1991 MITSUBISHI 3000GT sensor

35-92SERVICE BRAKES - G Sensor (AWD - ABS)
G SENSOR (AWD
- ABS)
REMOVALINSTALLATION
Pre-removal and Post-installation OperationRemoval and installation of Front
(Refer to Group 52A - Console Box.)
M35OA-C5Nm
4 ft.lbs.Removal steps
1. G sensor connector
2. G sensor
3. G sensor bracket14FO115
114A019)14A0195
14A0196I
INSPECTIONM350CAD1. INSPECTION OF G SENSOR
(I) Lay the G sensor on a level surface and check for
continuity between its terminals.
(2) Incline the G sensor toward the vehicle front gradually
and check that continuity is lost at an angle of 30” or
more.(3) Incline the G sensor toward the vehicle rear gradually
and check that continuity is lost at an angle of 30” or
more.TSB Revision

36-1
PARKING
BRAKES
CONTENTSM36AA-.
PARKINGBRAKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8SPECIAL TOOLS . .._.._.............................................
PARKING BRAKE LEVER AND PARKINGSPECIFICATIONS................................................
BRAKE CABLE*....................................................5General Specifications....................................
SERVICE ADJUSTMENT PROCEDURES4Lubricants....................................................................Parking Brake Lever Stroke Check4Sealants
andAdhesives....................................................Parking Brake Switch Check
............................4Service Specifications....................................
TROUBLESHOOTING........................................
i
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.
u
I

36-2PARKING BRAKES - Specifications
SPECIFICATIONSM36CA- -
GENERAL SPECIFICATIONS
ItemsSpecifications
iI”
Parking brakes
Type
Brake lever type
Cable arrangementMechanical brake acting on rear wheels
Lever type
V-type
SERVICE SPECIFICATIONSM36cB-.
Items
Standard value
Parking brake lever stroke
Brake lining thicknessmm (in.)
Brake drum I.D.mm (in.)
Clearance between th;$;;d) sensor pole pieceand the rotor tooth
Limit
Brake lining thicknessmm (in.)
Brake drum I.D.mm (in.)
Specifications
3 - 5 notches2.8
(.I 1)
168.0 (6.6)0.2
- 0.7 LOO8 - .028)
1 .o f.039)
169.0 (6.7)
LUBRICANTSM36CD- -
ditems
Rear brake shoe and backing plate contact surfaces
Contact surface between shoe & lining assembly’sstrut and adjusterSpecified lubricant
Brake grease SAE J310, NLGI No. 1
Contact surface between shoe & lining assembly and
shoe-adjustment bolt and shoe-support piece
SEALANTS AND ADHESIVES
ItemsSpecified sealant
Shoe hold-down pin installation surface3M ATD Part No. 8513 or equivalent
1 TSB Revision

36-6PARKING BRAKES - Parking Brake Lever and Parking Brake CableI
50-60 Nm36 - 43 ft.lbs.
Parking brake cable removal
steDs11. Shoe hold-down pin.
1. Cable adjuster** 12. Adjuster
l * l *6. Rear speed sensorl a 13. Shoe-to-anchor spring
(Refer to GROUP 35 -Speed Sensor.)14. Strut
7. Rear brake assembly15. Strut return spring
8. Rear brake disc16. Shoe & lining assembly*-I PI’.
9. Adjusting wheel spring10. Shoe hold-down cupI
/. Llrp18. Parking cable protector19. Parking brake cable16
I
I
I
I
I\
‘d ~
14FOO70TSB Revision

