1992 MAZDA PROTEGE oil temperature

PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
Following items may be done at any time prior to delivery to your customer.
INSPECT and ADJUST, if necessary, the following items to
the specifications:
0 Glass, exterior bright metal and paint for damage
Cl Wheel lug nuts, and locks (if equipped)
88-118 N.m (9-12 m-kg, 65-87 ft-lb)
q All weatherstrips for damage or detachment
0 Operation of hood release and lock
0 Operation of trunk lid, rear hatch, and fuel lid opener
Cl With trunk open, check for spare jack, tire, tools, and
fasteners securing these items in place.
Cl Door operation and alignment
Cl Headlight aim
INSTALL the following parts:
Cl Wheel caps or rings (if equipped)
q Outside rearview mirror(s)
1 UNDER HOOD-ENGINE OFF )
INSPECT and ADJUST, if necessary, the following items to
the specifications:
0 Fuel, coolant and hydraulic lines, fittings, connections and
components for leaks
Cl Engine oil level
0 Power steering fluid level
0 Brake and clutch master cylinder fluid level
El Windshield washer reservoir fluid level
Cl Radiator coolant level
Cl Tightness of battery terminals
Cl Manual transaxle oil level
riizmiq
INSTALL the following parts:
Cl Rubber stopper for inside rearview mirror
CHECK operation of the following items:
0 Seat controls (sliding and reclining) and head restraint
Cl Folding rear seat
0 Door locks, including childproof door locks (if equipped)
Seat belts and warning system
Cl Ignition switch and steering lock
0 Inhibitor switch (ATX only)
U Starter interlock switch (clutch pedal, MTX only)
Cl All lights, including warning and indicator lamps
Cl Sound warning system
Cl Horn, wipers and washers (front and rear, if equipped)
0 Audio system (if equipped) 0 Cigarette lighter and clock
0 Sunroof (if equipped)
II Remote control outside rearview mirrors (if equipped)
Cl Power windows (if equipped)
q Heater, defroster and air conditioner at various mode
selections (if equipped)
CHECK the following items:
Cl Presence of spare fuse
0 Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
0 Pedal height and free play of brake and clutch pedal
Pedal height mm (in) Free play mm (in)
0 Parking brake
5-7 notches/98 N (10 kg, 22lb)
UNDER HOOD-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
q Automatic transaxle fluid level
[I
CHECK the following items:
Cl Underside fuel, coolant and hydraulic lines, fittings, con-
nections and components for leaks
0 Tires for cuts or bruises
0 Steering linkage, suspension, exhaust system and all un-
derside hardware for looseness or damage
[I
CHECK the following items:
0 Brake operation
0 Clutch operation
Cl Steering control
Cl Operation of gauges
q Squeaks, rattles or unusual noise
Cl Emergency locking retractors
0 Cruise control system (if equipped)
1 AFTER ROAD TEST (
CHECK for necessary owner information materials.
Following items must be done just before the delivery to your customer.
q Load test battery and charge if necessary
1 Volts 1 0 Install fuses for accessories
i.. _
0 Adjust tire pressure to the specification
Load test result cl Remove seat and floor mat protective covers
(Refer to door label) 0 Vacuum and clean interior of vehicle
0 Clean outside of vehicle q Inspect installation of option parts with invoice
23UOAX-002
A-2

