1991 MAZDA MIATA relay

Disconnect 2-pin connector at hydraulic unit. Check continuity at hydraulic control between Red/Yellow wire
terminal and ground. If continuity is not present, replace hydraulic control unit. If continuity is present, pump is
okay. Check wiring between hydraulic control and ABS control unit.
Continuity Test (RX7 & 929)
1. Disconnect 12-pin hydraulic unit connector. Using a DVOM, check continuity between Black wire and
ground. If there is continuity, check continuity between Black wire terminal at hydraulic unit connector
and Green wire terminal at 2-pin hydraulic unit connector.
2. If continuity exists, connect hydraulic unit connectors. If continuity is not present, replace wiring harness
between control unit and body ground.
3. Disconnect ABS control unit connector. Check continuity between Green wire of ABS control unit
harness connector and ground. If continuity is present, check for poor connection of ABS control unit
connector or faulty ABS control unit. If continuity is not present, repair open circuit.
VALVE RELAY
Continuity Tests
1. Disconnect negative battery cable. Remove valve relay from hydraulic unit. Using a DVOM, check
continuity between relay terminals "C" and "E" and between terminals "B" and "D". See Fig. 11
.
2. Ensure continuity exists. Connect 12 volts to terminal "B", and ground terminal "D". Check continuity
between terminals "A" and "E". Ensure continuity exists. If continuity is not as specified, replace valve
relay.
WHEEL SPEED SENSORS
Sensor Resistance Test
Disconnect speed sensor connector. Using a DVOM, measure resistance between sensor terminals. Resistance
should be 800-1200 ohms. If resistance is not as specified, replace speed sensor.
Harness Continuity & Voltage Tests
1. With ignition off and speed sensors connected, disconnect ABS control unit connector. Using a DVOM,
check continuity between indicated terminals of ABS control unit harness connector. See WHEEL
SPEED SENSOR TESTS TABLE.
2. If reading on DVOM is not 800-1200 ohms, check wiring harness between wheel speed sensor and ABS
control unit. If DVOM reading is 800-1200 ohms, check voltage between indicated terminals in WHEEL
SPEED SENSOR TESTS TABLE.
3. Turn ignition on. Rotate appropriate wheel one revolution per second by hand to check voltage. If DVOM
does not indicate 50-60 millivolts, replace wheel speed sensor.
WHEEL SPEED SENSOR TESTS
Test Between Control Unit

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:32 PMPage 13 © 2005 Mitchell Repair Information Company, LLC.

ELECTRICAL COMPONENT LOCATOR
1991 MAZDA ELECTRICAL COMPONENTS
BUZZERS, RELAYS & TIMERS
BUZZERS, RELAYS & TIMERS LOCATION
CIRCUIT PROTECTION DEVICES
CIRCUIT PROTECTION DEVICES LOCATION
CONTROL UNITS
ComponentLocation
ABS System
Check Valve RelayOn top of ABS pump motor.
Motor RelayOn top of ABS pump motor.
Buzzer & Timer UnitOn bracket, behind left side of dash.
See Fig. 1
.
Circuit Opening RelayOn bracket, behind left side of dash.
See Fig. 1
.
Cooling Fan RelayIn engine compartment fuse/relay
block. See Fig. 1
.
Dashboard Illumination Lights RelayOn bracket, near master cylinder. See
Fig. 1
.
EFI Main RelayIn engine compartment fuse/relay
block. See Fig. 1
& Fig. 2 .
Fuel Pump RelayBehind left front kick panel.
Headlight RelayOn bracket, near master cylinder. See
Fig. 1
.
Headlight Retractor RelayOn bracket, near master cylinder. See
Fig. 1
.
Horn RelayOn bracket, behind left side of dash.
See Fig. 1
.
Ignition RelayIn engine compartment fuse/relay
block.
Turn Signal/Hazard Flasher RelayOn bracket, behind left side of dash.
See Fig. 1
.
ComponentLocation
Fuse BlockBehind left side of dash.
Fuse/Relay BlockIn right rear corner of engine compartment, near firewall.
See Fig. 2
.
Heater Blower Motor Circuit BreakerIn passenger compartment fuse block.

