1991 LEXUS SC300 air intake

Diag. Code 78Fuel Pump Control Circuit
CIRCUIT DESCRIPTION
The fuel pump speed is controlled at two steps (high speed, low speed) by\
the condition of the engine (starting,
light load, heavy load), when the engine starts (STA ON), the engine & ECT ECU sends a Hi signal to the fuel
pump ECU (FPC terminal).
The fuel pump ECU then outputs Hi voltage (battery voltage) to the fuel p\
ump so that the fuel pump operates
at high speed.
After the engine starts, during idling or light loads, the engine & ECT ECU o\
utputs a High Low signal to the fuel
pump ECU, the fuel pump ECU outputs Lo battery voltage (about 9V) to the f\
uel pump and causes the fuel pump
to operate at low speed.
If the intake air volume increases (high engine load), the engine & ECT \
ECU sends a Hi signal to the fuel pump
ECU and causes the fuel pump to operate at high speed.
Code No.Diagnostic Code Detecting ConditionTrouble Area
(1) Open or short in fuel pump circuit for 1 sec. or more with engine speed 1,000 rpm or less.
(2 trip detection logic)*

Open or short in fuel pump ECU circuit.
78
(2) Open in input circuit of fuel pump ECU(FPC) with
engine speed 1,000 rpm or less.
(2 trip detection logic)*
Fuel pump ECU

Engine & ECT ECU power source circuit.

Fuel pump
(3) Open or short in diagnostic signal line (DI) of fuel
pump ECU with engine speed 1,000 rpm or less.
(2 trip detection logic)*

Fuel um

Engine & ECT ECU
*: See page TR±21.
WIRING DIAGRAM
TR±114±
ENGINE TROUBLESHOOTING Circuit Inspection
WhereEverybodyKnowsYourName

234
AUTOMATIC AIR CONDITIONER
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EB134ENGINE WIRE AND ENGINE ROOM MAIN WIRE (FRONT SIDE OF R/B NO. 2)
IE136ENGINE ROOM MAIN WIRE AND COWL WIRE (R/B NO. 4)
IE236ENGINE ROOM MAIN WIRE AND COWL WIRE (BEHIND GLOVE BOX)
IG136INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO. 5)
II136ENGINE WIRE AND A/C WIRE (BEHIND GLOVE BOX)
IJ236ENGINE WIRE AND COWL WIRE (RIGHT KICK PANEL)
IK136ENGINE WIRE AND INSTRUMENT PANEL WIRE (RIGHT KICK PANEL)
IN138ENGINE ROOM MAIN WIRE AND A/C WIRE (BEHIND GLOVE BOX)
IQ138INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)
IR138CONSOLE BOX WIRE AND A/C SUB WIRE (BEHIND GLOVE BOX)IR238CONSOLE BOX WIRE AND A/C SUB WIRE (BEHIND GLOVE BOX)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA34FRONT SIDE OF RIGHT FENDER
EB34FRONT SIDE OF LEFT FENDER
ED34REAR SIDE OF INTAKE MANIFOLD
IF36LEFT KICK PANEL
IJ36RIGHT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E1134ENGINE ROOM MAIN WIREI2838CONSOLE BOX WIREE1834ENGINE WIREI2938CONSOLE BOX WIRE
I2738A/C WIREI3238ENGINE WIRE
WhereEverybodyKnowsYourName

