1992 FORD SIERRA engine

Turbocharger
pC
pG/H/I
pF
pD
pA
pB
pE
pA Standard Wastegate Actuator Since the stock XR
wastegate is no longer available new, we supply a high quality
re manufactured unit. Internal components (diaphragm) are re-
placed and exterior is zinc plated.) M521WR
pB
Turbochargers We offer both re manufactured stock
specification and modified high performance turbos for the
XR. High quality re manufactured turbos include; new center
cartridge compressor/turbine wheel assembly with recondi-
tioned outer compressor/turbine housings, new bearings,
seals and O-rings and fasteners. Our high performance turbo
adds a few extra tweeks. A GNX compressor wheel machined
into the stock comp housing for an additional 30% airflow and
a 360 degree thrust bearing is fitted for added durability.
Turbos are fully dressed and include wastegate actuator,
base & drain gaskets and sold on a exchange "core" basis-
outright purchase will add an additional $100.00 to the cost.
Standard Reman. Turbocharger M522TR
High Performance Turbocharger M522TM
pC
Intercooler Kit If you are looking for a large high flow
intercooler kit this is the one to have. Intercooler core mounts
ahead of the steering rack in front of the engine facing the
ground. Air is ducted up and through the core. Plumbing is kept
short and allows for a larger core than what can usually be fitted
in the bumper/grille area. Kit is complete with intercooler core
(8" x 20" x 3.5"), mounting brackets, inlet plumbing pipes &
connectors, clamps, turbo output elbow, bypass valve and
additional hardware and instructions.
M522ICpD
Adjustable Boost Valve Kit Replace the troublesome
stock boost control solenoid with this easy to adjust under hood
boost valve. This kit uses a check valve to accurately control the
boost level which allows for faster turbo spool-up (reduced lag)
over typical adjustable "bleed-off" valves. This is a low cost modifi-
cation and should be a "must have" for all XR's.
M521BV
pE
Dual Port Wastegate Actuator These are new actua-
tors which feature an adjustable length rod (set boost & pre load)
and dual vacuum ports. The dual port feature permits use of a
remote mounted boost valve (see below), but can also be used
as a replacement for stock actuator.
M521WA2
pF
Cockpit Mounted Boost Valve Remote cockpit
mounted adjustable boost valve for use with dual port wastegate
actuators (see above). Vacuum signal is regulated by the in
car mounted valve and recirculated to the dual port actuator for
precise adjustment. M521TB
pG
Turbo Oil Feed Pipe is prone to cracking/leaking and
should always be replaced when a new turbo is fitted to assure
proper oil flow. Just look inside an old one and you will see
what we mean. M522P
pH
Turbo Inlet Hose we have a version of this (discontin-
ued by Ford) hose that links the turbo outlet pipe to the throttle
body. Ours is high specification 4-ply Silicone (blue) rated to
over 600 degrees, 190 psi burst pressure- better & cheaper
than the original ! M22H
pI
Stainless Base Gasket replacement for between the turbo
base and exhaust manifold. L521GT
2 5

Engine & Related Items
pA
pB
pC
pE pDpA
Performance Engine Bearings2.3L At engine rebuild time one item
not to skimp on are engine bearings. We supply only the finest ACL/Vandervell
heavy duty lead-indium type bearings. All bearings are not alike, regardless of
who's name is on the box. Lead-indium bearings, not lesser reticular tin-
aluminum, are the only type you will find in quality performance engines.
Main Bearing Set- ACL/Vandervell (standard)L16A
Main Bearing Set- ACL/Vandervell (+.010" over)L16B10
Main Bearing Set- ACL/Vandervell (+.020" over)L16B20
Main Bearing Set- ACL/Vandervell (+.030" over)L16B30
Rod Bearing Set- ACL/Vandervell (standard)L16H
Rod Bearing Set- ACL/Vandervell (+.010")L16110
Rod Bearing Set- ACL/Vandervell (+.020")L16120
Rod Bearing Set- ACL/Vandervell (+.030")L16130
Cam Bearing Set- ACL/VandervellL16M
Cam Bearing Set- ACL/Vandervell (360 degree O.D. groove)L16MA
Auxiliary Shaft BearingL5DC
pB
Performance Engine Fasteners As with engine bearings, skimping
on fasteners is false economy. As a minimum install a set of H.D. rod bolts and
nuts for an added degree of reliability.