1991 Mazda MX-5 Miata
ELECTRICAL COMPONENT LOCATOR 1991 MAZDA ELECTRICAL COMPONENTS

1991 Mazda MX-5 Miata
ELECTRICAL COMPONENT LOCATOR 1991 MAZDA ELECTRICAL COMPONENTS
Microsoft
Sunday, July 05, 2009 2:15:23 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 2:15:28 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.

SWITCHES
SWITCHES LOCATION
MISCELLANEOUS
MISCELLANEOUS LOCATION
COMPONENT LOCATION GRAPHICS
ComponentLocation
Idle Speed Control SolenoidOn throttle body.
Purge Control Solenoid ValveOn right side of engine compartment, on shock
tower.
ComponentLocation
A/C Pressure SwitchOn high pressure refrigerant line.
Back-Up Light SwitchOn left side of transmission.
Clutch SwitchOn bracket, above clutch pedal. See Fig. 2 .
Neutral SwitchOn right rear side of transmission. See Fig. 2 .
Parking Brake SwitchOn base of parking brake lever.
Power Steering Pressure SwitchOn power steering housing assembly. See Fig. 2 .
Seat Belt Buckle SwitchOn driver's side seat belt buckle.
Stoplight SwitchOn bracket, above brake pedal. See Fig. 2 .
ComponentLocation
Diagnostic Check ConnectorOn left rear of engine compartment, near master cylinder. See Fig. 2 .
IgniterOn right rear corner of engine compartment, near fuse/relay block. See
Fig. 2
.
SRS Back-Up BatteryMounted below SRS control unit. See Fig. 3 .
NOTE: Figures may show multiple component locations. Refer to appropriate table for
proper figure references.

1991 Mazda MX-5 Miata
ELECTRICAL COMPONENT LOCATOR 1991 MAZDA ELECTRICAL COMPONENTS
Microsoft
Sunday, July 05, 2009 2:15:23 PMPage 3 © 2005 Mitchell Repair Information Company, LLC.

HEATER SYSTEM
1990-92 Heater Systems
DESCRIPTION & OPERATION
Heater case, mounted under center of instrument panel, contains airflow mode door and air-mix (temperature
blend) door. See Fig. 1
. Blower case, mounted under right end of instrument panel, contains recirculated/fresh
air door. All doors are controlled manually from control panel by cable.
Blower motor relay, in left rear corner of engine compartment (on relay cluster), supplies power to blower
motor. Blower resistors, on bottom of blower case, determine blower speed.
Fig. 1: Exploded View of Heater Case

Courtesy of MAZDA MOTORS CORP. WARNING:To avoid injury from accidental air bag deployment, read and carefully
follow all SERVICE PRECAUTIONS and DISABLING & ACTIVATING AIR
BAG SYSTEM procedures in AIR BAG article in the
ACCESSORIES/SAFETY EQUIPMENT Section.

1991 Mazda MX-5 Miata
HEATER SYSTEM 1990-92 Heater Systems

1991 Mazda MX-5 Miata
HEATER SYSTEM 1990-92 Heater Systems
Microsoft
Sunday, July 05, 2009 2:12:14 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 2:12:18 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.

A/C-HEATER SYSTEM - MANUAL
1990-92 Manual A/C-Heater Systems
A/C SYSTEM SPECIFICATIONS
A/C SYSTEM SPECIFICATIONS
DESCRIPTION
Blower case, mounted under right end of instrument panel, contains blower motor and fresh/recirculated air
door. Evaporator case, to left of blower case, contains evaporator, evaporator thermoswitch and expansion
valve. Heater case, to left of evaporator case, contains airflow mode door and air-mix (temperature blend) door.
ELECTRICAL COMPONENT LOCATIONS
OPERATION
All air control doors are controlled manually by cable from control panel. Top lever controls the air-mix door,
center lever controls the fresh/recirculated air door and bottom lever controls the airflow mode door.
ApplicationSpecification
Compressor TypeNippondenso Rotary Vane
Compressor Belt Deflection (1) (2)
New5/16-23/64" (8-9 mm)
Used23/64-25/64" (9-10 mm)
Compressor Oil Capacity2.7-3.3 oz.
Refrigerant (R-12) Capacity28 oz.
System Operating Pressures
High Side171-235 psi (12.0-16.5
kg/cm
2 )
Low Side21-43 psi (1.5-3.0 kg/cm2 )
(1)With 22 lbs. (10 kg) pressure applied to center of belt.
(2)On vehicles with P/S, measure midway between crankshaft pulley and P/S pump pulley. On vehicles
without P/S, measure midway between crankshaft pulley and A/C idler pulley.
ComponentLocation
A/C RelayIn Right Front Corner Of Engine Compartment
Blower Motor RelayIn Left Rear Corner Of Engine Compartment
Blower ResistorOn Bottom Of Blower Case
Evaporator Thermoswitch. On Left Side Of Evaporator Case
Pressure SwitchIn High-Pressure Line, Between Receiver-Drier
And Evaporator

