars
with existing Cosworth rear brake cables.Z16567
Scorpio Rear Brake Components BAT also stocks
brake components for servicing and upgrading the rear
brakes on the Merkur Scorpio.
Rear Rotor (standard) G425R
Rear Rotor (cross drilled) G425RCD
Rear Caliper (left or right) G420RL/RR
Rear Pad Set G420R pA
Rear Wheel Cylinder Backing plates should be checked
periodically for brake fluid drips or a damp spot at the bottom (a sure
sign of a leaky wheel cylinder). We recommend (and sell) only new
replacement wheel cylinders because of the high incidence of
failure found with re-manufactured units.M420WC
pB Rear Brake Shoes Our premium quality rear brake shoes
are supplied as either European Motorcraft or Mintex brand. Both
are new (non re-manufactured) high quality semi-metallic
replacement linings, not the typical "white box specials".
Note:
fitting reman rear shoes can be a problem as most we have seen
have thicker than standard bonded linings making it difficult, if not
impossible, to reinstall the drum.
M420R
pC
Rear Brake Drum Brake drums that are warped or
beyond minium specification for wear should be replaced.
New rear brake drums are sold each.M420RD
pC
Rear Brake Drum (Grooved) These rear drums offer
an extra degree of braking performance not found when
using standard rear drums. Drums have 12 spiral grooves
for maximum cooling and deglazing effect. Grooved drums
are sold in handed pairs.M420RDG
pD
Aeroquip Rear Brake Lines One of the more effective
brake modifications you can make to the XR4 & Scorpio is to
replace the standard brake hoses with Aeroquip steel braided lines.
These performance brake hoses incorporate a teflon interior to
keep line expansion "flexing" to a minimum. This greatly reduces
the "spongy" pedal feel common to most brake systems. Our
stainless lines are assembled from genuine Aeroquip AN-3 hose
with premium metric "reusable" (not the lesser quality "swaged"
type) hose ends installed.
XR4 Rear Aeroquip Brake Line Set M419R
Scorpio Rear Aeroquip Brake Line Set (4 lines)G419R
Brake System (rear)
check price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed itemscheck price lists for Scorpio versions of listed items check price lists for Scorpio versions of listed items
check price lists for Scorpio versions of listed items
pF
0 9

Brake (related)
pA
pEpA
Racing Brake Fluid Not all brake fluid is created equally. High
operating temperatures at the caliper transfers extreme heat through the piston
causing lesser quality brake fluid to boil. This in turn allows the fluid to become
compressed and reduces overall braking performance. The best way to
counter this from happening is to use a racing specification, mineral (never
synthetic) brake fluid and flush the system after each event for competition or
annually on performance street driven vehicles. Both AP550 and Wilwood 570
brake fluid is DOT approved with a dry boiling point of 550-570 degrees, low
viscosity minimizes aeration and permits easy bleeding.
Brake Fluid AP Competition (16.9oz. 500ml.) MC550
Brake Fluid Wilwood 570 (12oz. 355ml.) MC570
Brake Fluid Wilwood 570 (6 Pack) MC57-6
Brake Fluid Wilwood 570 (24 Case) MC57-C
pB
Cosworth & Scorpio Rotors For those fortunate few who own
Cosworth Sierras or have converted XR4's to Cosworth type front or rear brakes
and are in need of replacement rotors we have them. Scorpio front or rear rotors
in standard and cross drilled are also available. (see price list page 31)
Cosworth Front 283 x 24mm standard, X-drilled, grooved
Cosworth Rear 273 x 10mm standard, X-drilled, grooved
Scorpio Front 260 x 24mm standard or X-drilled
Scorpio Rear 253 x 10mm standard or X-drilled
Performance Brake Kits Engineered competition brake kits for the
ultimate in stopping power.
pC Front R/S Brake Kit (283 x 24mm)
BAT R/S "big brake" kit allows larger 11.25" (285mm) brake rotors to be fitted
with standard XR calipers. Increasing rotor "swept area" in this way will greatly
improve stopping power (leverage) and help to reduce high brake temperatures
that can cause premature brake fade and poor pedal feel.
Kit includes:
285 x 24mm vented (standard or cross-drilled) rotors, Mintex 1144 brake pad
set, caliper mounting brackets & hardware (fitment with most 15" wheels -
some require slight modification)
kit supplied with standard rotors
M418
kit supplied with cross drilled rotors M418A
pD Front Brake Kit (283 x 24mm) w/4 Piston Calipers
Combine the performance of the R/S large rotor kit with 4 piston calipers for the
ultimate in stopping power.
includes: 283 x 24mm vented rotors,
4-piston alloy Wilwood Superlite 2A calipers with pads. (fitment with most 15"
wheels -some require modification or spacers)
M416W
pD Front Brake Kit (300 x 32mm) w/4 Piston Calipers
For those who are looking for the ultimate brake performance. Quite simply the
largest and most competent competition type brake kit that can be fitted to the XR4.
includes: 300 x 32mm vented rotors with light alloy hats, 4-piston alloy Wilwood
Superlite IIA calipers, caliper mounting brackets & hardware
M417A
(this kit also available for Scorpio ! ) G417A
Rear Kit (XR4 w/16" wheels) 300 x 21mm (See Price List)
includes: 300 x 21mm vented rotors with light alloy hats, 4-piston alloy Wilwood
Superlite 2A calipers, caliper mounting brackets & hardware
pE Wheel Bearings Genuine European Ford wheel bearing kits are
complete with all required service parts to do a first class job. Each kit
include bearings, races, seals and hub nuts to service one wheel.
