1992 MAZDA PROTEGE torque

TRANSAXLE 52
r
03UOJ2-09:
03UOJ2-09
03UOJ2-094
03UOJ2-09!
03UOJ2-09t
fith/Reverse shift rod end, Sth/Reverse shift rod and clip
Note
l The mark (indicated by the arrow in the figure) and
the shift rod end mounting bolt hole must be in the
same direction.
1. Install the shift rod end @ and the shift rod 0, and tighten
the gate mounting bolt.
Reverse idler gear and reverse idler shaft
1. install the reverse idler gear and the reverse idler shaft.
2. Attach the magnet to the clutch housing.
3. Align the end of the interlock sleeve with the control lever
(indicated by the arrow), and, at the same time, face the
reverse idler shaft screw hole in the direction shown in the
figure.
Clutch housing and transaxle case assembly
1. Apply a thin coat of sealant to the contact surfaces of the
clutch housing and transaxle case, tighten the transaxle case
installation bolts to the specified torque.
Tlghtenlng torque:
37-52 Nsrn (3.8-5.3 m-kg, 27-38 ft-lb)
2. Insert the SST through driveshaft hole.
Secondary 5th gear
1. Install the secondary 5th gear as shown.
Clutch hub assembly (Sth/Reverse) and !%h/Reverse shift
fork
1. Install the clutch hub assembly (5thReverse) and the 5th/Re-
verse shift fork together.
52-39

52 TRANSAXLE
23UOJ2-01:
Locknut
1. Shift to 1 st gear.
2. Lock the primary shaft with the
SST.
3. Tighten new locknuts on the primary and secondary shafts.
Tightening torque:
128-198 N&m (13.0-20.0 m-kg, 94-145 ft-lb)
4. Stake the locknuts.
5. Measure the 5th gear thrust clearance with a dial indicator.
Clearance: 0.1 O-0.22mm (0.0039-0.0087 in)
Maximum: 0.27mm (0.011 in)
6. If not as specified, reassemble the transaxle.
52-40

SHIFT MECHANISM
1. Change lever knob
2. Rear console
3. Front console
4. Boot
5. Nut
6. Washer
7. Bolt
8. Cover
9. Nut
10. Washer
11. Bushing
12. Spring
Inspect for damage and weaked
Assembly note . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-47
13. Change lever
14. Ball seat (Upper)
15. Boot
Inspect for wear or damage 16. Holder
17. Ball seat (lower)
18. Nut
19. Washer
20. Pipe
21. Bushing
Inspect for wear or damage
22. Washer
23. Extension bar
Assembly note . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-47
24. Insulator
Inspect for damage and cracks
25. Nut
26. Bolt
27. Bushing
Inspect for wear and damage
28. Change control rod
Inspect for bending
03UOJ2-109
CHAGE CONT
03UOJ2-111
Assembly Note
Extension bar
1. Connect the extension bar to the transaxle, and then mount
it to the floor.
Tightening torque:
16-23 N+m (1.6-2.3 m-kg, 12-17 ft-lb)
Spring
1. Verify that the hooked part of the spring is properly seated
in the bracket groove.
J2-47

FRONT AXLE M
WHEEL HUB, STEERING KNUCKLE
Preinspection
Wheel bearing play
1. Remove the wheel and tire.
2. Remove the brake caliper assembly and disc plate.
3. Position a dial indicator against the wheel hub. Push and
pull the wheel hub by hand in the axial direction and meas-
ure the wheel bearing play.
4. If the bearing play exceeds specification, check and adjust
the locknut torque or replace the wheel bearing if necessary.
Removal / Installation
d Maximum wheel bearing play: 0.05mm (0.002 in)
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to
Installation Note.
4. After installation, check the front wheel alignment. (Refer to Section R.)
SERVIC\E, SECTION R

7 93--12? W.-L%” COTiER PIN, REPLACE
(9.5-12.9, 69-S
39-54
(4.0-5.6, 29-40) 39-64 ’ 236-319 (24.0-32.5, 174-235)
(4.4-6.0, 32-43)
66-67)
N.m (m-kg, it-lb)
23UOMX-006
1. Wheel and tire
2. Locknut
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M- 6
3. Brake caliper assembly
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P
4. Disc plate
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P
5. Tie rod end
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . page M- 6
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M- 6 6. Lower ball joint
7. Knuckle, wheel hub, and dust cover
Inspect wheel hub for cracks and damage
Inspect knuckle spindle for cracks and
damage
Inspect dust cover for damage and dis-
tortion
Disassembly / Inspection I
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page M- 7
M-5

