1992 MAZDA PROTEGE belt

HEADLINER S
HATCHBACK
(WITH
PASSIVE SHOULDER BELT)
I
R.H. SIDE I
1. Assist handle 5. Rearview mirror
2. Interior lamp 6. Headliner
3. Sunvisor Removal Note .,.,,.,,.......*........,.*.* page S-93
4. Sunvisor adapter
Installation Note ..,.............*......... page S-93
s-91

s HEADLINER
HATCHBACK
(WITHOUT PASSIVE SHOULDER BELT)
R.H. SIDE
1. Assist handle
2. Interior lamp
3. Seaming welt (With sliding sunroof)
4. Sunvisor
5. Sunvisor adapter
6. Rearview mirror
13uosx-03
7. Overhead console (With sliding sunroof)
8. Seaming welt (Pillar)
9. Headliner
Removal Note ,..........,,,....,..,....... page S-93
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . . page S-93
10. Front top bracket ---
S-92

HEADLINER S
iATCHE3ACK
A
3EC.A-A: WITHOUT PASSIVE SHOULDER BELT
03uosx-17
Removal Note
Headliner
The headliner is bonded to the front (or rear) top bracket with
the double adhesive tape as shown. (Except hatchback with
passive shoulder belt.)
Caution
l Peel off the bonded section of the headliner care-
fully to prevent damaging it.
Installation Note
Headliner
1. Install the headliner using the body brackets (hatchback)
and fasteners.
2. Install the seaming welt between the front top bracket and
the body to hold the headliner.
s-93

DASHBOARD S
1, Rear ashtray (Without passive IO. Combination switch 18. Glove box lid
shoulder belt) Removal / Installation 19. Lower panel (R.H.)
2. Rear console ,..,,.,......,,.,.,....... Section T 20. Front ashtray
3. Front console 11. Center upper hole cover 21. Lower panel (Center)
4. Control box center cover 12. Upper garnish
22. Glove box cover
(With small front console) 13. Side panel 23. Dash board
5. Side walls 14. Hood release knob Removal Note . . page S-95
6. Undercover 15. Lower panel (L.H.) Installation Note page S-96
7. Steering column 16. Meter hood 24. Pipe frame (Lower)
Removal / Installation 17. Instrument cluster 25. Pipe frame (Upper)
. . . . . . . . ...*. . . . . ..n..... Section N Removal I Installation
1 suosx-017
8. Key cylinder set ring
9. Column cover
JOINT BOX
. . . . . . . . . . . . . . . . . . . . . . . . . . Section T
Removal Note
Dashboard
1, Remove the control wires of the heater unit and blower unit.
2. Disconnect the necessary harness connectors.
s-95

TRIM
TRIM
COMPONENTS
Removal / Installation
1, Remove in the order shown in the figure.
2. install in the reverse order of removal.
Note (PROTEGE)
l Remove the front seat belt upper anchor for removal of the B-pillar upper trim.
(Refer to page S-100.)
l Remove the rear seat side cushion (or seat back) and the rear seat belt upper anchor for removal
of the C-pillar trim. (Refer to pages S-l 01, 111.)
l Remove the high-mount stopllght (Interior mounted ) for removal of the rear package trlm.
(Refer to Section T.)
PROTEGe
WITH PASSIVE SHOULDER BELT
Q
8
I I
, -- ,, , ,--.
*.I r---i ‘Y’ L--d I ST
I
1RI insx-ni
1. Front side trim
2. Scuff plate
3. A-pillar trim
4. B-pillar lower trim
5. B-pillar upper trim
(Without passive shoulder
belt) 6. Front door trim 8. Rear header trim
Removal I Installation 9. C-pillar trim
. . . . . . . . . . . . . . . . . . . . . . . page S-l 1 10. Rear package trim
7. Rear door trim 11. Rear package edge trim
Removal / Installation 12. Trunk end trim
,.,.................... page S-l 7 13. Trunk side trim
s-97

S TRIM
Note (Hatchback)
l Remove the front seat belt upper anchor for removal of the B-pillar upper trim.
(Refer to page S-100.)
l Remove the rear seat belt upper anchor and the quarter window lock for removal of the C-
pillar trim. (Refer to pages S-62, 101.)
l Remove the rear seat cushion for removal of the quarter trim. (Refer to page S-112.)
* Disconnect the negative battery cable for removal of the rear hatch lower trim. (With luggage
compartment lamp.)
iATCHBACK
'. .' LA I i-i I / '.
1. Front side trim 7. Quarter trim
2. Scuff plate 8. B-pillar upper trim
3. Front door trim (Without passive shoulder belt)
Removal I Installation . . . . . . . . . . page S-l 0 9. A-pillar trim
4. Trunk end trim 10. Rear header trim
5. Trunk side cover 11. C-pillar trim
6. Trunk side trim 12. Rear hatch lower trim
S-98

FLOORMAT S
FLOORMAT
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. To remove the floormat, first remove:
a. Front seats and rear seat cushion. (Refer to pages S-l 10, 111, 112.)
b. Scuff plates and front side trim. (Refer to pages S-97, 98.)
c. B-pillar lower trim (PROTEGE) or quarter trim (Hatchback). (Refer to pages S-97, 98.)
d. Front seat belt lower anchor (hatchback with standard shoulder belt). (Refer to page S-100.)
e. Front seat belt buckles (standard shoulder belt models). (Refer to page S-100.)
f. Rear and front consoles. (Refer to page S-94.)
g. Passive shoulder belt retractor (passive shoulder belt models). (Refer to page S-108.)
h. Passive shoulder belt control unit (passive shoulder belt models). (Refer to page S-108.)
3 Remove the remaining parts in the order shown in the figure.
4 Install in the reverse order of removal.
1. Belt cover
2. Hole cover (With passive shoulder belt) 3. Floormat
s-99

S SEAT BELT
SEAT BELT
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable before removal of the passive shoulder belt and driver side front
seat belt buckle.
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
Caution
l Do not disassemble the buckle or retractor assembly.
Note
l Refer to PASSIVE SHOULDER BELT SYSTEM; page S-108 for removal/installation of the pas-
sive shoulder belt.
FRONT (STANDARD)
38-78 (3.9-8.0, 2
N.m (m-kg, ft-lb
)
13uosx-02 ‘0
1. Scuff plate 4. Front seat belt
Removal / Installation . . . . . . . . . pages S- 97, 98 Inspection . . . . . . . . . . . ,. . . ,. . . . . . . . . . . . . . . . page S-l 02
2. B-pillar lower trim (PROTEGE) 5. Buckle
Removal / Installation . . . . . . . . . . page S- 97 Inspection (Buckle switch) . . . . . . . . page S-102 -
3. Quarter trim (Hatchback)
Removal I Installation . . . . . . . . . . page S- 98
S-l 00