Front Wheel Bearing Kit (specify left or right) -XR4 M560F
Rear Wheel Bearing Kit (specify left or right) -XR4 M560R
Front Wheel Bearing Kit (specify left or right) -Scorpio G560F
Rear Wheel Bearing Kit (specify left or right) -Scorpio G560R
pB
pC
pD
1 0

07/30/02Price List3 6
PAGE 10 driveline components
C.V. Joint- XR & Scorpio M550B 92.50
C.V. Boot Kit- XR & Scorpio M550BK 14.90
C.V. Socket Head Cap Screw (6 per joint) M550CS 1.05ea
C.V. Locking Plate (3 per joint) M550LP 1.35ea
Axle/Halfshaft Complete* (LH)- XR & Scorpio M550L 169.50
Axle/Halfshaft Complete* (RH)- XR & Scorpio M550R 169.50
*axle/halfshaft, joints (2), boots (2), assembled/greased ready for installation
add 75.00 core charge for this item- refundable on return
Driveshaft Coupling- XR & Scorpio M17A 62.50
Drivesahft Center Support Bearing-XR M550SB 109.75
Drivesahft Center Support Bearing- Scorpio G550SB 98.00
Quaife LSD M710 1245.00
Clutch Kit Sachs- XR M519K 179.50
Clutch Kit Sachs- Scorpio G519K 257.50
Clutch Kit Sachs- XR w/ T-5 trans M519T5 179.50
H.D. Clutch Kit Centerforce (30% kit) M519C 309.95
H.D. Clutch Kit Centerforce II (50% kit) M519C2 361.98
Clutch Alignment Tool (1" 23 spline) S11H 6.00
Clutch Cable- XR4Ti M562 29.50
Clutch Cable- Scorpio G562 76.50
BAT is always testing and
developing new products....if
you don't see it listed ask... we
might have what you are looking
for, or can point you in the right
direction.
PAGE 8 brake kits & specials
Front Brake Spacial- XRM420SP 105.00
Front Brake Spacial- ScorpioG420SP 115.00
Front R/S Brake Kit 283x24mm (standard) M417 295.00
Front R/S Brake Kit 283x24mm (w/x-drill) M417A 329.00
Front R/S Brake Kit 283x24mm (standard/M1144 ) M418 339.00
Front R/S Brake Kit 283x24mm M1144/x-drill) M418A 395.00
BAT/Wilwood Brake Kit 283mm M416W 645.00
BAT/Wilwood Brake Kit 300mm M416W3 725.00
PAGE 9
rear brake components
Rear Wheel Cylinder- XRM420WC 35.95
Rear Brake Shoe Set (Motorcraft/Mintex)- XRM420R 49.95
Rear Brake Drum
- XRM420RD 74.00
Rear Brake Drum (grooved)
- XRM420RDG 129.50Aeroquip Rear Brake Lines (pair)- XRM419R 47.50
Rear Brake Line O.E. Rubber (each)- XR4 (1985-89)M419SR 27.45
Aeroquip Rear Brake Lines (4 line set)- ScorpioG419R 85.00Rear Brake Hardware Kit- XR M420K5 25.60
Rear Brake Special- XR M420RSPL 125.00
Rear Disk Brake Kit- XR M420RK 689.00
Hand Brake Cable- XR M564 44.00
Handbrake Cable- Scorpio G564 44.00
Hand Brake Cable- Cosworth Z16567 44.00
Rear Caliper* (specify left or right) for M420RK kit127.50
*this item requires an additional 75.00 core charge refundable upon core return
Rear Rotor (each) for M420RK kit52.50
Rear Brake Pad (set) for M420RK kit25.00
Rear Rotor (standard)- Scorpio (each)G425R 39.75
Rear Rotor (x-drilled)- Scorpio (each)G425RCD 92.00Rear Caliper (left)- Scorpio (each)G420RL 124.50
Rear Caliper (right)- Scorpio (each)G420RR 124.50
*this item requires an additional 75.00 core charge refundable upon core returnRear Brake Pad Set- Scorpio (Semi-Metalic)G420R 39.00
ABS Brake Sensor Scorpio/XR4- Rear G420SR 177.25
PAGE 7 front brake components
Front Caliper* (left)- XR & Scorpio M420CL 64.75
Front Caliper* (right)- XR & Scorpio M420CR 64.75
M420CL/CR calipers are not supplied with slide pins or bushings (available below)