M FRONT AXLE
23UOMX-0:
Removal note
Tie rod end
Caution
l Do not damage the dust boot.
1. Loosen the nut and disconnect the tie-rod end with the SST.
Installation note
Tie rod end
Caution
l Do not damage the dust boot.
1. Install the nut and secure it with the new cotter pin.
Tightening torque:
42-57 N-m (4.3-5.8 m-kg, 31-42 ft-lb)
Locknut
1, Install a new locknut and stake it, as shown.
Tightening torque:
235-319 Nnrn (24.0-32.5 m-kg, 174-235 ft-lb)
03UOMX-010
M-6

REAR AXLE M
L.3”“I”lh-” I
Removal / Inspection / Installation
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to
Installation Note.
4. After installation, bleed the brake system, adjust the parking brake lever stroke (Refer to Section P.) and
DRUM BRAKE TYPE
Preinspection
Wheel bearing play
1. Remove the wheel and tire.
2. Position a dial indicator against the brake drum. Push and
pull the rear brake assembly by hand in the axial direction
and measure the wheel bearing play.
3. If the bearing play exceeds specification, check and adjust
the locknut torque or replace the wheel bearing if necessary.
Maximum wheel bearing play: 0.05mm (0.002 in)
66-l 17 (6.7-l 1.9, 63-66)
45-59
(4.6:6.0, 33-43)
check the rear wheel alignment (Refer to Section R.)
SEiWICE, SECTION R /
I
GA
19-26 (1.9-2.6, 14-19)
177-235
(16.0-24.0, 130-174) d
REPLACE REPLACE
(9.0-12.0,
65-67)
N.m (m-kg, ft-lb)
7RI ImAX-ni
J 3
1. Wheel and tire
2. Hub cap
3. Locknut
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-l 2
4. Brake drum
5. Hub bearing assembly
Inspect for cracks and damage
Disassembly I Assembly . . . . . . . . . . . . page M-l 3 6. Parking brake cable
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P
7. Brake pipe
Removal Note .,.......................... page M-12
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-l 2
8. Rear brake assembly
Service ,,........................................ Section P
9. Rear spindle
Inspect for cracks and damage
M-l 1

M REAR AXLE
!O
03UOMX-01 0
0.5mm
19
Removal note
Brake pipe
Caution
l After disconnecting the brake pipe, plug it to avoid
fluid leakage.
1. Disconnect the brake pipe with the SST.
lnstallatlon note
Brake pipe
1. Tighten the brake pipe with the SST.
Tightening torque:
13-22 N*m (1.3-2.2 m-kg, 9.4-16 ft-lb)
Locknut
1. Install a new locknut and stake it, as shown.
Tightening torque:
177-236 Narn (16-24 m-kg, 130-l 74 ft-lb)
M-12

M REAR AXLE
DISC BRAKE TYPE
Preinspection
Wheel bearing play
1. Remove the wheel and tire.
2. Remove the brake caliper assembly.
3. Position a dial indicator against the wheel hub. Push and
pull the wheel hub by hand in the axial direction and meas-
ure the wheel bearing play.
4. If the bearing play exceeds specification, check and adjust
the locknut torque or replace the wheel bearing if necessary.
-I 5 Maximum wheel bearing play: 0.05mm (0.002 in)
Removal / Inspection / Installation
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to
Installation Note.
4. After installation. check the rear wheel alianment (Refer to Section R.)
45-61
(4.6-6.2, 33-45)
-118
-12.0,
-87)
REPLACE
16-23
(1.6-2.3, 12-17)
N-m (m-kg, ft-lb]
311 InMY-nif4
1. Wheel and tire
2. Hub cap
3. Locknut
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-15
4. Brake caliper assembly
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..~ Section P
5. Disc plate
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P 6. Hub bearing assembly
Inspect for cracks and damage
Disassembly I Assembly . . . . . . . . . . . . page M-l 5
7. Dust cover
8. Rear spindle
Inspect for cracks and damage
M-14