1992 MITSUBISHI 3000GT lock

Downloaded from www.Manualslib.com manuals search engine 234
CIRCUIT DIAGRAMS - Central Door Locking Circuit
CENTRAL DOOR LOCKING CIRCUIT (FROM 1996 MODELS) (CONTINUED)
IGNITIC--SWITCHIN(ACC)
5W-B 1HdRN
l(c-68)(C-EJ/B lI
69
10A
(c-7o,y--“2
R R-Y
,.l ,.20.85R-B
\ -
IOD OR
STORAGE
CONNECTOR
(A-11X)
300p
(HATCHBACK)R-B
DOME LIGHT -11
(F)R-B
I
R-B1R-B1
(RH)
c-35
R-B
BUZZERr-r-_KEY REMINDER
VEHICLES WITH
THEFT-ALARM
DOME LIGHT.FOOTLIGHT AND IGNITION
KEY CYLINDER
ILLUMINATION LIGHT
B-LI
L7h I
NOTExlm;EbES WITHOUT THEFT-ALARM
"2:;;g'/gkES WITH THEFT-ALARM
:3:;&g+gkES WITH KEYLESS ENTRYI
TRANSMITTER x3KEYLESS ENTRY CONTROL UNIT-
HRllMO7BA1
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Central Door Locking Circuit235
FUSIBLE LINK0
R-B
1(c-66) 51ETACS UNIT(c-65)4
Inhn""YI
STORAGE
CONNECTOR
(A-11X)
(F>R-B
;I;" LIGHT
LUGGAGE
COMPARTMENT
LIGHT
GNDn
i
--254j7:4jg $5
G-Y
B
(F)
----_6:5
R-G
R-G
4:4
R-G 1
ir
---OFFOFF - ON - ON
1
G-Y.J
I
G-YD
II=
GND GND
kxmJ77~oB B
KEY REMINDER
SWITCH
Bw&BSTHEFT-ALARM
(c-58) B5 4
"v vj2B
LINKXTORA DATACONNI
DOORSWITCH (LH)
lM07BB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Central Door Lockina Circuit
COMPONENT LOCATION
NameSymbol
Name
Symbol
Data link connector (from 1994 models)
DDoor lock power relay 2 (Concerning the ve-
hicles up to 1993 models, only for the vehicles
equipped with keyless entry system.)
Data link connector (up to 1993 models)AETACS unit
Door lock actuator
Door lock power relay 1EKeyless entry control unitF
B
I \W16FO268
N19F013400002664
Y16FO354
actuator
Y16FO202
) u
\Y16FO49f
lay2
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Central Door Locking Circuit237
OPERATION/
Li!l
When the door lock switch is set to the LOCKside (or UNLOCK side), the LOCK side (or
UNLOCK side) of the door lock relay is turned
ON and the door actuators of all doors operate.l
If the driver seat side door (or assistant seat
side door) is opened and the driver seat side
inside lock knob (or assistant seat side inside

0
,’
id
0
With the driver’s and front passenger’s doorsunlocked, press the LOCK switch of the
transmitter, and the door lock signal output (0V) will be sent from the
keyless entry control
unit terminal No. 12 closing the door lock powerrelays 1 and 2 to lock the driver’s and front
passenger’s doors.
While the R.H. and L.H. doors are in the lockedstate, press the UNLOCK switch of the
transmitter once, and the DOOR UNLOCK
switch signal (0 V) will be sent from the keylessentry control unit terminal No. 14 closing the
door lock power relay 2 to unlock the driver’s
door.
Under the above-mentioned conditions, further
press the UNLOCK switch of the transmitter,and the DOOR UNLOCK signal output (0 V)
will be sent from the keyless entry control unitterminal No. 13 closing the door lock power
relay 1 to lock the front passenger’s door.
When the keyless entry system is operated toturn the driver’s door lock switch from the
UNLOCK position to the LOCK position, thelock knob) is locked with the key inserted in
the ignition switch, the ETACS unit grounds the
unlock side circuit of the door lock relay to unlock
all doors. This way, failure to remove the key
is prevented.dome light/foot light blinking signal output
(system voltage) will be sent twice from the
keyless entry control unit terminal No. 11 when
the door lock switch is turned from the LOCK
position to the UNLOCK position, the lighting
signal output (0 V) will be provided for approx.
3 seconds.
NOTE
The dome light winks or comes on when the domelight switch is in the DOOR interlock position.
However, the dome light does not wink while it .is
ON for 6 seconds after closing the door by ETACS
function.Besides the above-mentioned operations, the
keyless entry control unit has the following functions.l
If any door is not opened or closed within 30
seconds from unlocking the door by means ofthe
keyless entry system, the door is
automatically locked.In addition, if the
cryptographic code other than the code storedin the receiver memory is received 30 times
in one minute continuously, operation of the
unit is suspended for 10 minutes.l
Operation is also suspended if the ignition key
remains inserted (key reminder switch: OFF)
and either door is left open (door switch: ON).TROUBLESHOOTING HINTS

