adjusting screw turns freely in lever.
2) Using torque wrench, tighten band adjusting screw to 30
INCH lbs. (3.5 N.m). Back off adjusting screw 6 turns. Hold adjusting
screw in this position, and tighten lock nut to 25 ft. lbs. (34 N.m).
3) Reinstall oil pan using new gasket. Tighten pan bolts to
150 INCH lbs. (17 N.m). Refill with specified transmission fluid.
KICKDOWN SERVO
ECLIPSE, GALANT, MIRAGE, PRECIS & 3000GT
1) Remove all dirt and grease around kickdown servo switch.
Remove snap ring and kickdown servo switch.
2) To prevent servo piston from turning, install Adapter
(MD998915) and Kickdown Servo Wrench (MD998914) so tab of wrench
engages with notch of piston. See Fig. 2.
CAUTION: DO NOT push servo piston inward while installing adapter
and servo wrench. Install adapter in brake pressure port by
hand ONLY. DO NOT use wrench to tighten adapter.
Fig. 2: Adjusting Kickdown Servo (Except Montero & Pickup)
Courtesy of Mitsubishi Motor Sales of America.
3) Loosen lock nut to "V" channel of adjuster rod. See
Fig. 2 . Tighten inner section of Kickdown Service Adjustment Assembly
(MD998916) until it contacts lock nut.
4) Install outer section of kickdown service adjustment
assembly on lock nut. Rotate outer section to left and inner section
to right to contact lock nut with inner section.
5) Using an INCH lb. torque wrench on inner section, tighten
inner section to 86 INCH lbs. (9.8 N.m), and then loosen inner
section. Tighten inner section to 43 INCH lbs. (4.9 N.m).
CAUTION: Before tightening lock nut with torque wrench, tighten it
by hand until it contacts piston. If torque wrench is used
Check transaxle/transmission and transfer case fluid level
every 30,000 miles. Change fluid at 30,000 miles if operated under
severe service conditions.
CHECKING FLUID LEVEL
TRANSAXLE/TRANSMISSION
Lubricant level is checked at fill hole on side of transaxle
or transmission. Lubricant must be at bottom of fill hole.
TRANSFER CASE
Transfer case contains separate drain and fill plugs.
Lubricant must reach to bottom of fill hole.
On 3000GT models, transfer case contains separate drain and
fill plugs. Lubricant should be .5" (13 mm) from bottom of fill hole.
RECOMMENDED FLUID
Use API GL-4 or GL-5 SAE 75W-85 gear oil.
FLUID CAPACITY SPECS TABLE
TRANSMISSION REFILL CAPACITIES TABLE \
\
\
\
\
Application Pts. (L)
Eclipse
F5M22 .............................. 3.8 (1.8)
F5M33 .............................. 4.7 (2.2)
Galant ............................... 3.8 (1.8)
Mirage
KM201 .............................. 3.8 (1.8)
KM210 .............................. 4.4 (2.0)
Montero
2.6L ............................... 4.7 (2.2)
3.0L ............................... 5.3 (2.6)
Pickup
2WD ................................ 4.9 (2.4)
4WD ................................ 4.7 (2.2)
Precis ............................... 4.4 (2.0)
Sigma ................................ 5.2 (2.5)
\
\
\
\
\
1991 TRANSMISSION REFILL CAPACITIES \
\
\
\
\
\
Application Pts. (L)
Mirage (1.5L)
F4M21 ................................... 3.6 (1.7)
F5M21 ................................... 3.8 (1.8)
Eclipse, Galant (2WD) & Mirage (1.6L) ..... 3.8 (1.8)
Eclipse (Turbo) & 3000GT (2WD) ............ 4.9 (2.3)
Galant (AWD) .............................. 4.9 (2.3)
Montero & Pickup .......................... 5.2 (2.5)
Pickup .................................... 4.9 (2.3)
Pickup .................................... 4.6 (2.2)
Precis
