1992 Lexus ES300 reset

AIR CONDITIONER AND AUDIO
75
Radio operation
”AM” button
(For turning radio on
and selecting AM)
“PWR. VOL” knob
(For turning radio on
and adjusting volume)
“SCAN” button
(For preset scan tuning
and scan tuning)
“TUNE SEEK” button
(For tuning to frequency)
“BASS” knob
(For bass control)“MID” knob
(For mid range control)“TREBLE” knob
(For treble control)“BALANCE” knob
(For right and left
sound balance)
”FADER” knob
(For front and rear
sound balance)
Station selector
buttons
Radio display
“FM2” button
(For turning radio on
and selecting FM)“FM1” button
(For turning radio on
and selecting FM)
Without compact disc player

“AM” button
(For turning radio
on and selecting AM)
“PWR. VOL” knob
(For turning radio on
and adjusting volume)
“SCAN” button
(For preset scan tuning
and scan tuning)
“TUNE SEEK” button
(For tuning to frequency)
“BASS” knob
(For bass control)“MID” knob
(For mid range control)“TREBLE” knob
(For treble control)“BALANCE” knob
(For right and left
sound balance)“FADER” knob
(For front and rear
sound balance)
Station selector
buttons
Radio display
“FM1 / 2” button
(For turning radio on
and selecting FM)
With compact disc player
AIR CONDITIONER AND AUDIO
76

AIR CONDITIONER AND AUDIO
77 (a) Listening to the radio
1. Push the
(AM), (FM1) or (FM2) button to turn
the radio on and to select either an AM or FM broadcast
(without compact disc player).
2. Push the
(AM) or (FM1/2) button to turn the radio
on and to select either an AM or FM broadcast (with compact
disc player).
“AM”, “FM 1” or “FM2” will appear on the display.
The radio can also be turned on by pushing the “PWR.VOL”
knob if the radio was being used when the system was turned
off.
3. Turn the “PWR.VOL” knob to adjust the volume.
4. Tune in the desired station. (See “(b) Selecting a station”.)
The radio will change automatically to stereo reception when
an AM (Motorola type) or FM stereo broadcast is being
received. At the same time, “ST” will appear on the display.
When the receiving signal gets weak, the channel separation
will automatically be reduced for lowest noise. If the signal
becomes extremely weak, the radio will switch over to
monaural reception.
5. Adjust the tone and sound balance. (See “(d) Adjusting the
tone” and “(e) Adjusting the sound balance”.)
6. To turn the radio off, push the “PWR.VOL” knob.
(b) Selecting a station
Tune in the desired station using one of the following methods.
The frequency will appear on the display.Preset tuning: Use for tuning-in to a desired preset station.
Push the station selector button to which the desired station
has been preset. The radio will tune in to the station and the
button number will appear on the display. (See “(c) Presetting
a station”.)
Seek tuning: Use for automatic station search and stop.
Push the (SEEK) button until a beep is heard. The radio will
begin seeking up or down for a station of the nearest frequency
and will stop on reception. Each time you push the button,
stations will be searched out one after another.
If the radio cannot seek out any stations in one pass because
signals are too weak, the radio will begin seeking again with
sensitivity boosted for searching out weak stations. At this
time, “DX” will appear on the display.
Scan tuning: Use for scanning preset station channels or
station-to-station scanning.
Push the
(SCAN) button for less than 2 seconds. With “P.
SCAN” blinking on the display, the radio will automatically seek
out a preset station of a higher channel number in the AM/FM
mode. If there is a preset station on the channel, then the tuning
is held for 5 seconds. If there is no station on the channel, then
the tuning is only held for 1 second. If the (SCAN) button
is pushed while listening to a preset station channel, then the
scan proceeds to the next highest channel, proceeding in turn
through the 6 channels of FM1 and then the 6 channels of FM2,
then repeating the process. To continue listening to the
channel of your choice, simply push the (SCAN) button
once again.