66
.
ENGINE CONTROL
THIS SYSTEM UTILIZES AN ECU AND MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE O\
F
THE ENGINE CONTROL IS EXPLAINED HERE.
1. INPUT SIGNALS
(1) WATER TEMP. SIGNAL CIRCUITTHE WATER TEMP. SENSOR DETECTS THE ENGINE COOLANT TEMP. AND HAS A BUILT±IN THERMISTOR WITH A RESISTANCE
WHICH VARIES ACCORDING TO THE WATER TEMP. THE WATER TEMP. IS INPUT INTO TERMINAL THW OF ENGINE CONTROL
ECU AS A CONTROL SIGNAL.
(2) INTAKE AIR TEMP. SIGNAL CIRCUIT THE INTAKE AIR TEMP. SENSOR IS INSTALLED IN THE AIR FLOW METER AND DETECTS THE INTAKE AIR TEMP., WHICH IS INPUT
AS A CONTROL SIGNAL TO TERMINAL THA OF ENGINE CONTROL ECU.
(3) OXYGEN SENSOR SIGNAL CIRCUIT THE OXYGEN DENSITY IN THE EXHAUST EMISSION IS DETECTED AND INPUT AS A CONTR\
OL SIGNAL FROM THE OXYGEN
SENSOR NO. 1 AND NO. 2 TO TERMINALS OX1, OX2 OF THE ECU AND FROM THE OXYGEN SENSOR SUB (FOR CALIFORNIA) TO
TERMINAL OX3 OF THE ECU.
TO STABILIZE DETECTION PERFORMANCE BY THE OXYGEN SENSOR SUB (FOR CALIFORNIA)\
IS WARMED. THIS HEATER IS
ALSO CONTROLLED BY THE ECU (HT).
(4) RPM SIGNAL CIRCUIT CRANKSHAFT POSITION IS DETECTED BY THE PICK±UP COIL INSTALLED INSIDE THE DISTRIBUTOR. CRANKSHAFT POSITION
IS INPUT AS A CONTROL SIGNAL TO TERMINALS G1 AND G2 OF THE ECU, AND RPM IS INPUT TO TERMINAL NE.
(5) THROTTLE SIGNAL CIRCUIT THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE AS A CONTROL SIGNAL, WHICH IS
INPUT INTO TERMINAL VTA1 OF THE ECU. WHEN THE VALVE IS COMPLETELY CLOSED, THE CONTROL SIGNAL IS INPUT INTO
TERMINAL IDL1 .
(6) VEHICLE SPEED CIRCUIT THE VEHICLE SPEED IS DETECTED BY SPEED SENSOR NO. 1 INSTALLED IN THE TRANSMISSION AND THE SIGNAL IS INPUT TO
TERMINAL SPD OF THE ECU VIA THE COMB. METER.
(7) NEUTRAL START SIGNAL CIRCUIT THE NEUTRAL START SW DETECTS WHETHER THE SHIFT POSITION IS IN NEUTRAL OR NOT, AND THE SIGNAL IS INPUT INTO
TERMINAL NSW OF THE ECU.
(8) AIRCONDITIONING SW SIGNAL CIRCUIT THE OPERATING VOLTAGE OF THE A/C MAGNETIC CLUTCH IS DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL ACMG OF
ECU AS A CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ECU. WITH THE IGNITION SW TURNED ON, THE VOLTAGE FOR
ECU START±UP POWER SUPPLY IS APPLIED TO TERMINALS +B AND +B1 OF ECU VIA EFI MAIN RELAY.
THE CURRENT FLOWING THROUGH THE IGN FUSE FLOWS TO TERMINAL IGSW OF THE ECU.
(10) INTAKE AIR VOLUME SIGNAL CIRCUIT INTAKE AIR VOLUME IS DETECTED BY THE AIR FLOW METER AND THE SIGNAL IS INPUT TO TERMINAL KS OF THE ECU AS A
CONTROL SIGNAL.
(11) STOP LIGHT SW SIGNAL CIRCUIT THE STOP LIGHT SW IS USED TO DETECT WHETHER OR NOT THE VEHICLE IS BRAKING AND THE SIGNAL IS INPUT INTO
TERMINAL STP OF THE ECU AS A CONTROL SIGNAL.
(12) STA SIGNAL CIRCUIT TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ECU AS A CONTROL SIGNAL.
(13) ENGINE KNOCK SIGNAL CIRCUIT ENGINE KNOCKING IS DETECTED BY KNOCK SENSOR NO. 1 AND NO. 2 AND THE SIGN\
AL IS INPUT INTO TERMINALS KNK1 AND
KNK2 AS A CONTROL SIGNAL.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName

