Page 162 of 392
Fig. 9: Testing ANTI-LOCK Warning Light (RX7)
Courtesy of MAZDA MOTORS CORP.
1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 10 © 2005 Mitchell Repair Information Company, LLC.
Page 163 of 392

Fig. 10: Testing ANTI-LOCK Warning Light (929)
Courtesy of MAZDA MOTORS CORP.
STOPLIGHT SWITCH
Continuity Test
Disconnect stoplight switch connector. Using a DVOM, check continuity between Green or Green/White wire
and White/Green wire with brake pedal depressed. Ensure continuity exists. Release pedal, and note reading on
DVOM. Continuity should not be present. If continuity is not as specified, replace switch.
FRONT & REAR VALVES
Resistance Test (Miata)
1. Disconnect hydraulic unit 12-pin connector. Using a DVOM, measure resistance between the following
wires: Yellow/Green wire and Black wire; Brown wire and Black wire; Black/White wire and Black wire.
Resistance should be 1-1.2 ohms in each measurement.
2. If resistance is not as specified, replace hydraulic unit. If resistance is as specified, check wiring harness
between ABS control unit and hydraulic unit.
Resistance Test (RX7 & 929)
1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 11 © 2005 Mitchell Repair Information Company, LLC.
Page 209 of 392

engagement while rotating adjusting screw to prevent burring screw slots. Ensure adjusting screw rotates
freely.
PARKING BRAKE
B2200 & B2600i
1. Depress brake pedal several times while vehicle is moving in Reverse. Ensure brakes are properly
adjusted. Pull parking brake lever with a force of 44 lbs. (20 kg). If stroke is 7-12 notches, parking brake
is properly adjusted.
2. If stroke is not 7-12 notches, raise and support rear of vehicle. Release parking brake lever. Loosen cable
lock nut at lever end of cable. Rotate adjusting nut until correct stroke is obtained. Operate parking brake
several times and ensure rear wheels rotate freely. Ensure parking brake warning light illuminates when
brake lever is pulled one notch.
Navajo
1. Adjust service brakes before adjusting parking brake cable. Ensure brake drums are cold. Apply parking
brake to fully depressed position. Grip threaded rod to prevent it from spinning.
2. Thread equalizer nut 6 full turns past its original position on threaded rod. See Fig. 4
. Check cable
tension at rear of equalizer assembly using Cable Tension Gauge (021-00018). If tension is not 400-600
lbs. (182-272 k
g), repeat step 2).
1991 Mazda MX-5 Miata
BRAKE SYSTEM 1991 BRAKES Mazda Brake System
Microsoft
Sunday, July 05, 2009 2:18:08 PMPage 6 © 2005 Mitchell Repair Information Company, LLC.
Page 211 of 392

2. Release parking brake lever. Using a screwdriver, reach through parking brake handle hole in console and
rotate adjusting screw until stroke is 6-8 notches. Ensure rear wheels rotate freely. Ensure parking brake
warning light illuminates when brake lever is pulled one notch.
Miata, MX-6, MPV, Protege, RX7, 323, 626
1. On models with rear disc brakes, depress brake pedal several times. On models with rear drum brakes,
start engine and depress brake pedal several times while vehicle is moving in Reverse. Stop engine.
2. On all models, pull parking brake lever with a force of 22 lbs. (10 kg). If stroke is 5-7 notches, parking
brake is properly adjusted. If stroke is not 5-7 notches, raise and support rear of vehicle. Release parking
brake lever.
3. Rotate cable adjusting nut at lever end of cable (under console cover) until stroke is within specification.
On models equipped with rear disc brakes, ensure clearance between stopper and lever (at each caliper) is
not less than .08" (2 mm) on RX7, or zero on all other models. On all models, ensure parking brake
warning light illuminates when brake lever is pulled one notch.
PARKING BRAKE SHOES
929
Raise and support vehicle. Remove rear wheels. Remove service plug from rotor. Using a screwdriver, rotate
star wheel adjuster toward axle until rotor locks. Rotate adjuster in opposite direction 3-5 notches. Ensure rotors
turn freely and parking brake functions properly. Install service plug and rear wheels.
PEDAL FREE PLAY
Depress pedal a few times to eliminate vacuum. Pedal free play should be .16-.28" (4-7 mm). Adjust play by
loosening push rod lock nut. Turn push rod until correct free play is obtained. Tighten push rod lock nut.
PEDAL HEIGHT & STOPLIGHT SWITCH
1. Released pedal height is measured from carpet surface on vertical portion of firewall to pedal pad center.
Disconnect stoplight switch electrical connector. Loosen lock nut on stoplight switch. Move switch away
from pedal. Loosen push rod lock nut. Turn rod until correct pedal height is obtained. See BRAKE
PEDAL HEIGHT SPECIFICATIONS .
2. Adjust pedal free play. See PEDAL FREE PLAY
under ADJUSTMENTS. Tighten push rod lock nut.
Rotate stoplight switch until it contacts pedal and then rotate an additional 1/2 turn. Tighten stoplight
switch lock nut. Reconnect stoplight switch electrical connector.
3. Applied pedal height is measured from angled portion of firewall (without carpet) to pedal pad center.
Start engine. On B2200, B2600i and MPV, depress brake pedal with 33 lbs. (15 kg) pressure. On all other
models, depress brake pedal with 132 lbs. (60 k
g) pressure. tension should be checked and adjusted.
NOTE: Pedal height and stoplight switch information is not available for Navajo.
1991 Mazda MX-5 Miata
BRAKE SYSTEM 1991 BRAKES Mazda Brake System
Microsoft
Sunday, July 05, 2009 2:18:08 PMPage 8 © 2005 Mitchell Repair Information Company, LLC.
Page 247 of 392

