1992 MAZDA PROTEGE water pump

B2 ON-VEHICLE MAINTENANCE
TIMING BELT
Removal / Installation
1. Disconnect the negative battery cable.
2. Raise the vehicle on a lift and remove the right front wheel.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Install in the reverse order of removal, referring to Installation Note.
/ 7.8-11 N.m
(80-l 10 Cm-kg, 69-95 in-lb
1p1\ ’ (3.8-6.3, 2738)
, (80-l 10 cm-kg, 69-95 in-lb)
167--187 (X-17, 116-123)
/ 7.8--11 N-m
(80-110 MI-kg,
7.8-11 N-m
\-
(80-110 Cm-kg, 69-95 in-lb)

12-17 (1.25-1.75, 9-13)
N-m (m-kg, &lb
23UOl32-0
1. Under cover and side cover 11. Timing belt cover, lower
2. P/S and/or A/C drive belt 12. Pulley lock bolt
3. Alternator drive belt Removal Note . . ..*..........*.*......... page 82-13
4. Water pump pulley Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page B2-14
5. Plate 13. Pulley boss
6. Crankshaft pully 14. Timing belt
7. Spark plugs Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page 62-13
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page 62-15 Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page B2-14
8. Oil dip stick 15. Tensioner and tensioner spring ..l
9. Timing belt cover, upper Installation Note ..,..................... page B2-14
10. Timing belt cover, middle 16. Idler
B2-12

ON-VEHICLE MAINTENANCE B2
1. Under cover and side cover
2. Resonance chamber
3. Air hose
4. Accelerator cable
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page B2-21
5. Throttle cable (ATX)
Removal I Installation . . . . . . . . . . . . . . . . . . . . . Section K
6. High-tension lead
7. Hoses
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . below
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page 82-21
8. Harnesses
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page B2-18
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page 82-21
9. Water bypass pipe
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page B2-18
10. P/S and/or A/C drive belt
Removal / Installation . . . . . . . . . . . . . . . . page B2- 6
11. Alternator drive belt
Removal / Installation . . . . . . . . . . . . . . . . page B2- 6 12. Water pump pulley
13. Timing belt cover, upper
14. Timing belt cover, middle
15. Spark plug
16. Timing belt
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page 82-l 8
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page B2-20
17. Front exhaust pipe
18. Intake manifold bracket
19. Cylinder head cover
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page 82-19
20. Cylinder head bolt
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page B2-19
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page B2-19
21. Cylinder head
Disassembly . . . . . . . . . . . , . . . . . . . . . . . . . page B2-45
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B2-54
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 82-79
22. Cylinder head gasket
23UOB2-021
Removal / Installation note
Hoses
1. Disconnect the hoses shown in the figure.
VACUUM HOSE BRAYE VACUUM HOSE
‘-;:I::------. CAUT’oN
l COVER THE HOSE WITH A RAG BECAUSE FUEL WILL
SPRAY OUT WHEN DISCONNECTING.
- PLUG THE DISCONNECTED HOSES TO AVO!D FUEL
LEAKAGE.
OWOBX-03
82-l i

B2 ON-VEHICLE MAINTENANCE
HLA
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. install in the reverse order of removal, referring to Installation Note --- ----- -__ __-- ,‘.
11.3-14.2 N.m
(1.15-1.45 m-\g, 100-126 in-lb)
49-61
(5.0~6.2,-36-45)
4.9-6.6 N.m
(50-90 cm-kg, 43-76 in-lb)
7.6All N-m
(80-110 cm-kg, 69-95 in-lb) 1 Q’-25
(1.9-2.6, 14-19)
N.m (m-kg, ft-lb)
0311082-03
1. High-tension lead
10. Cylinder head cover
2. Distributor
Installation Note..
....................
Installation Note.. ......................
page 62-25
11. Camshaft pulley
3. P/S and/or A/C drive belt
Removal note ..........................
Removal / Installation..
.............. page E32-
6
Installation Note .......................
4. Alternator drive belt
12. Seal plate
Removal / Installation
......... . ...... page B2- 6
13. Camshaft
5. Water pump pulley
Removal Note.. ........................
6. Timing belt cover, upper
Installation Note.. .....................
7. Timing belt cover, middle
14. HLA
8. Spark plug
Removal note ..........................
9. Timing belt
Installation
Note.. .....................
Removal Note.. .........................
page B2-18 Inspection
................................
Installation Note.. ......................
page B2-20
7
page 62-19
page 82-23
page 82-24
page B2-23
page 62-23
page B2-23
page B2-23 ‘--’
page 82-60
82-22

DISASSEMBLY 82
TIMING BELT
1. Disassemble in the order shown in the figure, referring to Disassembly Note.
23UOB2-0:
1. Water pump pulley
2. Crankshaft pulley
3. Timing belt cover, upper
4. Timing belt cover, middle
5. Timing belt cover, lower
6. Pulley lock bolt
7. Pulley boss
8. Timing belt
Disassembly Note . . . . . . . . . . . . . . . . . . . . page B2-44
9. Tensioner and tensioner spring
10. Idler
Disassembly Note . . . . . . . . . . . . . . . . . . . . page B2-44
B2-43

