1992 MITSUBISHI 3000GT air condition

Downloaded from www.Manualslib.com manuals search engine 16-12ENGINE ELECTRICAL - Charging System
GENERATORREMOVAL AND INSTALLATION
Pre-removal and Post-installation Operationl Removal and Installation of Right Bank Warm Up
Three-Way Catalytic Converter(Refer to GROUP 15-Exhaust Pipe, Main Mufflerand Catalytic Converter.)14-18ft.lbs.
l b
Removal steps
1. Air hose E 2. Air hose C
3. Suction hose clamo nuts
conditioning,4. Drive belt
(Refer to GROUP 11
-Engine Adjustment.)
216FO346
5. Generator connector
6. Heated oxygen sensor connector
7. Generator and generator bracket
assembly8. Generator bracket
9. Generator
lo-12 Nm7-9 ft.lbs.24 NmREMOVAL SERVICE POINT
dAbCLAMP NUT REMOVAL
On vehicles with an air conditioning, remove the clamp
nut, raise the suction hose and suspend it from the engine
hood using a cord.
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine ENGINE ELECTRICAL - Ignition System16-39
Wave-form Observation PointsPoint A: The height, length and
slope~of the spark line (refer to abnormal wave-form examples 1, 2, 3
and 4) show the following ‘trends.’\
Spark linePlug gapCondition of Compression Concentration
electrode
forceIgnition timing Sparkof air mixture
plug cable
LengthLongSmallNormal.
LowRichAdvancedLeak
ShortLarge
Large wear
HighLeanRetardedHigh
resistance
Height
HighLargeLarge wearHighLeanRetardedHigh
resistance
LowSmallNormal
Low
Rich _AdvancedLeak
SlopeLargePlug is fouled
-
Point B: Number of vibrations in reduction vibration section (Refer to abnormal wave-form example 5)
Point C: Number of vibrations at beginning of dwell section (Refer to abnormal wave-form example 5)
Point D: Ignition voltage height (distribution per each cylinder) shows the following trends.
Ignition
voltagePlug gapCondition of CompressionConcentration
electrodeIgnition timing Spark
forceof air mixtureplugcable
HighLarge
Large wearHighLean
RetardedHigh
resistance
LowSmallNormal
LowRich
AdvancedLeak
TSB Revision

Downloaded from www.Manualslib.com manuals search engine ENGINE ELECTRICAL - Ignition System16-43
Wave-form Observation Points/
LPoint A: The height, length and slope of the spark line (refer to abnormal wave-form examples 1, 2, 3and 4) show the following trends.
Spark linePlug gapCondition of CompressionConcentra-Ignition timing High tension
electrodeforcetion of air mix-cable
tureLength Long
SmallNormalLowRichAdvanced
Leak
Short
LargeLarge wearHighLeanRetardedHigh
resistanceHeight High
LargeLarge wearHighLeanRetardedHigh
resistance
LowSmall
NormalLowRichAdvancedLeak
SlopeLargePlug is fouled-
Point B: Number of vibrations in reduction vibration section
(Refer to abnormal wave-form example 5)
Number of vibrationsCoil and condenser
I3 or higher/ Normal
Except aboveAbnormal
Point C: Height of Zener voltage
Height of Zener voltageProbable cause
HigherProblem in Zener diode
LowerAbnormal resistance in pri-
mary coil circuit
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-1
CHASSIS
ELECTRICAL
CONTENTS
AERO PARTS (ACTIVE AERO).....Refer to GROUP 51
ANTI-LOCK BRAKING SYSTEM....
Refer to GROUP 35
BATTERY...........................................-3
ON-VEHICLE SERVICE............................3
Battery Charging.................................4Battery Inspection................................3Battery Testing Procedure........................5
SPECIFICATIONS................................-3
General Specifications............................3
CIGARETTE LIGHTER.............................119
CIGARETTE LIGHTER..........................123
SPECIFICATIONS..............................
119
General Specifications............I...........119
TROUBLESHOOTING............................120
COLUMN SWITCH.................................