SCHEDULED MAINTENANCE SERVICES (EXCEPT CANADA)
Follow Schedule 1 (Normal Driving Conditions) if the vehicle is mainly operated where none of the following conditions apply.
Follow Schedule 2 (Unique Driving Conditions) if any of the conditions below apply:
l Repeated short-distance driving.
l Driving in dusty conditions.
* Driving with extended use of brakes.
* Driving in areas where road salt or other corrosive materials are used.
l Driving on rough and/or muddy roads.
l Extended periods of idling and/or low-speed operation.
l Driving for prolonged periods in cold temperatures and/or extremely humid climates.
Schedule 1 (Normal Driving Conditions)
Number of months or miles (kilometers), whichever comes first
Months 7.5 15 22.5 30 37.5 45 52.5 60
7.5 15 22.5 30 37.5 45 52.5 60
12 24 36 46 60 72 64 96 Service data and inspection points Page
Bl-5
B2-5
D-5
D-5
Bl-12
B2-12
F-79
G-18 MAINTENANCE
OPERATION
m Cracks or damage
B Tension
m Oil pan capacity
B6 SOHC: 3.0 liters (3.2 US qt, 2.6 Imp qt)
All BP : 3.6 liters (3.8 US qt, 3.2 Imp qt)
l Oil filter capacity:
0.17 liter (0.18 US qt, 0.15 Imp qt)
-
l Plug gap: 1.0-l .l mm (0.039-0.043 in)
l Recommended spark plugs
Engine NGK NIPPONDENSO
B6 SOHC BKR5E-11 KIGPR-Ull
BKRGE-11 K20PR-U 11
BP SOHC BKR5E-11 KlGPR-Ull
BKRGE-11 K20PR-U 11
BKR5E-11 KlGPR-Ull
BP DOHC BKRGE-11 K20PR-U 11
BKR7E-11 K22PR-Ull I I
R R R R R R R R
R R R R R R R R Drive belts
Engine oil
Oil filter
Engine timing belt*’
Air cleaner element Replace every 60,000 miles (96,000 km)
I
Spark plugs

Bl TROUBLESHOOTING GUIDE
Problem
Insufficient power
Abnormal
combustion
Engine noise Possible Cause
Insufficient compression
Malfunction of HLA*
Compression leakage from valve seat
Seized valve stem
Weak or broken valve spring
Failed cylinder head gasket
Cracked or distorted cylinder head
Sticking, damaged, or worn piston ring
Cracked or worn piston Malfunction of fuel system
Malfunction of ignition system
Others
Slipping clutch
Dragging brakes
Wrong size tires Malfunction of engine-related components
Malfunction of HLA’
Sticking or burned valve
Weak or broken valve spring
Carbon accumulation in combustion chamber Malfunction of fuel system
Malfunction of ignition system
Crankshaft- or bearing-related parts
Excessive main bearing oil clearance
Main bearing seized or heat-damaged
Excessive crankshaft end play
Excessive connecting rod bearing oil clearance
Connecting rod bearing seized or heat-damaged Piston-related parts
Worn cylinder
Worn piston or piston pin
Seized piston
Damaged piston ring
Bent connecting rod Valves or timing-related parts
Malfunction of HLA*
Broken valve spring
Excessive valve guide clearance Malfunction of cooling system
Malfunction of fuel system
Others
Malfunction of water pump bearing
Improper drive belt tension
Malfunction of alternator bearing
Exhaust gas leakage
Malfunction of timing belt tensioner Action
Replace
Repair
Replace
Replace
Replace
Replace
Replace
Replace
Refer to Section F
Refer to Section G
Refer to Section H
Refer to Section P
Refer to Section Q
Replace
Replace
Replace
Eliminate carbon
Refer to Section F
Refer to Section G
Replace or repair
Replace
Replace or repair
Replace or repair
Replace
Replace or repair
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Refer to Section E
Refer to Section F
Refer to Section E
Adjust
Refer to Section G
Refer to Section F
Replace Page 81-20
Bl-57
81-55
81-58
81-16
81-54
81-62
al-62
81-20
81-55
81-58
-
61-71
Bl-64
81-72
81-73 8-i-64
Bl-60
81-63
81-62
81-62
El-63
Bl-20
El-58
81-55
Bl- 5
81-12
911 IORI .N)J LI.,“l. --
* Tappet noise may occur if the engine has set idle for an extended period. The noise should
normal operating temperature. (HLA troubleshooting: Refer to page Bl-7) dissipate after the engine has reached
81-4