Front Caliper Complete* (LH) includes mount & pads M420CL-L 90.00
Front Caliper Complete* (RH) includes mount & pads M420CL-R 90.00
*this item requires an additional 75.00 charge refundable upon core return
Caliper Repair Kit- XR & ScorpioM420K4A 55.00
Caliper Seal Kit-
XR & ScorpioM420K4 17.75
Caliper Slide Bushings (2) does 1 caliper M420CB 14.00
Caliper Slide Pins (2) does 1 caliper M420CP 16.35
Caliper Spring (anti-rattle) each M420CS 6.39
Front Brake Pad Set*- Mintex A/F (Semi-Metalic) M420MM 39.00
Front Brake Pad Set*- Mintex 1144 (street/competition) M420G 75.00
Front Brake Pad Set*- Mintex 1155 (full competition) M420G 112.30
*brake pads will fit both XR4 and Scorpio
Front "Low Pad" Sensor Wiring Harness- XR/Scorpio M420WS 32.49
Front Rotor (standard)- XR (each)M425 42.50
Front Rotor (standard)- Scorpio (each) G425 49.75
Front Rotor (x-drilled)- XR (each)M425CD 79.50
Front Rotor (x-drilled)- Scorpio (each) G425CD 99.00
Front Rotor (x-drilled & slotted combo)- XR (each)M425CDS 89.50
Front Rotor (x-drilled & slotted combo)- Scorpio (each)G425CDS 109.00
Master Cylinder* XR4 1985-86 (Bendix)- XRM420MC 109.50
*this item requires an additional 20.00 charge refundable upon core return
Master Cylinder* XR4 1987-89 (Bendix)- XRM420MCL 122.50
*this item requires an additional 50.00 charge refundable upon core return
Aeroquip Front Brake Lines (pair)- XR4 (1985-88)M419 42.50
Front Brake Line O.E. Rubber (each)- XR4 (1985-86)M419SF 25.75
Aeroquip Front Brake Lines (pair)- XR4 (1987-89)G419 52.40
Aeroquip Front Brake Lines (pair)- ScorpioG419 52.40
ABS Brake Sensor Scorpio/XR4- Front G420SF 179.75
PAGE 11 brake components
Brake Fluid AP550 (500 ml) MC550 10.70
Brake Fluid Wilwood 570 (355 ml) MC570 5.95
Brake Fluid Wilwood 570 (6-pack) MC57-6 33.00
Brake Fluid Wilwood 570 (24 case) MC57-C 119.00
Front Rotor Cosworth 283 x 24mm (standard) M426 75.00
Front Rotor Cosworth 283 x 24mm (X-drilled) M426CD 108.00
Front Rotor Cosworth 283 x 24mm (Grooved) M426G 130.00
Rear Rotor Cosworth 273 x 10mm (standard) 45.00
Rear Rotor Cosworth 273 x 10mm (X-drilled) 65.00
Rear Rotor Cosworth 273 x 10mm (Grooved) 86.50
Front Rotor Scorpio 260 x 24mm (standard)G425 49.75
Front Rotor Scorpio 260 x 24mm (X-drilled)G425CD 99.00
Rear Rotor Scorpio 253 x 10mm (standard)G425R 39.75
Rear Rotor Scorpio 253 x 10mm (X-drilled)G425RCD 92.10
Front Brake Kit- BAT R/S 285 x 24mm (standard) M418 339.00
Front Brake Kit- BAT R/S 285 x 24mm (x-drilled) M418A 395.00
Front Brake Kit- Wilwood 283 x 24mm M417 645.00
Front Brake Kit- Wilwood 300 x 32mm M416A 1295.00
Front Brake Kit- Wilwood 300 x 32mm (Scorpio) G416A 1395.00
Rear Brake Kit- Wilwood 300 x 21mm 1200.00
Front Wheel Bearing Kit (RH)-XR M560FR 42.00
Front Wheel Bearing Kit (LH)-XR M560FL 42.00
Front Wheel Bearing Kit (RH) Scorpio G560FR 59.00
Front Wheel Bearing Kit (LH) Scorpio G560FL 59.00
Rear Wheel Bearing Kit (RH)-XR M560RR 42.00
Rear Wheel Bearing Kit (LH)-XR M560RL 42.00
Rear Wheel Bearing Kit (RH) Scorpio G560RR 98.75
Rear Wheel Bearing Kit (LH) Scorpio G560RL 98.75
Nut- Front Hub (LH) blue M550N-LF 6.65
Nut- Front Hub (RH) yellow M550N-RF 6.65
Nut- Rear Hub (LH) white M550N-LR 7.42
Nut- Rear Hub (RH) white M550N-RR 7.42