36-8PARKING BRAKES - Parking Brake
PARKING BRAKE
REMOVAL AND INSTALLATION
{emoval steps1’
C* l *1. Rear speed sensor
3. Rear brake assembly
4. Rear brake disc
5.Hubcap
l +6. Flange nut7.Washer
8. Rear hub unit
beanng12. Adjusting wheel spring
13. Shoe hold-down cup
14. Shoe hold-down spring
15. Shoe hold-down pin
l * 16. Adjusterl a 17. Shoe-to-anchor spring18.Strut
19. Strut return spring
20. Shoe
& lining assembly21.Clip23.Backingplate
71
Adjustment (Refer to P.36.4.)
83 Nm60ft.lbS. 50-60Nm
36 - 43 ft.lbs.
/
M36YA- -
Sealant: 3M ATD Part No.
8513 or equivalent50-60 Nm
36 - 43 ftlbs.
14NOOll
L23
20
*
14N0004
Grease: Brake grease SAE J310, NLGI No. 1
14LOO15c:&14D650
d,
I
ITSB Revision

PARKING BRAKES - Parking Brake36-9
4WD>
190Nm
137ft.lbs.
83Nm12 Nm60ft.lbs.9 ft.lbs.50-60
Nm36 43-ft.lbs.Removal steps
+*I. Rear speed sensor2. O-ring
3. Rear brake assembly
4. Rear brake disc
50-60Nm36 - 43 ft.lbs.l * l *9. Self-locking nut10. Companion flangel *11. Rear axle shaft
12. Adjusting wheel spring
13. Shoe hold-down
CUD14. Shoe hold-down spnng15. Shoe hold-down pinI)* 16. AdjusterI)* 17. Shoe-to-anchor spring
18. Strut
19. Strut return spring
20. Shoe
& lining assembly
21. Clip
22. Brake tube connection
23. Backing plate23
Grease: Brake grease SAE 5310, NLGI No. 1
1 TSB Revision1

36-10PARKING BRAKES - Parking Brake
SERVICE POINTS OF REMOVALM36YBALI. REMOVAL OF REAR SPEED SENSOR
Caution
When removing the speed sensor from the knuckle, usei&J 1
care not to hit the pole piece at its tip against the rotorteeth or other parts.
11 FO03814LOOOi
14NOli9. REMOVAL OF SELF-LOCKING NUT
With the special tool, secure the axle shaft and remove the
companion flange self-locking nut.
II. REMOVAL OF AXLE SHAFT ASSEMBLY
With the special tool, remove the axle shaft from the trailing
arm.
INSPECTIONM36YCAI
CHECKING FOR UNUSUAL WEAR OF THE BRAKE LININGAND BRAKE DRUM
(1) Measure the thickness of the brake lining at several places.
Standard value: 2.8 mm
(.I10 in.)
Limit:
1.0 mm (.039 in.)
Caution
Replace the brake shoes if the thickness of the brakelining is the limit value or less.
(2)Measure the brake disc drum inner diameter at two or more
places.Standard value: 168.0 mm (6.6 in.)
Limit: 169.0 mm (6.7 in.)
CautionReplace if the brake disc drum inner diameter is the
limit value or more.
TSB Revision

PARKING BRAKES - Parking Brake36-11
14N000'
Spindle,
I’_14NOO05
SERVICE POINTS OF INSTALLATIONM36YDAP
17. INSTALLATION OF SHOE-TO-ANCHOR SPRINGThe shoe-to-anchor spring must be installed in the se-
quence shown in the illustration.
Caution
Each shoe-to-anchor spring has a unique spring loadand the spring “a”is painted to prevent erroneous
installation.
NOTEThe figure shows the left wheel; for the right wheel, the
position in symmetrical.
16. INSTALLATION OF ADJUSTERInstall the adjuster facing the left adjusting bolt to the
vehicle front and right adjusting bolt to the vehicle rear.
9. INSTALLATION OF SELF-LOCKING NUT
With the special tool, secure the axle shaft and tighten the
companion flange self-locking nut.
6. INSTALLATION OF FLANGE NUT
After tightening the flange nut, align with the spindle’s
indentation and crimp.
1. INSTALLATION OF REAR SPEED SENSOR
Insert a filler gauge between the speed sensor pole piece
and rotor teeth and tighten the speed sensor at such
position where the gap is as specified below over the entire
circumference.
Standard value: 0.2
- 0.7 mm (.008 - .028 in.)
TSB Revision