.lll
COLUMN SWITCH*............................112
SPECIAL TOOL.................................111
SPECIFICATIONS...............................111
General Specifications..........................111
CRUISE CONTROL SYSTEM . . . . . . . Refer to GROUP 17
DOOR GLASS AND REGULATOR
(POWER WINDOWS) . . . . . . . . . . . . . .Refer to GROUP 42
DOOR HANDLE AND LATCH
(CENTRAL DOOR LOCKING) . . . . . . Refer to GROUP 42
DOOR MIRROR (ELECTRONIC
CONTROLLED MIRROR). . . . . . . . . . .Refer to GROUP 51
ELECTRONIC CONTROL
SUSPENSION . . . . . . . . . . . . . . . . . . . . Refer to GROUP
338
FRONT SEAT (POWER SEAT) . . . . Refer to GROUP 52A
HEATER AND AIR CONDITIONING . Refer to GROUP 55
HORN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
HORN SWITCH* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
RELAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
118
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
General Specifications . . . . . . . . . . . . . . . . . . . . . . . .115
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . .115
KEYLESS ENTRY SYSTEM
(CENTRAL DOOR LOCKING) . . . . . . Refer to GROUP 42
CONTINUED ON NEXT PAGE
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the
SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from render-
ing the SRS inoperative).
(2) Service or maintenance of any SRS component or
SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3)MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
TSupplemental Re-
straint System (SRS) and GROUP 00 -Maintenance Service before beginning any service or maintenance of any com-
ponent of the SRS or any
SRS-related component.
NOTE
The SRS includes the following components: impact sensors, SRS diagnosis unit, SRS warning light, air bag module, clock spring
and interconnecting wiring. Other SRS-related components (that may
h,a”” to be removed/installed in connection with SRS serviceor maintenance) are indicated in the table of contents by an asterisk ( ).

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Battery54-3
BATTERY
LSPECIFICATIONSGENERAL SPECIFICATIONS
ItemsUp to 1993 modelsFrom 1994 models
Type75D26R-MF75D23R-MF
Ampere hours
(5HR) Ah5252
Cranking rating [at -18°C (O’F)] A490520
Reserve capacity min.123118
NOTES
1.CRANKING RATING is the current a battery can deliver for 30 seconds and maintain a terminal voltage of
7.2 volts or greater at a specified temperature.
2.RESERVE CAPACITY RATING is the amount of time a battery can deliver 25A and maintain a minimum terminal
voltage of 10.5 at
27% (80°F).
L
16FO123
White
Blue
ChargingGood
necessaryconditionON-VEHICLE
SERVICE
BATTERY INSPECTION
BAlTERY VISUAL CHECK (1)
The battery contains a visual test indicator which gives blue
signal when an adequate charge level exists, and white signal
when charging is required.
BAlTERY VISUAL CHECK (2)
Make sure ignition switch is in Off position and all battery
feed accessories are Off.
1.Disconnect ground cable from battery before disconnecting
(+) cable.
2. Remove battery from vehicle.
CautionCare should be taken in the event battery case is
cracked or leaking to protect hands from the electro-
lyte. A suitable pair of rubber gloves (not the house-hold type) should be worn when removing battery
by hand.
3.Inspect battery carrier for damage caused by loss of acid
from battery. If acid damage is present, it will be necessaryto clean area with a solution of clean warm water and
baking soda. Scrub area with a stiff bristle brush and wipe
off with a cloth moistened with ammonia or baking soda
in water.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-164CHASSIS ELECTRICAL - Radio and Tape Player
A-6There is noise when starting the engine.
Noise type
Sounds are in pa-
rentheses ( ).
AM, FM:
Ignition noise
(Popping, Snap-
ping,Cracking,
Buzzing)
Otherelectrical
components
Static electricity
(Cracking, Crin-
kling)
Conditions
0Increasing the engine speedcausing the popping sound tospeed up, and volume de-creases.0Disappears when the ignitionswitch is turned to ACC.
-
lDisappears when the vehicle is
completely stopped.Occurs when parts or wir-
Severe when the clutch is en-ing move for some reasonlgaged.and contact metal parts of
the body.
lVarious noises are produced de-pending on the body part of thevehicle.
Due to detachment from
the body of the front hood,
bumpers, exhaust pipe
and muffler, suspension,
etc.
Causel
Mainly due to the
spark plugs.l Due to the enginenoise.
Noise may appear as
electrical components be-
come older.
Parts to be Location of
inspectedparts
or remedy(next page)
Noise con- 1
denser
Ground
cable2, 3
Repair or replace electricalcomponents.
