1991 LEXUS SC300 wiring diagram

OKNG
NGOK
OKNG
INSPECTION PROCEDURE
1Check DOME fuse.
Check for short in all the harness and components con-
nected to the DOME fuse (See attached wiring diagram).
2Check voltage between terminals SYSB and SGND of ECU connector.
C
OK
PRemove ECU with connectors still connected.
Measure voltage between terminals SYSB and SGND
of ECU connector.
Voltage: 10 ± 14 V
Proceed to next circuit inspection shown on matrix chart
(See page BE±276).
3Check continuity between terminal SGND of ECU connector and body ground.\
C
OK
Measure resistance between terminal SGND of ECU
connector and body ground.
Resistance: 1
or less.
Repair or replace harness or connector.
Check and repair harness or connector between
ECU and battery.
±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)BE±287
WhereEverybodyKnowsYourName

WIRING DIAGRAM
Motor Circuit
CIRCUIT DESCRIPTION
The driver's seat ECU controls the 4 motors for slide, front vertical, rear vertica\
l and reclining.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
Inspect the circuit of the motor which is malfunctioning.
Check motor.NG Replace motor.
OK
Check harness and connector between
ECU and motor (See page IN±27). NG
OK Repair or replace harness or
connector.
Proceed to next circuit inspection shown
on matrix chart (See page BE±276).
BE±288
±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

WIRING DIAGRAM
Position Sensor Power Source Circuit
CIRCUIT DESCRIPTION
This circuit provides power to the slide, front vertical, rear vertical and \
reclining sensors.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
Check voltage between terminals PVCC
of ECU connector and body ground.OK
Proceed to next circuit inspection
shown on matrix chart (See page
BE±276
).
NG
NG
OK
Check harness and connector connected to
terminal PVCC of ECU (See page IN±27).Repair or replace harness or
connector.
Check and replace ECU.
BE±292
±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

WIRING DIAGRAM
Position sensor check.OK
Proceed to next circuit inspection
shown on matrix chart (See page
BE±276).
NG
Check position sensor. NG
OK NG
OK Replace position sensor.
Repair or replace harness or
connector.
Check harness and connectors between
ECU and position sensors. (See page
IN±27).
Check and replace ECU.
Position Sensor Circuit
CIRCUIT DESCRIPTION
The position sensor senses movement of the seat and send
pulse signals to the ECU. The position sensor sends pulses
to the ECU in proportion to the amount of seat movement, as
shown in the diagram on the left.
The ECU uses the number of pulses to constantly calculate
the position relative to the memory position and returns the
seat to the memorized position.
If a malfunction occurs in a position sensor and a sensor sig-
nal is not input to the ECU even when the motor operates, the
ECU prohibits return operation.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
BE±294±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

Check stop light operation.NG
OK OK
NG Check stop light circuit
(See page
BE±64).
Proceed to next circuit inspection
shown on matrix chart
(See page
BE±276).
Check voltage between terminals STOP
of ECU connector and body ground.
Check and repair harness and connec-
tor between ECU and stop light switch.
WIRING DIAGRAM
Stop Light Circuit
CIRCUIT DESCRIPTION
The stop light switch sends a brake ON of Off signal to the ECU. When the ECU receives a brake ON signal
it prohibits return of the seat.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
BE±298±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

WIRING DIAGRAM
Check shift position indicator. NGOK
OK
NG Check shift position indicator
circuit (See page BE± 141).
Check voltage between terminal P of ECU
connector and body ground. Proceed to next circuit inspection
shown on matrix chart (See page
BE±276
).
Check and repair harness and connector
between ECU and connector.
Neutral Start Switch Circuit
CIRCUIT DESCRIPTION
The neutral start switch detects when the shift position is in P range and \
sends a signal to the ECU.
When the return switch is turned ON with the IG SW ON and the shift in P\
range, the ECU performs
return operation.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
BE±300±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

WIRING DIAGRAM
Ignition Switch Circuit
CIRCUIT DESCRIPTION
This circuit sends an ignition switch ON or OFF signal to the ECU.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
Check ECU±IG fuse.NG
Check for short in all the harness
and components connected to
ECU±IG fuse.
Check voltage between terminal IG of
ECU connector and body ground. OK
OK
NG Proceed to next circuit inspection
shown on matrix chart
(See page
BE±276).
Check and repair harness or connector
between ECU and battery (See page IN±27).
BE±302±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName

WIRING DIAGRAM
Check voltage between each termi-
nal and a SGND of ECU connector.OK
NG NG
NG
OK
OK
Check power seat switch.
Replace power seat switch.Proceed to next circuit inspection
shown on matrix chart (See page
BE±276).
Check harness and connectors between
ECU and power seat switch (See page
IN±27).Repair or replace harness
or connector.
Check and replace ECU.
Power Seat Switch Circuit
CIRCUIT DESCRIPTION
When the power seat switch is operated, a signal is sent from the power seat\
switch to the ECU and the ECU
sends a signal to the motor to make it operate (except for the lumbar s\
upport).
Even if a malfunction should occur with the position sensor and return opera\
tion is prohibited, manual operation
will occur as normal.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
BE±304±
BODY ELECTRICAL SYSTEM Power Seat Control System (Driver's Seat)
WhereEverybodyKnowsYourName