1992 MAZDA PROTEGE battery

I
EXTERIOR LIGHTING SYSTEM
TNS system (side marker, license, tail, illumination
light) does not operate
I
Turn ON light switch
I
Check tail 15A fuse
I OK
Confirm battery voltage on W/B wire of TNS relay
connector Repair harness (Main fuse - TNS relay)
I OK
Check TNS relay (Refer to page T-42) Replace the TNS relay OK
Confirm battery voltage on L/G wire of the combination NG
switch Repair harness (TNS relay - Combination switch)
I OK
Confirm battery voltage on RIB wire of front and rear
side marker, license, tail, and illumination light
connectors Repair harness (TNS relay - Lights)
I OK
Confirm continuity on B wire of above connectors to
ground NO
- Repair harness (Lights - Body ground)
Replace the bulbs
I
23UOTX-022
T-38

I
EXTERIOR LIGHTING SYSTEM
Both stoplights do not operate when brake pedal is
depressed
i
Check stop 20A fuse
I Short circuit
Confirm battery voltage on G/W wire of the stoplight
switch
I Repair harness (Fuse - Stoplight switch) OK
Check the voltage with the brake pedal depressed
I
BD
c
Confirm battery voltage on G Replace the stoplight switch
8) OK
Confirm battery voltage on G Repair harness (Stoplight switch - Stoplight)
(B
Confirm continuity on B wir Repair harness (Stoplight - Body ground)
I I I
I
Replace the bulb
I
23UOTX-023 One stoplight does not come on
Burnt out bulb or faulty grounding
03UOTX-058
T-40

EXTERIOR LIGHTING SYSTEM
Inspection
Headlight (Headlight relay)
1. Disconnect the headlight relay connector and remove the
relay.
2. Check for continuity between terminals of the relay.
d b
23UOTX-024
C a
~
d b C
a
iYiFz3l
23UOTX-02
C a
~
d b
23UOTX-026 C
a
a
d b Qec a
I I h f d
03UOTX-063 ve: Battery voltage
Connecting to
a b c d
v0 Ground
- -
0 0
a b 0 0
o--<>: Indicates continuity
Headlight (DRL relay)
1, Disconnect the DRL relay connector and remove the relay.
2. Check for continuity between terminals of the relay.
VB: Batterv voltaae
Connecting t- n a b C d
Ve Ground
- -
C-3 I 0
r-- a b
o---O: Indicates continuity 0 1 0
Front combination light (TNS relay)
1. Disconnect the TNS relay connector and remove the relay.
2. Check for continuity between terminals of the relay.
VB: Batterv voltawe
Connecting to
a b C d VB Ground
-
0 0
I a b
O-4: Indicates continuity 0 1 0 1
Front combination light (Flasher unit)
1. Check for continuity between terminals of the flasher unit.
a-g
a-h
c-a
c-d
c-e
c-f
r--n
t------ X
e-a X
g-d X
X e-c X
g-e X
0 e-d X
g---f X
0 e-f X
P-h X
0
e-g X h-a 0
0 e-h X h-c 0
I ” Y
C-h
d-a
C
I
x 1 h-d 1 n I 0 f-a
0 f-c X h-e 0
X f-d X h-f 0
X f-e X
h-g 0
F d-
0: Indicates continuity X: No continuity
T-42

INTERIOR LAMP SYSTEM T
IG key illumination does not operate
Check room IOA fuse NG
- Short circuit
0 OK
Confirm battery voltage on V Defective harness (Fuse - Joint box), or bulb
0 OK
Confirm continuity on B wire of the joint box (CPU) to
ground Repair harness (Joint box - Body ground)
OK
When any door is opened, confirm that interior lamp
comes on
OK NG
~ Defective harness (Joint box - Door switch), or door
switch
Confirm continuity between N terminal of JB-09 connec- _ NG
-
tor and B terminal of JB-03 connector Repair harness (JB-09 - JB-03)
I OK
Replace CPU
23UOTX-029
Inspection
Door switch (Front sides with passive belt)
Confirm continuity between the R/W wire and the B wire of
the door switch connector (in passive motor connector).
Condition Continuity
Push X
Not push 0
0: Indicates continuity X: No continuity
03UOTX-181 Door switch (Others)
Confirm for continuity between the terminals of the door switch.
Condition Continuity
Push X
Not push 0
0: Indicates continuity X: No continuity
1 I OSJOTX-082
T-51