B2 DISASSEMBLY
CYLINDER BLOCK (EXTERNAL PARTS)
1. Disassemble in the order shown in the figure, referring to Disassembly Note.
I
@ma @a% GASST, REPLACE
GASKET,
REPLACE
/
d I @REPLACE
23UOB2-0
1. Water pump
Service ..,....,..,......,.,.,,.....,,.,.......... Section E
2. Timing belt pulley and lock bolt
Disassembly Note . . . . . ..,.,........,. page 82-49
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 82-65
3. Clutch cover, clutch disc (MTX)
Service . . . , , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section H
4. Flywheel (MTX)
Disassembly Note ,.. . . . . . . . . . . . . . . . . . page 82-49
Inspect for wear or damage
5. Backing plate, drive plate, and adapter (ATX)
Disassembly Note . . . . ,., ,..... . . . . . . . page B2-49
6. End plate 7. Oil pan and gasket
Disassembly Note .,.................. page 82-49
Inspect for damage
8. Oil strainer
9. Main bearing support plate (MBSP)
Disassembly Note . . . ., . . . . . ..,.... . . . page B2-50
Inspect for damage
10. Oil pump
Service . . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section D
11. Front oil seal
Disassembly Note .,.................. page 82-50
12. Rear cover
13. Rear oil seal
Disassembly Note . . . . . . . . . . . . . . . . . . . . page B2-50
B2--48

I32 ASSEMBLY
Qill’ ’ 23UOB2-050
03UOB2-10
2. Install the timing belt pulley.
3. install the pulley Woodruff key with the tapered side toward
the oil pump body.
4. Install the pulley lock bolt.
5. Tighten the pulley lock bolt.
Tightening torque:
157-167 N#rn (16-17 m-kg, 116-123 ft-lb)
Water Pump
1. Remove all foreign material from the water pump mount-
ing surface.
2. Install the water pump and a new gasket.
Tightening torque:
19-25 N.m (1.9-2.6 m-kg, 14-19 ft-lb)
82-78

I 23UOB2-044
82 ASSEMBLY
DEFLECTION CHECKING POlNT
--; 11. Measure the timing belt deflection by applying moderate
oressure (98 N, 10 kg, 22 lb) midway between the two cam-
shaft pulleys.
If the deflection is not correct, repeat from Step 7 above.
Deflection:
9.0-11.5mm (0.35-0.45 in) at 98 N (10 kg, 22 lb)
Timing Belt Cover
1. Install the lower, middle, and upper covers.
Tightening torque:
7.8-11 N.m (80- ,110 cm-kg, 69-95 in-lb)
I 13EOB2-037
82-86
Pulley lock bolt
1. Hold the flywheel (MIX) or drive plate (ATX) with the SST
and tighten the pulley lock bolt.
Tlghtening torque:
157-167 N.m (16-17 m-kg, 116-123 ft-lb)
Cankshaft pully
1. Install the crankshaft pulley.
2. Install the plate.
3. Tighten the pulley bolts.
Tightening torque:
12-17 N-m (1.25-l -75 m-kg, 9-13 ft-lb)
Water Pump Pulley
1. Install the water pump pulley.
Tightening torque:
7.8-11 N*m (80-110 cm-kg, 69-95 in-lb)

E
COOLING SYSTEM
INDEX ...................................................... E- 2
OUTLINE .................................................. E- 4
SPECIFICATIONS .................................... E- 4
TROUBLESHOOTING GUIDE ...................... E- 4
ENGINE COOLANT .................................... E- 5
PREPARATION ....................................... E- 5
INSPECTION ..........................................
REPLACEMENT ...................................... :z ;
RADIATOR CAP ........................................
PREPARATION ....................................... ;I ;
INSPECTION .......................................... E- 7
RADIATOR ............................................... E- 8
REMOVAL / INSTALLATION ...................... E- 8
INSPECTION .......................................... E- 9
THERMOSTAT .......................................... E- 9
REMOVAL / INSTALLATION ...................... E- 9
INSPECTION .......................................... E- 9
WATER PUMP .......................................... E-l 1
REMOVAL / INSTALLATION ...................... E-l 1
ELECTRIC COOLING FAN SYSTEM ............ E-13
SYSTEM CIRCUIT .................................... E-l 3
SYSTEM INSPECTION .............................. E-14
FAN MOTOR ............................................. E-14
INSPECTION .......................................... E-l 4
REPLACEMENT ...................................... E-l 5
WATER THERMOSWITCH .......................... E-l 8
REMOVAL / INSTALLATION ...................... E-18
INSPECTION .......................................... E-l 8
RADIATOR THERMOSWITCH ..................... E-l 7
REMOVAL I INSTALLATION ...................... E-17
INSPECTION .......................................... E-l 7
FAN RELAY .............................................. E-l 8
REMOVAL I INSPECTION .......................... E-l 8
INSPECTION .......................................... E-l 8
23UOEX-001