Return parts or wiring to
their proper position.
Caution
1.Connecting a high tension cable to the noise
filter may destroy the noise filter and shouldnever be done.
2.Check that there is no external noise. Since
failure to do this may result in misdiagnosis
due to inability to identify the noise source,
this operation must be performed.3. Noise prevention should be performed by
suppressing strong sources of noise step
by step.
NOTE
1. Condenser
The condenser does not pass D.C. current, butas the number of waves increases when it
passes A.C. current, impedance (resistanceagainst A.C.) decreases, and current flow is
facilitated. A noise suppressing condenser
which takes advantage of this property is in-
serted between the power line for the noise
source and the ground. This suppresses noiseby grounding the noise component (A.C. or
pulse signal) to the body of the vehicle.
2. Coil
The coil passes D.C. current, but impedance
rises as the number of waves increases relativeto the A.C. current. A noise suppressing coil
which takes advantage of this property is in-
serted into the power line for the noise source,
and works by preventing the noise componentfrom flowing or radiating out of the line.
1 TSB Revision
Ground parts by bonding.
Cases where the problem
is not eliminated by a single
response to one area are
common, due to several
bodypartsbeing
imperfectly grounded.

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Player54-167
A-8Noise sometimes appears on FM during traveling.
NoIs the antenna completely extended?
Yes
t Check the antenna itself.
(Refer to E-l, 2.)
+Does the problem clear up whenre
1 No
Yes
iDoes the problem appear only in certain locations and only with yes
certain stations?
No
~ Due to electrical field conditions. (Multipath
noise*, fading noise*).
Are connectors property connected?
Yes
Check connector connections.1
tDoes noise appear when the radio switch is turned on while the
vehicle is stopped
and the radio is struck while tuned away froma station?
Yes
No*Static electricity noise:Sody static electric from the shock absorberrubber bushings used to prevent vibration, tires,etc. occurs because of separation from the
ground, causing a buzzing noise.
Since no measures can be taken on the radioside, steps should be taken to discharge the
static
electricitv of the vehicle bodv.
Is the radio body correctly grounded?
No(Is the mounting screw tightened securely?
)
Yes
-) Tighten the screw securely.I
Is the antenna correctly grounded? (If noise appears when the antennais moved, this means the ground is not securely connected.)
Yes
If rust is present on the antenna ground screw,clean and tighten the ground securely.
*
1 Repair or replace radio.1
About multipath noise and fading noise
Because the frequency of FM waves is extreme-
ly high, it is highly susceptible to effects from
geological formations and buildings. These ef-
fects disrupt the broadcast signal and obstruct
‘reception in several ways.l Multipath noise
This describes the echo that occurs when the
broadcast signal is reflected by a large obstruc-
tion and enters the receiver with a slight time
delay relative to the direct signal (repetitious
buzzing).l Fading noise
This is a buzzing noise that occurs when the
broadcast beam is disrupted by obstructing ob-
jects and the signal strength fluctuates intricately
within a narrow range.
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-168CHASSIS ELECTRICAL - Radio and Tape Player
IA-9Ever-present noise.I
Noise is often created by the following factors, and
often the radio is OK when it is checked individually.l Traveling conditions of the vehicle
l Terrain of area traveled through
l Surrounding buildings
l Signal conditions
l Time periodFor this reason, if there are still problems with noiseeven after the measures described in steps A-l
to A-8 have been taken, get information on the fac-
tors listed above as well as determining whetherthe problem occurs with AM or FM, the station
names, frequencies, etc., and contact a service cen-
ter.B. RADIO
IB-lNo power is supplied when the switch is set to ON.IIIIs multi-purpose fuse No. 4 blown or is the circuit open?Replace fuse or repair harness.
NoIs the connector at the back of the radio connected properly?
Yes
Connect connector securely.1t
NoDisconnect and check the connector at the rear of the radio. Is the ACC / Repair harness.
power (12 V) being supplied to the radio?J
I
Yes
1 Reoair or reolace radio.
1 B-2No sound from one speaker.ICheck to see if there is any sound when attached
to another radio.
I-=----[Repair or replace radio unit.
No
checkthespeakerharnessfor conductance.
out.*Speakarj
NoRepair speaker harness and ensure
proper connection of relay connectors.
tRepair or replace speaker.
1 TSB Revision