67
2. CONTROL SYSTEM
*EFI (ELECTRONIC FUEL INJECTION) SYSTEM
THE EFI SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT FROM EACH SENSOR (IN\
PUT SIGNALS
FROM (1) TO (13) ETC.) TO THE ECU. THE BEST FUEL INJECTION TIMING IS DECIDED BASED ON THIS DATA AND THE PROGRAM
MEMORIZED BY THE ECU, AND THE CONTROL SIGNAL IS OUTPUT TO TERMINALS #10, #20, #30, #40, #50 AND #60 OF THE ECU TO
OPERATE THE INJECTOR. (INJECT THE FUEL). THE EFI SYSTEM PRODUCES CONTROL OF FUEL INJECTION OPERATION BY THE
ECU IN RESPONSE TO THE DRIVING CONDITIONS.
* ESA (ELECTRONIC SPARK ADVANCE) SYSTEM
THE ESA SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT TO THE ECU FROM EACH SENSOR (INPUT
SIGNALS FROM (1), (2), (4) TO (13) ETC.). THE BEST IGNITION TIMING IS DECIDED ACCORDING TO THIS DATA AND THE
MEMORIZED DATA IN THE ECU AND THE CONTROL SIGNAL IS OUTPUT TO TERMINAL IGT THIS SIGNAL CONTROLS THE IGNITER
TO PROVIDE THE BEST IGNITION TIMING FOR THE DRIVING CONDITIONS.
* OXYGEN SENSOR HEATER CONTROL SYSTEM (USA SPEC.)
THE OXYGEN SENSOR HEATER CONTROL SYSTEM TURNS THE HEATER ON WHEN THE INTAKE AIR VOLUME IS LOW (TEMP. OF
EXHAUST EMISSIONS IS LOW), AND WARMS UP THE OXYGEN SENSOR TO IMPROVE DETECTION PERFORMANCE OF THE
SENSOR.
THE ECU EVALUATES THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (2), (4)\
, (9) TO (11) ETC.,) AND OUTPUTS
CURRENT TO TERMINAL HT TO CONTROL THE HEATER.
* ISC (IDLE SPEED CONTROL) SYSTEM
THE ISC SYSTEM (STEP MOTOR TYPE) INCREASES THE RPM AND PROVIDES IDLING STABILITY FOR FAST IDLE±UP WHEN THE
ENGINE IS COLD, AND WHEN THE IDLE SPEED HAS DROPPED DUE TO ELECTRICAL LOAD AND SO ON. THE ECU EVALUATES
THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (5), (8)\
, (9), (11) ETC.), OUTPUTS CURRENT TO TERMINAL ISC1,
ISC2, ISC3 AND ISC4 TO CONTROL ISC VALVE.
* EGR CONTROL SYSTEM
THE EGR CONTROL SYSTEM DETECTS THE SIGNAL FROM EACH SENSOR (INPUT SIGNALS \
FROM (1), (4), (9), (10) ETC.), AND
OUTPUTS CURRENT TO TERMINAL EGR TO CONTROL THE EGR VALVE.
* FUEL PUMP CONTROL SYSTEM
THE COMPUTER OUTPUTS CURRENT TO TERMINAL FPC AND CONTROLS THE FUEL PUMP ECU AND FUEL PUMP DRIVE SPEED
IN RESPONSE TO CONDITIONS.
* ACIS (ACOUSTIC CONTROL INDUCTION SYSTEM)
ACIS INCLUDES A VALVE IN THE BULKHEAD SEPARATING THE SURGE TANK INTO TWO PARTS. THIS VALE IS OPENED AND
CLOSED IN ACCORDANCE WITH THE DRIVING CONDITIONS TO CONTROL THE INTAKE MANIFOLD LENGTH IN TWO STAGES FOR
INCREASED ENGINE OUTPUT IN ALL RANGES FROM LOW TO HIGH SPEEDS.
THE ECU JUDGES THE VEHICLE SPEED BY THE SIGNALS ((4), (5)) FROM EACH \
SENSOR AND OUTPUTS SIGNALS TO THE
TERMINAL ACIS TO CONTROL THE VSV (FOR OPENING AND CLOSING THE INTAKE CONTROL VALVE).
3. DIAGNOSIS SYSTEM
WITH THE DIAGNOSIS SYSTEM, WHEN THERE IS A MALFUNCTION IN THE ECU SIGNAL\
SYSTEM, THE MALFUNCTIONING SYSTEM IS
RECORDED IN THE MEMORY. THE MALFUNCTIONING SYSTEM CAN BE FOUND BY READING THE CODE DISPLAYED BY THE
CHECKING ENGINE WARNING LIGHT.
4. FAIL±SAFE SYSTEM
WHEN A MALFUNCTION HAS OCCURRED IN ANY SYSTEM, IF THERE IS A POSSIBILITY OF \
ENGINE TROUBLE BEING CAUSED BY
CONTINUED CONTROL BASED ON THE SIGNALS FROM THAT SYSTEM, THE FAIL±SAFE SYSTEM EITHER CONTROLS THE SYSTEM
BY USING DATA (STANDARD VALUES) RECORDED IN THE ECU MEMORY OR ELSE STOPS THE ENGINE.
NOTE: THE SPECIFICATION DESCRIPTIONS ªUSA SPEC.º AND ªEXC. USA SPEC.º USED IN THIS SECTION INDICATE THE
FOLLOWING SPECIFICATIONS.
USA SPEC. : USA (50 STATES) SPECIFICATIONS
EXC. USA SPEC. : USA (EXCEPT CALIFORNIA) AND CANADIAN SPECIFICATIONS.
WhereEverybodyKnowsYourName

