1991 MAZDA MIATA lock

ABS DIODE
Continuity Test
1. Unplug hydraulic unit 12-pin connector. On Miata, connect positive lead of DVOM to Blue/Yellow wire
terminal and negative lead to Gray wire terminal of hydraulic unit. On RX7, connect positive lead of
DVOM to Red wire terminal and negative lead to Yellow/Red wire terminal of hydraulic unit.
2. On 929, connect positive lead of DVOM to Violet wire terminal and negative lead to Yellow/Red wire
terminal of hydraulic unit. Ensure continuity is present between terminals. Reverse DVOM leads.
Continuity should not be present with leads reversed. If ABS diode does not test as described, replace
ABS diode.
ABS SYSTEM GROUND
Continuity Test (Miata)
Using a DVOM, check for continuity between terminals "D", "S", and "f" of control unit harness connector and
ground. See Fig. 4
or Fig. 5 . If continuity is not present, repair harness.
Continuity Test (RX7 & 929)
Use DVOM to check continuity. ON RX7, check between control unit harness connector terminal "D" and JC-
02 connector. See Fig. 4
and Fig. 6 or Fig. 5 and Fig. 7 . On 929, check between control unit harness connector
terminal "T" and JC-02 connector. If continuity is not present, repair harness.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 5 © 2005 Mitchell Repair Information Company, LLC.

Fig. 4: Identifying Control Unit Harness Connector Terminals
Courtesy of MAZDA MOTORS CORP.
Fig. 5: Identifying Control Unit Harness Connector Terminals

Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 6 © 2005 Mitchell Repair Information Company, LLC.

Fig. 6: Locating JC-02 Connector
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 7 © 2005 Mitchell Repair Information Company, LLC.

Fig. 7: Locating JC-02 Connector
Courtesy of MAZDA MOTORS CORP.
ANTI-LOCK WARNING LIGHT
Operational Test (Miata)
1. Start engine, and observe ANTI-LOCK light. Light should illuminate for a few seconds. If light does not
illuminate as described, remove instrument cluster. Connect 12 volts to terminal 2k of instrument cluster.
See Fig. 8
. Using a jumper wire, connect terminal 1K of instrument cluster to ground. ANTI-LOCK light
should illuminate. If light does not illuminate, check bulb. If bulb is okay, check meter fuse and wiring
harness.
2. Install instrument cluster, and recheck warning light operation. If light still does not illuminate for a few
seconds, check wiring harness between ANTI-LOCK light and control unit and between ANTI-LOCK
light and hydraulic unit. Check operation of hydraulic unit valve relay.
Operational Test (RX7)

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 8 © 2005 Mitchell Repair Information Company, LLC.

1. Start engine, and observe ANTI-LOCK light. Light should illuminate for a few seconds. If light does not
illuminate as described, remove clock and bezel assembly from dashboard. Slide warning and clock unit
from instrument panel. Connect terminal "E" to ground. See Fig. 9
. ANTI-LOCK light should illuminate.
If light does not illuminate, check bulb. If bulb is okay, check meter fuse and wiring harness.
2. Install instrument cluster, and recheck warning light operation. If light still does not illuminate for a few
seconds, check wiring harness between ANTI-LOCK light and control unit, and ANTI-LOCK light and
hydraulic unit. Check operation of hydraulic unit valve relay.
Operational Test (929)
1. Start engine, and observe ANTI-LOCK light. Light should illuminate for a few seconds. If light does not
illuminate as described, remove instrument cluster. Connect 12 volts to terminal "J" of instrument cluster
connector I-06. See Fig. 10
. Using a jumper wire, connect terminal "E" of instrument cluster connector I-
08 to negative ground. ANTI-LOCK light should illuminate. If light does not illuminate, check bulb. If
bulb is okay, check meter fuse and wiring harness.
2. Install instrument cluster, and recheck warning light operation. If light still does not illuminate for a few
seconds, check wiring harness between ANTI-LOCK light and control unit and between ANTI-LOCK
light and hydraulic unit. Check operation of hydraulic unit valve relay.
Fig. 8: Testing ANTI
-LOCK Warning Light (Miata)
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 9 © 2005 Mitchell Repair Information Company, LLC.

Fig. 9: Testing ANTI-LOCK Warning Light (RX7)
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 10 © 2005 Mitchell Repair Information Company, LLC.

Fig. 10: Testing ANTI-LOCK Warning Light (929)
Courtesy of MAZDA MOTORS CORP.
STOPLIGHT SWITCH
Continuity Test
Disconnect stoplight switch connector. Using a DVOM, check continuity between Green or Green/White wire
and White/Green wire with brake pedal depressed. Ensure continuity exists. Release pedal, and note reading on
DVOM. Continuity should not be present. If continuity is not as specified, replace switch.
FRONT & REAR VALVES
Resistance Test (Miata)
1. Disconnect hydraulic unit 12-pin connector. Using a DVOM, measure resistance between the following
wires: Yellow/Green wire and Black wire; Brown wire and Black wire; Black/White wire and Black wire.
Resistance should be 1-1.2 ohms in each measurement.
2. If resistance is not as specified, replace hydraulic unit. If resistance is as specified, check wiring harness
between ABS control unit and hydraulic unit.
Resistance Test (RX7 & 929)

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 11 © 2005 Mitchell Repair Information Company, LLC.

1. Disconnect hydraulic unit 12-pin connector. Using a DVOM, measure resistance between Green/Black
and Yellow/Red wires, Green/White and Yellow/Red wires and Yellow and Yellow/Red wires.
Resistance should be 1-1.2 ohms in each measurement.
2. If resistance if not as specified, replace hydraulic unit. If resistance is as specified, check wiring harness
between ABS control unit and hydraulic unit.
HYDRAULIC UNIT
Only serviceable parts of hydraulic unit are motor relay and valve relay. If other parts of unit malfunction,
replace hydraulic unit assembly.
MOTOR RELAY
Continuity Tests
1. Disconnect negative battery cable. Remove motor relay from hydraulic unit. Ensure continuity exists
between terminals "B" and "C" of motor relay. See Fig. 11
. Connect 12 volts to terminal "C", and ground
terminal "B". Ensure continuity exists between terminals "A" and "D".
2. Replace relay if continuity is not as specified. If continuity is as specified, check wiring harness between
motor relay and ABS control unit fuse (60 amps).
Fig. 11: Identifying Motor & Valve Relay Terminals

Courtesy of MAZDA MOTORS CORP.
PUMP MOTOR
Continuity Test (Miata)

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 12 © 2005 Mitchell Repair Information Company, LLC.