1991 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1990-92 Manual A/C-Heater Systems

1991 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1990-92 Manual A/C-Heater Systems
Microsoft
Sunday, July 05, 2009 2:11:52 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 2:11:56 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.

Blower motor relay supplies power to blower motor. Blower resistor determines blower speed. With blower
switch in highest position, blower motor is grounded through blower switch. With blower switch in all other
positions, blower motor is grounded through blower resistor and blower switch.
Circuit through compressor clutch is completed when A/C relay is energized and pressure switch is closed. A/C
relay is energized when Engine Control Unit (ECU) unit grounds the solenoid circuit of the relay. The ECU
energizes A/C relay if evaporator thermoswitch is closed and A/C and blower switches are on. The ECU also
controls A/C relay operation according to engine load.
ADJUSTMENTS
AIRFLOW MODE DOOR
Set airflow mode control lever to vent position. Disconnect control cable at airflow mode door lever. Extend
airflow mode door lever until it stops, and hold it there. See Fig. 1
. Attach control cable to door lever and clip.
Ensure control lever moves freely between defrost and vent positions.
AIR-MIX (TEMPERATURE BLEND) DOOR
Set temperature control lever to maximum hot position. Disconnect control cable at air-mix door lever. See Fig.
1 . Extend air-mix door lever until it stops, and hold it there. Attach control cable to door lever and clip. Ensure
control lever moves freely between hot and cold positions.
RECIRCULATED/FRESH AIR DOOR
Set recirculated/fresh air control lever to fresh position. Disconnect control cable at recirculated/fresh air door
lever. Retract recirculated/fresh air door lever until it stops, and hold it there. Attach control cable to door lever
and clip. Ensure control lever moves freely between recirculated air and fresh air positions.
TESTING
AIR BAG WARNING
BLOWER MOTOR CIRCUIT
1. Check 30-amp HEATER circuit breaker in passenger compartment fuse panel. If Red button has not
popped out, go to next step. If Red button has popped out, repair short circuit and press Red button to
reset circuit breaker.
2. Turn ignition on. Turn blower switch to 4th position (high). Check voltage at Blue wire terminal of 2-
wire blower motor connector on bottom of blower case. If no voltage is present, repair wiring between
circuit breaker and blower motor. WARNING:To avoid injury from accidental air bag deployment, read and carefully
follow all SERVICE PRECAUTIONS and DISABLING & ACTIVATING AIR
BAG SYSTEM procedures in AIR BAG article in the
ACCESSORIES/SAFETY EQUIPMENT Section.

1991 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1990-92 Manual A/C-Heater Systems
Microsoft
Sunday, July 05, 2009 2:11:52 PMPage 2 © 2005 Mitchell Repair Information Company, LLC.