Con Rod Bolt Set (H.D. SPS type)
for standard 2.3 rodL4FS
Con Rod Bolt Set (H.D. SPS type)
for 5.7 Chevy I-6 rodsL4FSC
Head Stud Set (H.D. SPS type)L2DS
Main Cap Stud Set (H.D. SPS type)L2KS
pC
Engine Gaskets (2.3L Turbo) We have a wide range of performance
and speciality gaskets available for the 2.3L turbo engine from full sets to
individual pieces.
Full Gasket Set (complete engine)
FelproL15AA
Top End Gasket Set (cylinder head, valve train, inlet/exhaust) FelproL15BA
Bottom End Gasket Set (block, crank & sump)
FelproL15CA
Pan Set- sump rails & seals (cork)L15CP
Head Gasket H.D. (Ford Motorsport turbo style)L15D
Head Gasket H.D.-
FelproL15DA
Head Gasket Competition-
Felpro #1035 (steel wire ring type)L15DF
Head Gasket Competition (extreme duty racing gasket)L15DR
Head Space Shim .020"L15DS
Valve Cover Gasket (standard cork)L15E
Valve Cover Gasket H.D. (hi-temp rubber / includes- upper inlet gasket)L15EA
Intake Manifold Gasket Set (upper
& lower inlet manifold)L15F
Water Outlet Gasket (thermostat housing)L15N
Water Pump Gasket (pump to block)L15P
Crankshaft Rear SealL15Q
Camshaft SealL15R
Auxiliary Shaft SealL15S
Crankshaft Front SealL15T
pD
2.3 Turbo Inlet Hose We have a version of this (recently discontinued
by Ford) hose that links the turbo outlet pipe to the throttle body on XR4Ti,
T-Bird & SVO. Ours is higher specification 4-ply Silicone (blue) rated to over 600
degrees, 190 psi burst pressure- better & cheaper than the original ! M22H
pE,F
Exhaust Components We offer the Modern Performance line of
exhaust related items for the XR4Ti including full systems (hi-flow down pipe,
converter and muffler) as well as cat back systems (excludes converter).
Exhaust piping and mufflers are constructed in heavy 14 gauge aluminized
tubing, converters and mufflers are straight through design for minimum
restriction. These systems are unparalleled for performance and sound great
too. The 3" down pipe can be added to standard or
Borla systems for increased
performance. We also stock the standard Ford cast iron exhaust manifolds
(which are prone to cracking) or alternate stainless tubular exhaust headers.
Exhaust System 3" (full system)
S.S. muffler & converterM522
Performance Exhaust System 2.5" (down pipe w/cat back)M522B
Exhaust Down Pipe 3"M522DP
Exhaust Manifold (standard cast Fomoco)M521
Exhaust Header 2.3 Turbo (tubular stainless steel)L521T
Gasket (stainless)- Turbo to Exhaust ManafoldL521GT
Exhaust Hanger (rubber donut)C522H
pF
2 6

Engine & Related Items
2.5mm metallic inductance EMI
suppressed conductor: with
stainless steel windings spaced
over ferrimagnetic core
substrate
serves as
strength
member for
cable assembly
ignition cables have a non-layered high strenght insulating
jacket made entirely of aerospace grade silicone rubber to
prevent swelling and splitting at extreme trmperatures
KV85 & R-100
metallic inductance EMI
suppressed conductor
pA Performance Air Filters A quick and easy performance modification
is to replace the standard air filter with a direct fit KN high performance air filter.
Merkur XR4Ti (2.3L Turbo)M22P
Merkur Scorpio (2.9L V-6)G22P
pB
High Temp Fyre Sleeve The under hood temperatures on the XR4Ti can
be quite severe. Slipping a length of fyre sleeve over critical wiring or rubber water
& A/C hoses will add an extra degree of protection. Fyre Sleeve provides radiant heat
protection up to 800 degrees. Sleeve is sold per foot and is sized by internal diameter.