CENTRAL PROCESSING UNIT (CPU) T
Inspection
1. Remove the CPU and check the voltage or continuity between terminals of joint box and a body ground.
Ve: Battery voltage
Terminal
A Connected to Test condition Specification
B Rear wiper motor Ignition switch
Va
Light switch ON (first and second position) V0
C TNS switch
Light switch OFF ov
Seat belt buckled Ofi
D Seat belt buckle switch
Seat belt unbuckled
co
E
Rear wiper switch ON
OCI
F
Rear wiper switch
Rear wiper switch OFF
co
Rear washer switch ON 00
G Rear washer switch
Rear washer switch OFF
00
H
Key reminder switch ON
Va
I Key reminder switch
Key reminder switch OFF
ov
Ignition switch OFF ov
J Seat belt warning lamp
Ignition switch ON
VB
K Ground Constant
ov
L IG key illumination Constant
VB
For 5 seconds after ign. switch ON and belt unbuckled
00
M Passive shoulder belt
Other conditions
00
All doors closed
Va
N Door switch
Any door open
ov
0 Battery Constant VB
P Ignition switch
ignition switch ON V0
23UOTX-031
T-57

T WARNING SYSTEM
WARNING SYSTEM
WARNING BUZZER AND TIMER
Circuit Diagram
WARNING LAMP
REAR WIPER SW
RASSIVE CONTROL UNIT
Inspection
Remove the CPU and check the voltage or continuity between terminals of joint box and a body ground.
Key reminder alarm does not sound.
VB: Battery voltage
Terminal Connected to Test condition Specification To correct
I
Key reminder switch Key in cylinder VB Check ignition switch and
(ignition switch) Key out bf cylinder ov wiring harness
(Refer to page T-21)
P Ignition switch Ignition switch ON
‘/B Check ignition switch and
wiring harness
(Refer to page T-21)
N Door switch Any door open ov Check door switches and
All doors closed VS wiring harness
(Refer to page T-51)
23UOTX-031
T-58

WARNING SYSTEM
Light-off reminder alarm does not sound.
VB: Battery voltage
Terminal Connected to Test condition Specification To correct
C Headlight switch Headlight switch ON VB Check headlight switch and
wiring harness
(Refer to pages T-27, 28)
P Ignition switch Ignition switch ON VB Check ignition switch and
wiring harness
(Refer to page T-21)
N Door switch Any door open ov Check door switches and
All doors closed V0 wiring harness
(Refer to page T-51)
23UOTX-033
Seat belt alarm does not sound.
VB: Battery voltage
Terminal Connected to Test condition Specification To correct
P ignition switch Ignition switch ON
Vs Check ignition switch and
wiring harness
(Refer to page T-21)
D Seat belt buckle switch Seat belt buckled
00 Check seat belt buckle switch
Seat belt unbuckled
00 and wiring harness
(Refer to page S-102)
23UOTX-034
Seat belt timer does not operate.
VB: Battery voltage
Terminal Connected to Test condition Specification To correct
P Ignition switch Ignition switch ON VE Check ignition switch and
wiring harness
(Refer to page T-21)
23UOTX-035
Passive shoulder belt alarm does not sound.
VB: Battery voltage
Connected to Test condition
Ignition switch Ignition switch Specification
VB
Passive shoulder belt
control unit For 5 seconds after
ignition switch and belt
unbuckled
Other conditions 00
co
IG key illumination timer does not operate.
To correct
I
Check ignition switch and
wiring harness
(Refer to page T-21)
Check passive shoulder belt
control unit and wiring harness
(Refer to page S-104)
23UOTX-036
Ve: Battery voltage
Terminal Connected to Test condition Specification To correct
L IG key illumination Either door open
VB Check bulbs and wiring
harness
N Door switch Any door open ov Check door switches and
All doors closed
VB wiring harness
(Refer to page T-51)
23UOTX-037
T-59

2L BUZZER 2A 28 2C 2D 1A 3K l--r nnmn
I I‘ I
1C 3L 2E 2G IL iG 1F 1D tB
3F 38 3G 1E 3D
l-l rt
II l-l
l-l It II l-l 1J 11 1H
1G IF 1E 1D 1C 1B 1A 2L 2K 2J 21 2H 2G 2F 2E 2D 2C 28 2A
r-l It ,I 3L 3K 3J 31 3H 3G 3F 3E 3D 3C 3B 3A
Ter- I I minal Connected to 1 1A Combination switch
1B Ground
IC Fuel tank unit
1 ID 1 EGI control unit
I
II L 1J 1
L Ter-
minal Connected to
2A Speed sensor output
28 Light switch (high beam)
2C Turn switch (L)
20 Turn switch (R)
2E Ground
2F Ground
2L 1 IGI battery Ter-
minal Connected to
3A
38 Alternator
3c
30 Oil pressure switch
3E
3F Parking brake switch, Brake fluid switch
3G Passive shoulder belt control unit
3H h
I 31
3J
3K
IG2 battery
3L Water temperature gauge unit