3. If battery voltage is present, turn off blower switch and A/C switch (if equipped). Check voltage at
Blue/Red wire terminal of blower resistor 1-wire connector. If no voltage is present, replace blower
motor. If battery voltage is present, check voltage at Blue/White wire terminal of blower resistor
connector.
4. If no voltage is present, replace blower resistor. If battery voltage is present, check voltage at Blue/Red
wire terminal of blower resistor 4-wire connector. If no voltage is present, replace blower resistor.
5. If battery voltage is present, check voltage at Blue/Green wire terminal of blower resistor connector. If no
voltage is present, replace blower resistor. If battery voltage is present, check voltage at Blue/Yellow wire
terminal of blower resistor connector.
6. If no voltage is present, replace blower resistor. If battery voltage is present, turn ignition on and blower
switch to 4th position (high). Check voltage at Black wire terminal of blower switch connector. If battery
voltage is present, repair wiring between blower switch and ground.
7. If no voltage is present, turn ignition switch, blower switch and A/C switch off. Check voltage at
Blue/White wire terminal of blower switch connector. If no voltage is present, repair wiring between
blower resistor and blower switch.
8. If battery voltage is present, check voltage at Blue/Red wire terminal of blower switch connector. If no
voltage is present, repair wiring between blower resistor and blower switch. If battery voltage is present,
check voltage at Blue/Green wire terminal of blower switch connector.
9. If no voltage is present, repair wiring between blower resistor and blower switch. If battery voltage is
present, check voltage at Blue/Yellow wire terminal of blower switch connector. If battery voltage is
present, replace blower switch. If no voltage is present, repair wiring between blower resistor and blower
switch.
COMPRESSOR CLUTCH CIRCUIT
1. Turn ignition on. Check 20-amp WIPER fuse in passenger compartment fuse block. Check 20-amp AD
FAN (additional fan) fuse in engine compartment fuse block. If fuses are blown, repair short circuit.
2. If fuses are okay, run engine at idle. Turn A/C and blower switches on. Check voltage at compressor
clutch connector (Black/Red wire terminal). If no voltage is present, go to step 5).
3. If battery voltage is present, turn ignition off. Disconnect evaporator thermoswitch connector. Check
continuity between switch terminals. If there is no continuity, replace evaporator thermoswitch.
4. If there is continuity, disconnect compressor clutch connector. Set ohmmeter to X1000 scale. Check
continuity between compressor clutch connector and ground. If there is no continuity, replace compressor
clutch. If there is continuity, adjust compressor clutch air gap or check compressor for internal damage.
5. Run engine at idle. Turn A/C and blower switches on. Check voltage at Black/Blue wire terminal of A/C
relay connector. If battery voltage is present, go to step 9).
6. If no voltage is present, check voltage at Blue/Yellow wire terminal of A/C relay connector. If no voltage
is present, repair circuit between 20-amp AD FAN fuse and A/C relay.
7. If battery voltage is present, check voltage at Blue wire terminal of A/C relay connector. If no voltage is
present, repair circuit between 20-amp WIPER fuse and A/C rela
y. NOTE: Blower resistor uses a 1-wire connector and a 4-wire connector. The wire
in the 1-wire connector is Blue/Red, and one of the wires in the 4-wire
connector is Blue/Red. Check voltage at appropriate wire.

1991 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1990-92 Manual A/C-Heater Systems
Microsoft
Sunday, July 05, 2009 2:11:52 PMPage 3 © 2005 Mitchell Repair Information Company, LLC.

8. If battery voltage is present, check voltage at Blue/Black wire terminal of A/C relay connector. If no
voltage is present, replace A/C relay. If battery voltage is present, check Engine Control Unit (ECU)
terminal voltage.
9. Turn ignition off. Disconnect pressure switch connector. Check continuity between switch terminals. If
there is continuity, repair circuit between A/C relay and compressor clutch.
10. If there is no continuity, connect manifold pressure gauges to system. If low pressure is 21-43 psi (1.5-3.0
kg/cm
2 ) and high pressure is 171-235 psi (12.0-16.5 kg/cm2 ), replace pressure switch. If pressures are
not as specified, check refrigerant system for proper charge.
CONDENSER (ADDITIONAL) FAN CIRCUIT
1. Turn ignition on. Turn A/C and blower switches on. Check voltage at Black/Blue wire terminal of
condenser fan connector. If no voltage is present, repair circuit between A/C relay and condenser fan.
2. If battery voltage is present, check voltage at Black wire terminal of condenser fan connector. If no
voltage is present, replace condenser fan motor. If battery voltage is present, repair circuit between
condenser fan and ground.
A/C & BLOWER SWITCH
With switches in positions indicated, check continuity between specified terminals of A/C and blower switch
connector. See Fig. 1
. If continuity is not as specified, replace A/C and blower switch.

1991 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1990-92 Manual A/C-Heater Systems
Microsoft
Sunday, July 05, 2009 2:11:52 PMPage 4 © 2005 Mitchell Repair Information Company, LLC.