Hoses or wiring can be disconnected at one or both ends then slipped through fyre
sleeve or sleeve can be un-stitched at the seam and wire tied in place.
Mylar Fyre Foil Sleeve -10 (7/8" I.D.) per foot320510
Mylar Fyre Foil Sleeve -12 (1" I.D.) per foot320512
Mylar Fyre Foil Sleeve -16 (1 1/4" I.D.) per foot320516
Mylar Fyre Foil Sleeve -20 (1 1/2" I.D.) per foot320520
pC
Engine Mount Insulators BAT has an alternative to the recently
discontinued original equipment Ford motor mounts on the XR4Ti. Simply
remove the old motor mount assemblies, discard the worn-out rubber
portion, and reuse the top and bottom metal plates with our replacement
insulators.
Note: slight modification requires 10mm holes in plates to be
increased to 12mm. Scorpio mounts are Ford mfg. direct replacements.
Engine Mount Insulator (left & right same) XR4TiM433
Engine Mount Insulator (left & right same) Scorpio-
new FordG433
pD
Transmission Mount /Insulator Rear transmission mount/insulator-
direct fit for automatic & manual Scorpio. A heavy duty version also available.
Note:
this "square" type mount can be fitted to the XR4 with special crossmember, (see
below) as the standard "round" trans. mount used on our XR4Ti's is no longer available.
Transmission Mount Insulator*- (automatic & manual) G433T
Transmission Mount Insulator H.D*.- (automatic & manual) M433TA
*can be fitted to XR4 with additional x-member (see below)
pE Transmission Crossmember Wide and narrow type transmission
tunnel crossmenbers allow the above "square" mount/insulators to be installed in
the XR4Ti. Fitting the XR with this crossmember/mount combination is a consider-
able upgrade (strength, noise, vibration) over the USA supplied "round" mount.
Crossmember* XR4 (wide) 1987-89- manual & auto M433XL
Crossmember* XR4 (narrow) 1985-86- manual & autoM433X
*for use in combination with above G433, M433 "square" type mount
pF Engine Belts H.D. Our search for the ultimate heavy duty engine
accessory v-belts lead us to the top cog "Gold Series" by Dayco. Top cog v-
belts are built to last up to 20% longer than conventional belts. A unique cogged
design increases flexibility and airflow around the belt for reduced friction and
heat. Laminated design with high temperature rated polyester cords provide
maximum tension holding (reduced slip) over the life of the belt.
Belt- XR4Ti (1985-89) W. Pump, Alt, P. Steering (2 required)M6G
Belt- XR4Ti (1986-89) A/C CompressorM6H
Belt- XR4Ti (1985) A/C CompressorM6HA
Belt- Scorpio (1988-89) Fan & Power Steering (2 required)G6G
Belt- Scorpio (1988-89) AlternatorG6GA
Belt- Scorpio (1988-89) A/C CompressorG6H
pG
Performance Ignition Wire Sets We have tried a number of
different ignition wire options on the 2.3 Turbo and 2.9L V6 engines and have
found the Magnecor brand to offer superior quality, performance, and durability.
Cables are red in color with 8mm, 8.5mm and 10mm cable diameters.