ENGINE TUNE-UP PROCEDURE Bl
ENGINE TUNE-UP PROCEDURE
PREPARATION
-.
SST
drive belt tension
m :
I 1 2311081-058
- 03UOBX-20
---
OSUOBX-OC
V-BELT
LhEd
V-RIBBED BELT
OSJOBX-00
ENGINE OIL
Inspection
1. Be sure the vehicle is on level ground.
2. Warm up the engine to normal operating temperature and
stop it.
3. Wait for 5 minutes.
4. Remove the oil level gauge and check the oil level and con-
dition.
5. Add or replace oil if necessary.
Note
l The distance between the L and F marks on the level
gauge represents 0.8 liter (0.85 US qt, 0.70 Imp qt).
ENGINE COOLANT
Inspection
Coolant level (engine cold)
Warning
l Never remove the radiator cap while the engine is
hot.
l Wrap a thick cloth around the cap when removing it.
1. Verify that the coolant level is near the radiator filler neck.
2. Remove the coolant level gauge and check the coolant level.
3. Add coolant if necessary.
Coolant quality
1. Verify that there is no buildup of rust or scale around the
radiator cap or radiator filler neck.
2. Verify that the coolant is free of oil.
3. Replace the coolant if necessary.
DRIVE BELT
Inspection
1, Remove the air intake pipe.
2. Check the drive belts for wear, cracks, and fraying. Replace
if necessary.
3. Verify that the drive belts are correctly mounted on the
pulleys.
Bl--5

ENGINE TUNE-UP PROCEDURE Bl
Tightening torque
@ : 37-52 N,m (3.8-5.3 m-kg, 27-38 ft-lb)
@ : 19-25 Nsm (1.9-2.6 m-kg, 14-19 ft-lb)
23UOBl-OC
P/S belt, P/S + A/C belt
If necessary, loosen the P/S oil pump bolts @and nut @and
Oand adjust the belt deflection by turning the adjusting bolt
0.
Tightening torque
@I : 36-54 N.m (3.7-5.5 m-kg, 27-40 ft-lb)
@ : 19-25 N#m (1.9-2.6 m-kg, 14-19 ft-lb)
0: 31-46 N-m (3.2-4.7 m-kg, 23-34 ft-lb)
A/C belt
If necessary, loosen the locknut @and adjust rhe belt deflec-
tion by turning the adjusting bolt @.
Tightening torque:
31-34 N-m (3.2-3.5 m-kg, 23-25 ft-lb)
1
HLA
Problem Possible Cause Action
1. Noise when engine is started immedi- Oil leakage in oil passage Run engine 2000-3000 rpm.
ately after oil is changed. If noise stops after 2 second-10
2. Noise when engine is started after set- minutes(*), HLA is normal.
ting approx. one day. If not, replace HLA.
3. Noise when engine is started after Oil leakage in HLA - * Time required for engine oil to circu-
cranking for 3 seconds or more. late within engine, includes tolerance
4. Noise when engine is started after for engine oil condition and ambient
new HLA is installed. temperature.
5. Noise continues more than 10 minutes Insufficient oil pressure Check oil pressure.
If lower than specification, check for
cause.
Oil pressure; 294-392 kPa
(3.0-4.0 kg/cm*, 43-57 psi)-3000 rpm
(Refer to page 81-60)
Press down HLA by hand.
If it does not move,. HLA is normal.
If it moves, replace HLA.
t
I
Measure valve clearance.
If more than Omm (0 in), replace HLA.
5. Noise occurs durning idle after high-
speed running Incorrect oil amount
Deteriorated oil Check oil level.
Drain or add oil as necessary.
Check oil quality.
If deteriorated, replace with specified
type and amount of oil.
23UOBl-01
Bl-7

Bl COMPRESSION
COMPRESSION
If the engine exhibits low power, poor fuel economy, or poor idle, check the following:
1. Ignition system (Refer to Section G.)
2. Compression
3. Fuel system (Refer to Section F.)
23UOBl-01
23UOBl-06
23UOBl-014 23UOBl-012
INSPECTION
1. Check that the battery is fully charged. Recharge it if neces-
sary. (Refer to Section G.)
2. Warm up the engine to normal operating temperature.
3. Turn the engine OFF.
4. Remove all spark plugs.
5. Disconnect the ignition coil connector.
6. Connect a compression gauge to the No. 1 spark plug hole.
7. Fully depress the accelerator pedal and crank the engine.
8. Record the maximum gauge reading.
9. Check each cylinder.
Compression kPa (kg/cm*, psi)-rpm
10. If the compression in one or more cylinders is low, pour a
small amount of engine oil into the cylinder and recheck
the compression.
(1) If the compression increases, the piston, piston rings,
or cylinder wall may be worn.
(2) If the compression stays low, the valve may be stuck
or seating improperly.
(3) If the compression in adjacent cylinders stays low, the
cylinder head gasket may be defective or the cylinder
head distorted.
11. Connect the ignition coil connector.
12. Install the spark plugs.
05UOBX-020
Tightening torque:
15-23 N*m (1 S-2.3 m-kg, 11-17 ft-lb)
Bl-10