Phenomenon
Inspection method
One of the door lock actuators fails to operate.
0Check the door actuator which fails to operate.
No unlock operation can be made by pressing door lock0
knob after fulfilment of following conditions.Check the key reminder switch input signal.0Check the key reminder switch. (Refer to GROUP
0Insertion of key in ignition switch (key reminder switch54-Ignition Switch.)
OFF)0
0Opening of door (door switch ON)Check the front door switch input signal.0 Check the front door switch. (Refer to GROUP
42-Door Assembly)
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 238CIRCUIT .DIAGRAMS - Central Door Locking Circuit
l
The indicator does not blink after pressing thetransmission switch of the transmitter.
1) Check or replace the battery. (Refer to
GROUP
42-Keyless Entry System.)
2) Replace the transmitter.
l Transmitted wave is being sent from thel
R.H. and L.H. doors can be locked and unlocked
by the transmitter but the dome light and footlight do not blink or come on. (Interlocked
lighting of the dome light and foot light by means
of the dome light switch or door opening and
closing is normal).
transmitter (indicator is blinking), but the system
does not operate.1) Check the cryptographic code registering
method. (Refer to GROUP
42-Keyless
Entry System.)
2)Check the keyless entry control unit terminalvoltage. (Refer to GROUP
42-Trouble-
shooting.)3) Check the coaxial cable of antenna and
the ground wire for connection.
l Only R.H. or L.H. door can be locked or
unlocked.
1)Check the door lock power relay 1 (for front
passenger’s door) or door lock power relay2 (for driver’s door). (Refer to GROUP
42-Central Door Locking System.)
2)Check the keyless entry control unit terminalvoltage. (Refer to GROUP
42-Trouble-
shooting.)
1)Check the keyless entry control unit terminal
voltage (Refer to GROUP
42-Troubleshoot-
ing.)2) Check the harness.
NOTE
l :Perform this check when replacement of the
transmitter and/or
keyless entry control unit or
faulty storage of cryptographic code has been
made.
\
Ilj
‘d I
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Manual Air Conditioning Circuit243
2-LR
2L-I?
c.
G
EYkiB5Etz
AIR COb
EKE:
(G-C
DEDICATED
FUSEL-----
2L-w
G-C
CONDENSER
.
;-FA;OTOR
OLdOFF, (HI) (LO) OFF-$3N,4(A-31X)(A-34X) "4
2B
2LE
,,l______--_----___,,4(A-37)
2L-w2L
1 1
TIONING1: LOCKRADIATOR FANMOTOR RELAYCLO)7
L-l
i
G-O
] f#?~f~R[
1(A-32X)
B
2L-E
(A-36)
B2L-B2
0 c
2B
L-C
i
.-----_
OF
1.
L-G--------1
.___-___-__-----_J
9
HR12MOlAB
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Manual Air Conditioning Circuit245
AIR~~~~~~10"'""J/B
ib#&PURPOSE1
AIR CONDITIONING
COMPRESSOR LOCK
CONTROLLER
11
CIRCUITI
I%%I%;:Y,C"IT\GNDGND
(W-E
COMBINATIONMETERCTACHO)
-.c
W(W-B
IGPPO)TRI
(G-Y)
i(D-42)
ION
ISTOR
14
I(B
7
;
I
)(B)
28
HR12MOlBB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Manual Air Conditioning Circuit247
AIR CONDITIONINGCOMPRESSOR LOCK BLCONTROLLERSW
(G-!
I6VT7
RHEOSTAT
W-E
'ER
FHw
1.25R-'
G-WG-h
(c-18)
AIRg&I;;;IONINGG-b
,3,\
,$IG
J
I 6
HT
-
DEDICATED
FUSE
J/B
,VIv\/ \, ,
"2
"45 6
R-YL-B(B-R) B-YB-Y0
B-Y
HR12MOlCB
TSB Revision