Merkur XR4Ti (2.3L Turbo)
Ignition Wire Set- (8mm w/silicone jacket and boots)L9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)M9HT
Ignition Wire Set- (10mm R-100 wire w/silicone jacket and boots)M9HTR
Merkur Scorpio (2.9L V6)
Ignition Wire Set- (8mm w/silicone jacket and boots)G9HT
Ignition Wire Set- (8.5mm KV85 wire w/silicone jacket and boots)G9HT9 pG
pF
pA
Aluminized Mylar Fyre Sleeve
pB
pC pD
pE
2 7

L4-218
L2G L4ES
L15D
L15DS
L604A
L15E
L2KS L4FS
2300 Turbo Engine Components
Cylinder Block Bare (H.D. "Turbo" Block) L2G 475.00
Main Cap Stud Set (H.D. ARP) L2KS 94.55
Full Gasket Set (Felpro)
1985 engineL15AA 95.00
Full Gasket Set (Felpro)
1986-89 engineL15AB 124.50
Top End Gasket Set (Felpro)
specify year when orderingL15BA 55.00
Top End Gasket Set (Felpro)
with hi-temp valve cover setL15BB 79.50
Bottom End Gasket Set (Felpro)
1985 engine (cork pan)L15CA 40.10
Bottom End Gasket Set (Felpro)
1986-89 engine (rubber pan)L15CB 73.85
Oil Pan Gasket (1 piece rubber) 1986-89 L15CP 34.25
Head Gasket (Felpro) L15DA 19.50
Competition Head Gasket (Felpro #1035)
steel wire ring typeL15DF 59.50
Competition Head Gasket (extreme duty racing gasket) L15DR 29.50
Valve Cover Gasket- Cork L15E 6.79
Valve Cover Gasket H.D. (1 piece rubber) includes upper manifoldL15EA 24.00
Intake Manifold Gasket Set L15FA 11.40
Exhaust Manifold to Cylinder Head L15GA 7.50
Turbo Charger to Exhaust Manifold (stainless) L521GT 8.75
Water Outlet Gasket L15N CALL
Water Pump GasketL15P CALL
Camshaft Seal L15R 8.25
Auxiliary Shaft Seal L15S 9.25
Crankshaft Front Seal L15T 16.08
Oil Pump (standard)
MellingL2P 42.90
Oil Pump- (high pressure/ high volume) L2HP 73.20
Water Pump (new) L6A 73.10
Water Pump (recon) L6AA 39.00
Fuel Pump- Electric XR4Ti (in line) M10A 165.00
Fuel Pump- Electric XR4Ti (in tank) M10AT 125.00
Engine Components
Utilizing a design similar to the earlier German
2000 OHC "Pinto" engine the 2300 "Lima" en-
gine eventually replaced the 2000 OHC in most
North American Ford 4 cylinder vehicles from
1974 on. Built for lower maintenance with the
addition of hydraulic lash
adjusters the 2300
was designed to
operate in a lower
RPM range using
its larger displace-
ment and in-
creased torque to
its best advan-
tage. Perfor-
mance turbo-
charged versions
of the 2300 began
to appear in 1979 in
the Mustang/Capri and continued through the
80's in a more refined and powerfull EFI turbo
version. A reduced bore 2000 displacement
"Ranger" truck engine (from 1983-87) was also
produced. Some late production "Lima" engines
are equipped with hydraulic roller cam and valve
train, and other versions use dual spark plug
cylinder heads. The 2300 is a fairly rugged
engine in its stock form, however some compo-
nents will require up-rating with performance
components if high RPM duty is required. The
"Lima" series turbo and normally aspirated en-
gines respond quite well with a bit of perfor-
mance tuning and though lacking in refinement
do give quite a bit of bang for the buck.
Main Bearing Set- ACL/Vandervell (std, .010", .020", .030") L16A 32.65
Connecting Rod Set- (4) Forged H-beam 5.20" length L4ES 549.00
Connecting Rod Set- (4) Forged
I-beam 5.20" length L4ESB 398.00
Connecting Rod Set- (4) Forged H-beam 5.70" length L4ESA 549.00
Rod Bearing Set- ACL/Vandervell (std, .010", .020", .030") L16H 16.35
Con Rod Bolt Set- ARP H.D. (for standard 2.3L rod) L4FS 47.70
Head Stud Set- ARP H.D. L2DS 105.00
Cam Bearing Set- ACL/Vandervell L16M 18.50
Cam Bearing Set- ACL/Vandervell (360 degree O.D. groove) L16MA 18.50
Aux. Shaft Bearing L5DC 20.25
Cam Follower- (standard O.E. type)
eachL5B 7.50
Cam Follower- (roller type)
eachL5BR 16.00
Ring Set- Moly type 1/16", 1/16", 3/16" (std, .020", .030", .040", .060")

*for above "performance pistons" - specify sizeL4R 85.90
Ring Set*- Gapless Moly type 1/16", 1/16", 3/16" (std, .020", .030", .040", .060")

*for above "performance pistons" - specify sizeL4TF 98.00
Ring Set*- Gapless Moly type 1/16", 1/16", 3/16" (std, .025", .035", .045", .065")

*for above "performance pistons" - file fit top ringL4T1 127.50
Ring Set*- Gapless Moly type 2mm, 2mm, 4.75mm (std, .020", .030", .040", .060")
*for standard OE type pistons - specify sizeL4TFA 98.00
Performance Piston- Power Forged #250F (std, +.020", +.030", +.040", +.060 sizes)
exact replacement for standard 2.3 turbo piston, light weight "power forged"
design, 1.589" comperssion height for 8.0:1 compression, 2mm 2mm 4.75mm
ring land, supplied with wrist pins and locks.