B2 TROUBLESHOOTING GUIDE
Problem
Insufficient power
Abnormal
combustion
Engine noise -
I
I
f
,
I
I
,
I
I Possible Cause Action Page
Insufficient compression
Malfunction of HLA*
Compression leakage from valve seat
Seized valve stem
Ueak or broken valve spring
Failed cylinder head
gasket Cracked or distorted cylinder head
Sticking, damaged, or worn piston ring
Cracked or worn piston Replace
Repair
Replace
Replace
Replace
Replace
Replace
Replace
Refer to Section F 82-22
82-57
02-55
B2-58
82-16
82-54
82-62
82-62 Malfunction of fuel system
Malfunction of ianition svstem
Others
Slipping clutch
Dragging brakes
Wrong size tires Malfunction of engine-related components
Malfunction of HLA*
Sticking or burned valve
Weak or broken valve spring
Carbon accumulation in combustion chamber Malfunction of fuel system
Malfunction of ignition system
Crankshaft- or bearing-related parts
Excessive main bearing oil clearance
Main bearing seized or heat-damaged
Excessive crankshaft end play
Excessive connecting rod bearing oil clearance
Connecting rod bearing seized or heat-damaged Piston-related parts
Worn cylinder
Worn piston or piston pin
Seized piston
Damaged piston ring
Bent connecting rod Valves or timing-related parts
Malfunction of HLA*
Broken valve spring
Excessive valve guide clearance Malfunction of cooling system
Malfunction of fuel svstem
Others
Malfunction of water pump bearing Refer to Section E
Improper drive belt tension Adjust
Malfunction of alternator bearing Refer to Section G
Exhaust gas leakage Refer to Section F
Malfunction of timing belt tensioner Replace Refer to Section G
Refer to Section H
Refer to Section P
Refer to Section C!
Replace B2-22
Replace 82-55
Replace 82-58
Eliminate carbon -
Refer to Section F
Refer to Section G
Replace or repair B2-70
Replace 82-64
Replace or repair 82-7 1
Replace or repair B2-72
Replace B2-64
Replace or repair
82-60
Replace 82-63
Replace 82-62
Replace 82-62
Replace 82-63
Replace
Replace
Replace
Refer to Section E
Refer to Section F 82-22
82-58
82-55
B2- 6
82-12
23UOB2-00,
..J
.-,
l
Tappet noise may occur if the engine has set idle for an extended period. The noise should dissipate after the engine has reached
normal operating temperature. (HLA troubleshooting: Refer to page 82-7.)
82-4

ENGINE TUNE-UP PROCEDURE 82
ENGINE TUNE-UP PROCEDURE
PREPARATION
SST
49 BO19 9AO
drive belt tension
23UOB2-048
OBUOBX-158
I’ ,
OSJOBX-001
V BELT
V RIBBED BELT
_
x 0 x
3
L
03UOB2-005
ENGINE OIL
Inspection
1. Be sure the vehicle is on level ground.
2. Warm up the engine to normal operating temperature and
stop it.
3. Wait for 5 minutes.
4. Remove the oil level gauge and check the oil level and con-
dition.
5. Add or replace oil if necessary.
Note
l The distance between the L and F marks on the level
gauge represents 0.8 liter (0.85 US qt, 0.70 Imp qt).
ENGINE COOLANT
Inspection
Coolant level (engine cold)
Warning
l Never remove the radiator cap while the engine is
hot.
l Wrap a thick cloth around the cap when removing it.
1. Verify that the coolant level is near the radiator filler neck.
2. Remove the coolant level gauge and check the coolant level.
3. Add coolant if necessary.
Coolant quality
1. Verify that there is no buildup of rust or scale around the
radiator cap or radiator filler neck.
2. Verify that the coolant is free of oil.
3. Replace the coolant if necessary.
DRIVE BELT
Inspection
1. Check the drive belts for wear, cracks, and fraying. Replace
if necessary.
2. Verify that the drive belts are correctly mounted on the
pulleys.
B2-5