CHARGING SYSTEM TROUBLE SHOOTING
TROUBLE SHOOTING PRECAUTIONS
Miata
Obtain code number and deactivate audio anti-theft system before disconnecting battery.
All Models
DO NOT reverse battery cable connections. Rectifier will be damaged.
DO NOT use high voltage type testers.
PROBLEM Possible CauseAction
NO START CONDITION
Dead BatteryCheck/Replace Battery
Bad Cable ConnectionsClean/Replace Cables
Ignition Switch/Circuit FaultCheck Switch/Circuit
CHARGING SYSTEM WARNING LIGHT STAYS ON
Loose/Worn Alternator BeltTighten/Replace Belt
Loose Alternator ConnectionsCheck/Repair
Connections
Warning Light WiringCheck/Repair Wiring
Faulty Stator/DiodesTest/Repair Alternator
Faulty Voltage RegulatorTest/Repair Regulator
WARNING LIGHT OFF WITH IGNITION SWITCH ON
Blown FuseCheck/Replace Fuse
Faulty AlternatorTest Alternator
Bad Warning Light BulbTest/Replace Bulb
WARNING LIGHT ON WITH IGNITION SWITCH OFF
Alternator Wiring ShortCheck/Repair Wiring
Faulty Rectifier BridgeTest/Repair Alternator
AMMETER INDICATES DISCHARGE
Loose/Worn Alternator BeltTighten/Replace Belt
Loose Alternator ConnectionsCheck/Repair
Connections
Faulty AmmeterTest/Replace Ammeter
NOISY Defective BatteryReplace Battery
Defective AlternatorTest/Repair Alternator
Defective RegulatorTest/Repair Regulator
NOTE: Observe the following precautions when trouble shooting or testing charging
system:
1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 3 © 2005 Mitchell Repair Information Company, LLC.
Page 314 of 392

FUSES & CIRCUIT BREAKERS
Fuses & Circuit Breakers 1990-95 Mazda
FUSES & CIRCUIT BREAKERS
FUSE PANEL LOCATION
Fuse box is located above driver's left knee, accessible through a removable cover. The main fuse block is
located at the right rear of the engine compartment.
The Trunk Mounted Fuse Panel is located on the right side of the trunk, near the trunk hinge. (1992-95 Models)
MAIN FUSE BLOCK IDENTIFICATION
Fig. 1: Main Fuse Block Identification
Courtesy of MAZDA MOTOR OF AMERICA, INC.
Fuse & Circuit Breaker Identification
WARNING:Always disconnect battery ground cable before servicing "high-current"
fuses. It is recommended that "high-current" fuses be replaced by a
qualified technician.
1991 Mazda MX-5 Miata
FUSES & CIRCUIT BREAKERS Fuses & Circuit Breakers 1990-95 Mazda
1991 Mazda MX-5 Miata
FUSES & CIRCUIT BREAKERS Fuses & Circuit Breakers 1990-95 Mazda
Microsoft
Sunday, July 05, 2009 2:15:54 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 2:15:57 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Page 315 of 392
1 - 30 Amp (Pink) Headlights
2 - 30 Amp (Pink) Fuel Injection, Alternator
3 - 80 Amp (Black) Protection Of All Circuits
4 - 40 Amp (Green) Taillights, Shift Lock, Cruise Control, Horn, Stoplights, Hazard Warning Lights,
Interior Lights, Warning Buzzers, Radio/Cassette, Compact Disc Player, Clock
5 - Empty (1990); 60 Amp (Yellow) (1991-94) Anti-Lock Brake System
6 - 30 Amp (Pink) Cooling Fan
7 - 10 Amp (Red) Air Bag
8 - 20 Amp (Yellow) A/C Additional Fan
9 - 10 Amp (Red) Fuel Injection
10 - 30 Amp (Pink) Headlight Retractor
TRUNK MOUNTED FUSE PANEL IDENTIFICATION
1991 Mazda MX-5 Miata
FUSES & CIRCUIT BREAKERS Fuses & Circuit Breakers 1990-95 Mazda
Microsoft
Sunday, July 05, 2009 2:15:54 PMPage 2 © 2005 Mitchell Repair Information Company, LLC.
Page 317 of 392
Fig. 3: Interior Fuse Panel Identification
Courtesy of MAZDA MOTOR OF AMERICA, INC.
Fuse & Circuit Breaker Identification
11 - 15 Amp (Blue) Engine Cooling Fan
12 - 10 Amp (Red) Gauges, Warning Lights, Turn Signal Lights, Cruise Control
13 - 15 Amp (Blue) Air Bag
14 - 30 Amp Heater
15 - Empty
16 - 30 Amp (Green) Power Windows
17 - 20 Amp (Yellow) Wipers, Washers
18 - Empty
19 - 15 Amp (Blue) Taillights
20 - Empty
21 - 15 Amp (Blue) Shift Lock, Cruise Control, Horn, Stoplights
22 - 15 Amp (Blue) Hazard Warning Lights
1991 Mazda MX-5 Miata
FUSES & CIRCUIT BREAKERS Fuses & Circuit Breakers 1990-95 Mazda
Microsoft
Sunday, July 05, 2009 2:15:54 PMPage 4 © 2005 Mitchell Repair Information Company, LLC.