L4-250F 62.20
Performance Piston- Forged (custom)
BAT can supply custom forged pistons to your specifications. Information regarding
bore size, ring land sizes & locations, compression height, and wrist pin bore size
is required for ordering. Pricing is on request
2 8

Engine Components
Camshafts- see chart below
Hydraulic Lash Adjuster Set- (standard O.E. type) L5BA 43.00
Hydraulic Lash Adjuster Set- (high rev. anti pump-up) L5BH 49.95
Intake Valve- (standard O.E. type) L3H 8.25
Intake Valve- 1.740" (oversized stainless steel hi-flow)
eachL3HA 13.25
Intake Valve- 1.890" (oversized stainless steel hi-flow)
eachL3HB 15.00
Exhaust Valve- (standard O.E. type)
eachL31 25.75
Exhaust Valve- 1.510" (oversized stainless steel hi-flow)
eachL31A 13.25
Exhaust Valve- 1.590" (oversized stainless steel hi-flow)
eachL31B 15.00
Valve Spring Retainers (various)-
call with specific application------CALL
Valve Spring Set- (sport spring set for hydro cams to .480" lift) L3F 73.75
Valve Springs Racing-
call with specific application------CALL
Electric Fan Switch -XRM450FS 24.50
Knock Sensor-XRM450KS 52.70
Engine Coolant Temp Sensor (ECT)-XR M450EC 28.45
Idle Speed (Air Bypass Valve) XR/Scorpio
M450IS 79.90
Throttle Position Sensor (TPS)-XR M450TP 47.60
Oxygen Sensor (OS)-XRM450OS 60.50
Oil Pressure Switch-XRM450P 6.40
Water Temp Gauge Sender- XR (purple band)M450F 39.75
Adjustable Cam Sprocket (key way type) L5F 34.95
Adjustable Cam Sprocket (vernier type) L5FA 95.75
Cam Belt- (H.D. Ford Motorsport) L5G 29.95
Cam Belt- (H.D. Pirelli type)L5GA 15.00
Fuel Injector 2.3L Turbo (35pph -disk type) each L7G 68.50
Fuel Injector 2.3L Turbo- Remanufactured (35pph -brown top) each M7G 49.50
Intake Hose- Turbo Outlet to Throttle Body (Hi-Temp 4-Ply Silicone "Blue") XR4Ti, T-Bird & SVO M22H 47.00
Air Vane Meter* 50mm (T-Bird)
reconditionedL7V 164.50
Air Vane Meter* 65mm (SVO)
reconditionedL7VA 175.00
*can also be used for performance upgrade on XR4Ti with "PE" programed chip (call for information)
Distributor- 2.3L Turbo (reman) w/o cap, rotor, module (35.00 core) L9AB 119.00
Distributor Cap H.D. (hi-temp epoxy w/brass terminals) L9B 16.98
Distributor Rotor H.D. (hi-temp epoxy)
85-86 screw down typeL9F 7.50
Distributor Rotor H.D. (hi-temp epoxy)
87-89 push-on typeL9FA 8.90
Ignition Module TFI (on distributor) L9M 80.75
Ignition Wire Set- (8mm custom length w/silicone jacket and boots)L9HT 39.00
Ignition Wire Set- (8.5mm custom length w/silicone jacket and boots) M9HT69.50
Ignition Wire Set- (10mm custom length w/silicone jacket and boots)M9HTR 79.50
Performance Air Filter KN (2.3L Turbo) XR4Ti M22P 32.50
*durations quoted gross & .050" - timing events are @.050"
Grind#
Pricing $DescriptionPower
BandCam Lift
inlet/exhst.Valve Lift
inlet/exhst.Duration
inlet/exhTim ing
FiguresTiming
Inlet @
Full LiftValve
Clearance
inlet/exhst.Com m ents
2300 Turbo Camshafts (Hydraulic)
H260
$169.00Hydraulic2500-6000.252"/.252".416"/.416"272/272
220/2200/40 40/01100 / 0smooth idle, strong low and mid performance,
turbo suitable, auto & manual trans.