74
ENGINE CONTROL
EFI MAIN RELAY2 ± 4: CLOSED WITH IGNITION SW AT ON OR ST POSITION
W 4 WATER TEMP. SENSOR
1 ± 2: APPROX. 16.2K (±20 °C, ±4°F)
: APPROX. 2.45K (20 °C, 68°F)
: APPROX. 0.32K (80 °C, 176 °F)
E 3 EGR GAS TEMP. SENSOR (FOR USA SPEC.)
1 ± 2: APPROX. 78.30K (50 °C, 122 °F)
APPROX. 13.06K (100 °C, 212 °F)
APPROX. 3.16K (150 °C, 302 °F)
E 9(A), E10(B) ENGINE AND ECT ECU, E11(A), E12(B) ENGINE ECU
(VOLTAGE AT ENGINE AND ECT ECU WIRING CONNECTORS)
BATT ± E1 : ALWAYS APPROX. 12 VOLTS
IGSW ± E1 : APPROX. 12 VOLTS WITH IGNITION SW ON
+B, +B1 ± E1 : APPROX. 12 VOLTS WITH IGNITION SW ON
VC ± E2 : 4±6 VOLTS WITH IGNITION SW ON
IDL1, IDL2 ± E2 : 0±1 VOLTS WITH IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED
: 10±14 VOLTS WITH IGNITION SW ON AND THROTTLE VALVE FULLY OPEN
VTA1, VTA2 ± E2 : 0.1±1.0 VOLTS WITH IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED
: 3±6 VOLTS WITH IGNITION SW ON AND THROTTLE VALVE FULLY OPEN
THA ± E2 : 1±3 VOLTS WITH IGNITION SW ON AND INTAKE AIR TEMP. 20°C ( 68°F)
THW ± E2 : 0.1±1.0 VOLTS WITH IGNITION SW ON AND COOLANT TEMP. 80°C ( 176 °F)
STA ± E1 : 6±14 VOLTS WITH ENGINE CRANKING
#10, #20, #30, #40, #50, #60 ± E1 : APPROX. 12 VOLTS WITH IGNITION SW ON
IGF ± E1 : 0±1 VOLTS WITH ENGINE IDLING
MREL ± E1 : APPROX. 12 VOLTS WITH IGNITION SW ON
DI ± E1 : 7.5±14 VOLTS WITH ENGINE IDLING
ISC1, ISC2, ISC3, ISC4 ± E1 : APPROX. 12 VOLTS WITH IGNITION SW ON
HTL1, HTR1, HTL2, HTR2 ± E01 : 0±2 VOLTS WITH ENGINE IDLING
EGR ± E1 : APPROX. 12 VOLTS WITH ENGINE IDLING
NSW ± E1 : 0±1 VOLTS WITH IGNITION SW ON AND SHIFT LEVER P OR N RANGE
: 10±14 VOLTS WITH IGNITION SW ON AND SHIFT EXCEPT P OR N RANGE
TE1 ± E1 : APPROX. 12 VOLTS WITH IGNITION SW ON
TE2 ± E2 : APPROX. 12 VOLTS WITH IGNITION SW ON
W ± E1 : APPROX. 12 VOLTS WITH ENGINE IDLING
0±2 VOLTS WITH IGNITION SW ON
A/C ± E1 : 0±2 VOLTS WITH AIR CONDITIONER ON
10±14 VOLTS WITH AIR CONDITIONER OFF
ACMG ± E1 : 0±2 VOLTS WITH AIR CONDITIONER ON
: 10±14 VOLTS WITH AIR CONDITIONER OFF
TR ± E1 : APPROX. 12 VOLTS WITH IGNITION SW ON
VTA1, VTA2 ± E2 : 0±1 VOLTS WITH IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED
3±5.5 VOLTS WITH IGNITION SW ON AND THROTTLE VALVE FULLY OPEN
NE ± E1 : 4±6 VOLTS WITH IGNITION SW ON
(RESISTANCE OF ENGINE AND ECT ECU WIRING CONNECTORS)
+B, +B1 ± #10, #20, #30, #40, #50, #60 : 13.2±14.2
+B, +B1, ISC1, ISC2, ISC3, ISC4 : 10±30
+B, +B1 ±EGR: 33±39
+B, +B1, HT : 5.1±6.3
+B, +B1 ±EVAP : 30±34
IDL1, IDL2 E2 : INFINITY WITH THROTTLE VALVE OPEN 0±0.5WITH THROTTLE VALVE FULLY CLOSED
VTA1, VTA2 E2 : 2.4±10.7WITH THROTTLE VALVE FULLY OPEN
0.3±5.9 WITH THROTTLE VALVE FULLY CLOSED
VCC ± E2 : 3±7K
THW ± E2 : 200±400 WITH COOLANT TEMP. 80°C ( 176 °F)
THA ± E2 : 2±3K WITH INTAKE AIR TEMP. 20°C ( 68°F)
THG ± E2 : 69.4±88.5K WITH EGR GAS TEMP. 50°C ( 11 2 °F)
G1, G2 ±G± : 0.835±13.5K
NE± G± : 0.835±13.5K
SERVICE HINTS
WhereEverybodyKnowsYourName

