1992 MITSUBISHI 3000GT lock

Downloaded from www.Manualslib.com manuals search engine 54-98CHASSIS ELECTRICAL - Lighting System
STOP LIGHT
CIRCUIT DIAGRAM L)
FUSIBLE LINK@
0.85R-B ‘7 (c-83)
WITHE;$FiEFUISEIWITHOUT
_AUTO-CRUISE
CONTROL
t.MFI SYSTEM. &&~EU'SE
(c-61)(c-62)
0.85G
0.85G
0
2B
h=
0.85G
!
HIGH MOUNTED BSTOP LIGHT
m
2B
0.85G5(F-'iS)
t
0.85G3mG42
0.85G
I
i-ANTI-LOCK BRAKING SYSTEM
2.ELECTRONIC CONTROLSUSPENSIONz3
REAR
COMBINAT
LIGHTCRHION)J
NOTEZ'l:VEHICLES WITHOUTACTIVE AERO%E:VEHICLES WITHACTIVE AERO%3:UP TO 1995 MODELS
(c-61) (c-62) (C-68) ET3)(F-04)‘l(F-04)%2 (F-10) (F-19)
@J @ fl pggq& pFtiqw[m~a-~~
HROSMO4AA
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
CIRCUIT DIAGRAM
54-99~
LINK@
FUSIBLE,
i
REARCOMBINATIONLIGHTCLH)G
AY
o-85x 140
0.85Gt
IJ
40
B
!
2B-
+.MFI SYSTEM'#T&cpsF
. ANTI-LOCKBRAKING SYSTEM.ELECTRONIC CONTROLSUSPENSION:
NOTEx:1995 MODELS
(lxn (c-621 (C-68) (c-83)
@Q pJ ~~~~~~1
-
1
4(F-10)
B
2B
q
REAR
COMBINATION
LIGHTCRH)
HROSM05AA
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
Up to 1993 modelsFrom 1994 mod&
__ _..--.
Vertical center lineZ16FO509
JHot
z&ky M-j’ Within~ Within600mm1mm (in.)600 mm
(23.6)
(23.6)
Note l ’ Up to 1993 modelsl 2 From 1994 models
1 Etomj
0000236600002387
LUMINOUS INTENSITY MEASUREMENT
Measure the luminous intensity of headlights with a photo-me-ter in accordance with the instruction manual prepared by
the manufacturer of the photometer and make sure that the
luminous intensity is within the following limit.Limit: 20,000 cd or more
NOTE
(1) When measuring the luminous intensity of headlight, keepthe engine at 2,000 rpm and have the battery charged.
(2) If there are specific regulations for luminous intensity ofheadlights in the region where the vehicle is operated,
make sure that the intensity conforms to the requirements
of such regulations.
FOG LIGHT AIMING
1.Place vehicle on a known level floor 7.6 m (25 feet) from
aiming screen or light colored wall.
2. Use adjusting screw to adjust the top end of high intensity
zone to dimension A.
BULB REPLACEMENT
1. Disconnect the connector.
2. Turn the bulb socket counterclockwise to pull it out.
Caution
Do not touch the surface of the headlight bulb with handsor dirty gloves. If the surface dies become dirty, clean
it with alcohol or thinner, and let it dry thoroughly before
installing.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
16A0833
A(Conductivity
Headlight lower
stop position
16FO17100002390
+B, ROD ASSEMBLY REMOVALUsing a flat head screwdriver (wrap cloth or similar on
the ball joint area to prevent injury), disconnect the connec-
tor.NOTE
When disconnecting the rod assembly from the link, hold
the link by hand.
INSPECTION
POP-UP MOTOR (Up lo 1993 models) CHECKRotate the manual knob of the pop-up motor clockwise by
hand to check continuity between terminals.
TerminalWhen the
(+) terminal of the B
ohmmeter is connected to (1)
and the (-) terminal is connected
to (2)
Continuity rangeWhen the
(+) terminal of the A
ohmmeter is connected to (1)
and the (-) terminal is connected
to (5)
‘1 I
Lj
I
‘d ~~
iji
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-112CHASSIS ELECTRICAL - Column SwitchCOLUMN SWITCH
REMOVAL AND INSTALLATION
1
Removal steps
1. Air bag module (Refer to GROUP525Air Bag Module and ClockSpring.)+A, .A+ 2. Steering wheel3. Knee protector
4Bb
$F$i;)to GROUP 52A - Instrument
4. Column cover, lower
4B,5. Column cover, upper6. Lap cooler duct and foot shower duct7. Column switch, right (For lightingswitch, dimmer/passing switch andturn signal switch)8. Column switch, right (For wiper andwasher switch)
REMOVAL SERVICE POINTS
(A,STEERING WHEEL REMOVAL
Remove the steering wheel by the special tool.
Caution
Do not hammer on the steering wheel. Doing so may
damage the collapsible column mechanism.
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine L
L
CHASSIS ELECTRICAL - Column Switch54-113
Front of vehicles
219FOlZ:
Mating mark-! !kU19FOOE
-
16FO237
16FO1:900002398
+B,COLUMN COVER, LOWER / COLUMN COVER, UP-
PER REMOVAL
After the screws have been removed, remove the covers,while making sure not to break the grippers.
INSTALLATION SERVICE POINT
.A(STEERING WHEEL INSTALLATION
To center the clock spring, line up the “NEUTRAL” markof the clock spring with the mating mark.
CautionIf the clock spring’s mating mark is not properly
aligned, the steering wheel may not be completely
rotational during a turn, or the flat cable within the
clock spring may be severed, obstructing normal op-eration of the SRS and possibly leading to serious
injury to the vehicle’s driver.
INSPECTION
(1) Remove the knee protector and the column cover. (Refer
(2)
to GROUP 52A - Instrument Panel.)
Disconnect the column switch left connector (16 terminals)
and check the continuity between the terminals for each
switch.
LIGHTING SWITCH CHECK
Operate the switch and check the continuity between the termi-
nals.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-116CHASSIS ELECTRICAL - Horn
CIRCUIT DIAGRAM