H283
$169.00Hydraulic3500-6500.274"/.274".453"/.453"276/276
224/2242/42 42/21100 / 0good idle, strong low and mid performance,
turbo suitable, manual transmission only
2300 Turbo Camshafts (Hydraulic Roller*) *for cars origionally equipped or kit available below
HR220
$385.00Hydro-roller2700-6500.305"/.305".505"/.505"272/222
221/231------1110 / 0H.P. roller cam for cars origionally roller cam equipped,
or see kit below- manual transmission only
HR225
$399.00Hydro-roller3000-6800.314"/.314".520"/.520"280/280
226/226------1110 / 0H.P. roller cam for cars origionally roller cam equipped,
or see kit below- manual transmission only
HR310
$375.00Hydro-roller3000-7000.317"/.317".535"/.535"284/284
224/2240/44 44/01120 / 0H.P. roller cam for cars origionally equipped.
turbos use 112 centerline, manual transmission only
2300 Turbo Camshaft Kits (Hydraulic Roller)
HR220K
$680.00Hydro-roller
cam kit2700-6500.305"/.305".505"/.505"272/222
221/231------1110 / 0Kit Includes: camshaft, roller followers, valve springs,
valve keepers & retainers, lash caps & cam oil seal
HR225K
$715.00Hydro-roller
cam kit3000-6800.314"/.314".520"/.520"280/280
226/226------1110 / 0Kit Includes: camshaft, roller followers, valve springs,
valve keepers & retainers, lash caps & cam oil seal
2 9

Engine Builders Kits
Time for that inevitable engine rebuild? BAT takes the guess work out of acquiring
all the right components by offering these prepackaged performance engine service
kits. Our top end (cylinder head) and bottom end (short block) rebuilding kits are
supplied complete with premium high performance parts. With the help of a competent
machine shop these rebuild kits will restore your engine to better than new condition.
As usual we have gone to great lengths to supply only the absolute best components
for the job and still managed to keep the prices reasonable.
Performance Short Block Rebuild Kit (2.3L Turbo)
(1) Full Gasket Set -Felpro L15AB
(1) Main Bearing Set -ACL Vandervell (specify size; STD, +.010", +.020", +.030") L16A
(1) Rod Bearing Set -ACL Vandervell (specify size; STD, +.010", +.020", +.030") L16H
(4) Forged Pistons -Power Forged (specify size; STD, +.010", +.020", +.030", +.040",
+.060")
L4250F
(1) Gapless Ring Set -Total Seal (specify size; STD, +.010", +.020", +.030", +.040",
+.060")
L4TF
(1) Rod Bolt & Nut Set H.D. -A.R.P. L4FS
(1) Oil Pump- Melling L2P
Short Block Rebuild Kit L501
$649.00
as above listed
Optional Items to Short Block Rebuild Kit
A) Forged Connecting Rod Set - "I" beam type w/ H.D. fasteners (add $350.00)
B) Forged Connecting Rod Set - "H" beam type w/ H.D. fasteners (add $525.00)
C) Main Stud Set H.D. - A.R.P. (add $75.00)
D) Crankshaft (if required) - resized, polished, balanced, indexed (add 349.00)
E) Crankshaft "Power Pulley" (add $90.00)
Performance Cylinder Head Rebuild Kit (2.3L Turbo)
(1) Top End Gasket Set* - Felpro L15BA * see notes below
(1) Cam Bearing Set -ACL Vandervell
L16M
(1) Head Bolt Set L2D
(4) Exhaust Valves -Stainless Hi-flow 1.51" L31A
(4) Inlet Valves -Stainless Hi-flow 1.74" L3HA
(1) Valve Spring Set H.D. L3F
(8) Cam Followers L5B
(1) Hydraulic Adjuster Set (lifters) L5B
(1) Cam Sprocket (index type) L5F
(1) Cam Belt H.D. L5G
(1) Camshaft (.416" / 272 turbo profile) L5H260
Cylinder Head Rebuild Kit L502
$649.00
as listed above
Optional Items to Cylinder Head
(A) Head Stud Kit H.D. - A.R.P. (add 45.00)
(B) Adjustable Cam Sprocket -alloy
"vernier" type (add 50.00)
*Notes: this item (L15BA) is not required when ordering L502 cylinder head kit with
L501 short block kit (it is already included with L501). We will offer a 50.00 discount
when ordering L502 and L501 together.