AIR CONDITIONER AND AUDIO
78Push the (SCAN) button for longer than 2 seconds. With
“SCAN” on the display, the radio will automatically seek out a
station of higher frequency, hold it for 5 seconds and scan to
the next. To continue listening to the broadcast of your choice,
simply push the (SCAN) button once again.
If the radio scans over all frequencies without stopping
because the signals are too weak or because you leave it
scanning, the radio will begin scanning again with sensitivity
boosted for searching out weak stations. At this time, “DX” will
appear on the display.
Manual tuning: Push the (TUNE) button within 0.5
seconds. Each time you push the button, the radio will step up
or down to another frequency where stations could exist.
(c) Presetting a station
1. Tune in the desired station. (See “(b) Selecting a station”.)
2. Push one of the station selector buttons and hold it until a
beep is heard. This sets the station to the button and the button
number will appear on the display.
Each button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station will be cancelled when the power source is
severed (battery disconnected, burnt fuse, etc.).(d) Adjusting the tone
To adjust the low-pitched tone, push the “BASS” knob (if
depressed) and turn it.
To adjust the middle-pitched tone. push the “MID” knob (if
depressed) and turn it.
To adjust the high-pitched tone, push the “TREBLE” knob (if
depressed) and turn it.
(e) Adjusting the sound balance
To balance the sound between the right and left speakers,
push the “BALANCE” knob (if depressed) and turn it.
To balance the sound between the front and rear speakers,
push the “FADER” knob (if depressed) and turn it.
Radio operating tips
The antenna automatically extends to full height when the
radio and ignition are turned on and retracts when either is
turned off.
CAUTION:
Before extending the antenna, confirm that no one is close
enough to get injured.
NOTICE:
To prevent damage to the antenna, make sure it is
retracted before running your vehicle through an
automatic car wash.

AIR CONDITIONER AND AUDIO
88(d) Selecting a program
Automatic program selection: Use for direct access to a
desired program.
Push the (TRACK) button on either side and hold it
until the desired program number appears on the display. As
you release the button, the player will start playing the selected
program from the beginning.
Manual program selection:
Push the (FF) button on the right side and hold it to fast
forward the disc. Releasing the button starts play from that
position.
Disc scan selection: Use for disc-to-disc scanning.
Push the (SCAN) button. With “SCAN” on the display, the
program at the beginning of each disc will be played for 10
seconds. To continue listening to the program of your choice,
push the (CD) or (SCAN) button.
(e) Other compact disc player functions
“RPT” button: Use for automatic repeat of the program
currently being listened to.
Push the (RPT) button on the left side while the
program is being played. As this is done, “RPT” will appear on
the display. When the program is finished, the disc will
automatically go back to the beginning of the program and the
program will be played again. To cancel it, push the button
once again.“RANDOM” button: Use for automatic program selection and
play by the system.
When the (RANDOM) button on the right side is
depressed, “RND” appears on the display and the system
selects a program on the disc which is set and plays it. To
cancel it, push the button once again.
When a program is skipped or the system is inoperative, push
the (CD) button to reset.
“CD CMP” button: Use for listening to music in noisy
situations.
Push the (CD CMP) button and hold it until a beep is
heard. Small sounds are then emphasized and large sounds
muted slightly so that every sound can be heard clearly.
This function works only in the “CD” mode. To cancel it, push
the button once again and hold it until a beep is heard.
(f) If the player malfunctions
If “WAIT” appears on the display, audio signals of the disc
cannot be read or the system has trouble. Push the (CD)
button once again.
If the player does not operate, check that the disc surface is not
soiled or damaged. If the disc is O.K., the following two causes
are possible.

Condensation may have occurred on the internal
mechanism of the player.
Open the trunk to let air circulate.

AIR CONDITIONER AND AUDIO
90
If the disc gets dirty, clean the disc by wiping the surfaces
radially out from the center with a soft cloth.
Do not use a conventional record cleaner or anti-static record
preservative.
CAUTION:
Compact disc players use invisible laser beams which
could cause hazardous radiation exposure if directed
outside the unit. Be sure to operate the player correctly as
instructed.
Anti-theft system
To deter theft of your radio, the system is designed so that
the radio unit becomes inoperable if it is stolen from the
vehicle.
The system is not preset at the factory. You must input a
three-digit identification number decided by you.
(a) Setting the anti-theft system
1. Make sure the radio unit is turned off with the ignition switch
in “ACC”.
2. While holding the left side of the (1) and right side
of the d (6) buttons in, push and hold the “PWR.VOL”
knob in until “SEC” appears on the display.

AIR CONDITIONER AND AUDIO
94(c) If the anti-theft system is activated
Error times
(1 - 9)
The audio system made inoperable by the activated anti-theft
system will be operable if you give it the correct identification
number.
1. Follow steps 3 and 4 described in “(a) Setting the antitheft
system”.
2. With your identification number appearing on the display,
press the (SCAN) button and hold it in until “SEC” appears
on the display. “SEC” will go off to indicate that the system is
reset and the audio system is operable. If invalid buttons have
been used, “Err” will appear on the display before “SEC”
appears. Try again from the beginning.
See “(b) Cancelling the anti-theft system” for notes on the
number displayed with “Err”.The number displayed with “Err” indicates how many errors
you have made. You may make up to nine errors, but no more!
Indicator light
“HELP”
NOTICE:
A tenth error will activate the anti-theft system and
“HELP” will appear on the display. The audio system will
be completely inoperable. At this time, the indicator light
also comes on. If this occurs, contact your Lexus dealer.