c
5W-B;;-j
. ANTI-LOCKBRAKING SYSTEM*&$@lJUISE
.BUZZER*E;~CT~R~ DOOR
.DOME LIGHTsFOOT LIGHTAND IGNITION KEY
CYLINDER ILLUMINATION
LIGHT
.DOOR LIGHT AND LUGGAGECOMPARTMENT LIGHT.ELC 4A/T'ELECTRONIC CONTROL
SUSPENSION:
FOG LIGHT
FULL AUTO A/C
'HEADLIGHT
.HEATER
'MANUAL A/C
. MFI SYSTEM.POWER WINDOW.RADIO ANDTAPE PLAYER. REAR WINDOW DEFOGGER. STARTING.STOP LIGHT.SUPPLEMENTAL
RESTRAINT SYSTEM
.TAILLIGHT PARKING/SIDE MARKER LIGHTfJy;H;ICENSE PLATE
.TENSION-REDUCER
TYPE SEAT BELT
.THEFT-ALARM SYSTEM*WINDSHIELD
WIPER AND WASHER
NOTE::UP TO 1995 MODELS
R-B
(A-06X)
I
G-B
(c-02)
G-B
(c-57)
GF
CLOCK
SPRING
[
GE
;;&CATED
G-R
!(
2E=
HORNG-R
(LH)c
E
=
'TCH
G-R
l(A-47),l (A-49)
>HORN
l(A-48)"1 (A-50)
B
0 (A-47) oFa (A-49) ofiml (c-02)(c-57)=
1993 MODELS) (FROM 1994 MODELS)
El
‘J ’
HROSMOSAA
1 TSB RevisionI

Downloaded from www.Manualslib.com manuals search engine 54-I 18CHASSIS ELECTRICAL - HornHORN SWITCH
REMOVAL AND INSTALLATION(UP TO 1993 MODELS)
~
Y16FO207Removal steps
1. Air bag module (Refer to GROUP 528
(FROM 1994 MODELS)
- Air Bag Module and Clock Spring.)2. Horn contact switch3. Horn contact plate and wire4. Horn switchThe
horn switch is not supplied
If it is faulty, replace the steeringby itself.wheel assembly.i-.
-L 16FOO61200002400
RELAY
INSPECTION
HORN RELAY CHECK
Connect battery to terminal 1 and check continuity between
terminals with terminal 3 grounded.
~1
THEFT-ALARM HORN RELAY CHECK
Connect battery to terminal 2 and check continuity between
terminals with terminal 4 grounded.TSB Revision