MOTOR RACING COMPONENTS
SPEED-PRO
RACING PRODUCTS
Engine Components3 0

Engine & Related Components
pADistributor Cap 2.3L Heavy duty epoxy/resin cap
w/brass terminals.L9B

pBDistributor Rotor 2.3L Heavy duty epoxy/resin rotor
(screw down type 1985-86).
L9F
pB
Distributor Rotor 2.3L Heavy duty epoxy/resin rotor
(push- on type 1987-89).
L9FA
pC
TFI Module 2.3L (Motorcraft)L9M
pD
Distributor 2.3L excludes cap, rotor, module
(35.00 core)
re manufacturedL9AB
pD
Distributor 2.9L excludes cap, rotor, module
(55.00 core)
remanufacturedG9AB
pE
Engine Management XR4Ti and Scorpio engine
management computers. (75.00 core)
remanufactured
XR4TI (specify auto or manual trans) M9C
Scorpio (specify auto or manual trans) G9C
2.3L Turbo Engine Sensors & Switches
pFElectric Fan Switch -XR M450FS
pGKnock Sensor-XR M450KS
pHEngine Coolant Temp Sensor (ECT)-XR M450EC
pIIdle Speed (Air Bypass Valve) XR/Scorpio
M450IS
pJThrottle Position Sensor (TPS)-XR M450TP
pKOxygen Sensor (OS)-XR M450OS
pLOil Pressure Switch-XR M450P
pM
Water Temp Gauge Sender- XR (purple band)M450F
Sensors & Switches (other)
Air Charge Temp. Sensor (ACT) Scorpio G450A
Coolant Temp. Sensor (ECT)- Scorpio M450EC
MAP Sensor -Scorpio G450M
Oil Pressure Switch- Scorpio G450P
Oxygen Sensor- Scorpio G450OS
Vehicle Speed Sensor- Scorpio G450S
Throttle Position Sensor- Scorpio G450TP
pCpB pA
pD
pN
pE
pNA/C Compressor XR4/Scorpio Nippondenso A/C
compressor units, includes clutch.
remanufacturedM470C
pO
Alternator Bosch (90 amp) alternators available for XR &
Scorpio. (10.00 core)
remanufactured.
Alternator -XR4TiM24A
Alternator -ScorpioG24A
pPStarter XR4Ti and Scorpio starter units. (30.00 core) re
manufactured.
Starter -XR4TiM23A
Starter -ScorpioG23A
pQFuel Injectors Replacement injectors for XR4Ti.
35 lb. Standard Brown Top Injector (reman) M7G
35 lb. Optional Disk Type Injector (new) L7G
pRVane Air Meter Larger 50mm (T-bird) and 65mm (SVO)
VAM's can be fitted as a performance upgrade on the XR4Ti.
("PE"
computer chip upgrade required)
50mm VAM (reman) L7V
65mm VAM (reman)L7VA
Standard VAM XR4Ti (reman)L7VM
pSFuel Pressure Regulator Standard replacement regulator
for XR4Ti.M7PR
pTElectric Fuel Pumps New XR4Ti (in line) high pressure
and (in tank) low pressure fuel pumps
Electric Fuel Pump (in line) high pressureM10A
Electric Fuel Pump (in tank) low pressureM10AT
Important note: all electrical items are pre-
tested before shipping. Carefully check all
wiring, fuses & relays
before ordering. Electrical
items are not returnable !
pF pGpHpI
pJ
pK
pL
pM
pO
pQpP
pS
pT
pR
3 1

ABEFG
HIFJK
L
N
O
YZ
GG
The Ford Type 9 (T9) or Hummer transmission is a 5-speed version/
conversion (an overdrive portion is added in a casting extension
behind the main case) of the venerable Type E 4-speed. The only
problem with this transmission is the 2.3 turbo engine's torque output
is near the top of T9's performance envelope. It would seem that
Ford's choice of manual and automatic transmissions were both
marginal at best for use in the XR4Ti. Even so the T9 can give better
than average service when driven sensibly. However, they do not
fair well when abused! A sure sign of problems is a "growling" input
shaft bearing. The sooner this is attended to the better. When the
input bearing fails it will take with it some, or all, of the gearing making
for an expensive repair bill. We can supply individual T9 replacement
parts from this list as requested.pNSyncronizer Ring- 1st/2nd gear M711$33.25
pO
Blocker Spring- syncronizer Z61547.55c
pP
Mainshaft w/Reverse- mainshaft w/reverse gear$308.25
pQ
Gear- 1st gear $172.79
pR
Spacer- oil scoop ring $3.50
pS
Bearing- shaft roller bearing M705$38.35
pT
Circlip- specify thickness size below$4.05
2.42, 2.48, 2.54, 2.61, 2.67mm
pU
Snap Ring- specify size below M705A.85c
1.75, 1.81, 1.87, 1.93, 1.99mm
pV
Gear- 5th driven gear $214.00
pW
Spacer- oil scoop ring $1.20
pX
Blocker Spring- syncronizer Z60785.69c
pY
Syncro Hub- 5th gear syncro hub assembly $129.50
pZ
Syncronizer Ring- 5th gear M713$26.15
pAA
Syncronizer Hub- 5th gear syncro hub $129.50
pBB
Bearing- roller bearing (1987 and up) M707$18.10
pBB
Bearing- 19mm needle (85-87) 21 required M707N$1.89
Spacer/Washer- (1985-87) 2 to 4 required M707S$1.50
pCCGear Cluster- countershaft gear cluster $379.65
pDD
Bearing- roller ball bearing M706$34.50
pEE
Circlip- specify thickness size below$2.00
1.88, 1.95, 2.12, 2.19, 2.25mm
pFF
Gear- 5th driver gear $184.25
pGG
Nut- countershaft nut (12 sided) M706N$4.35
pHH
Countershaft- shaft only Z61892$60.50
pI I
Gear- reverse idler gear $153.20
pJJ
Bushing- reverse idler bush $5.00
pKKIdler Shaft- shaft for reverse idler gear $30.50
FF
KK
JJ
II DD
EE
DD UVWAA
*see page 26 for transmission gaskets & seals
CC
HH Q
N
BBOPU
(early)
87> roller bearing assembly (1 piece)
(late)
G
D
C
M
RSTXX
pASnap Ring- front input shaft (large) M701$2.00
pB
Circlip- front input shaft (small) M701A$2.00
specify size 2.16, 2.24, 2.33, 2.42, 2.50mm
pC
Bearing- input shaft roller bearing M702$29.50
pD
Input Shaft- for XR4Ti $255.00
for Scorpio $220.75
pE
Bearing- rear input needle cage M704$7.15
pF
Syncronizer Ring- 3rd/4th gear syncro M712$26.15
pG
Blocker Spring- syncronizer Z60784.35c
pH
Snap Ring- specify size below M704A$2.00
1.63, 1.74, 1.85mm
pI
Syncronizer Assembly- 3rd/4th gear syncro unit $226.30
pJ
Gear- 3rd gear $149.30
pK
Thrust Ring- retainer 3rd gear $2.00
pLThrust Washer- thrust washer 1/2 Z61144$2.72ea.
pMGear- 2rd gear $155.00
Transmission Components3 3