567 8
EB1
EC ED D DCCCCD
CCCC
C IJ2 IJ2
IG2
EB1
C D C DC C CCC
DDCDDDDDCCCCC
ED
1 2
1
2 23
1 23
14
4 234 51
25
1346
2
B±O
B±W B±OB±Y
B± R
B± R
W
R± LBR
B± R B±Y W
L±R
B±Y LG
GR±Y B Y B
G±W L±Y
R± G P B± R
B± R
18 19 17 16 15 46 23 44 34
31 32 34 32 35 33 33 24 2 76 1 37B
B± Y
B±R W
L±R
W± B
W± B
BR
LG±BL±WV±R
G± YB± Y
B± O P
B±W B± O
BR
W
L±R
B±R
P
B±O
BR
BR
#30 #20 #40 #50 #60 THG ACMG THW A/C
B±R
B±R
B±R
EB1
Fro m
Spe ed Sen sor
< 21±7>
P± L
Y± L
V± Y
Y± G
W± Y Y±R
L±R
Y± B
Y± G L±R
L±R
BR
BR
65 63 42 64 43 38 39 40 58 57 41 45 66 A9
AIR FLOW METER
From Trac tion ECU
< 8±8>
From I gniter
< 1±6>
7P
E2 IDL2 VTA2
IDL1
VTA1
THA
VC KS
IGT
IGF
VT 01
VT 02
NEO
TR
IGSW
NS W
SP1
M±REL
BATT
ISC3
ISC1
ISC4
ISC2
+B1
+B I1
ISC
VALVEBR
R±BBR
Y± L
L±R
R
Y
L±R
L±R
L±R
BR
L±R
BR
BR
BR
BR
BR W
G
From Magnet ic
Cl ut ch Rel ay
< 22±1>
To A/ C Amp lif ie r
< 22±7>
E3
EGR GAS TEMP. SENSOR
E2
EFI WATER TEMP. SENSOR
S9
SUB THROTTL E
POSITI ON SENSOR T2
THROTTLE
POSITI ON SENSOR
BR
Engine Control
2LEXUSSC300
(
Cont ' d )
ENGI NE AND ECT ECU, ENGI NE ECU *
1: (
w/ Trac tion Control )
(
* 1)
( * 2)
( * 1)
( * 2)
(
* 1 ) *
2:
(
w/ o Tr a ct i o n Co nt r ol )
(
* 1 ) To Trac ti on
ECU< 8±8>
R±B
R
4311 8
B±O
BR (
* 3)
(
* 3) *
3: (
US A S pe c. )
* 4:
(
Ex . USA Spe c. )
E9 , E10 DC
BR
Front side of
intake manifold Rear side of
c ylinder head RH Rear side of
c ylinder head RH
C
C
C 1 2
1
2
2
1
C
C
C
C
C
C
D
D
C
C
C
C
D
D
C
D
C
D
D
20
77
27
7
25
26
22
21
80
79
4
69
4
6
29
20
28
19
17
V7
VSV (
for Int ake
Contr ol Valve )
V2
VSV
(
for EVAP )
V1
VSV
(
for EGR )
BY1
BY1
BY1 BY1
BR
R±B
(
* 4 )
W
(
* 4 )
B±R
BR±W
(
* 3 )
R±L
(
* 3
)
3142 1256
IK2
IK2
12
22
C
C
1
O3
OXYGEN SENSOR
MAIN No. 1
(
ON Front Side )
C48 71 61 75 74
1
O4
OXYGEN SENSOR
MAIN No. 2
(
ON Rear Side )
C
D
1 2
35 47
P2 0
POWER STEERING
PRESSURE SW
IK11
IJ1
IJ1
(SHIELDED )2341 C
C
1
1 49
50
D1 3
DI ST RI B UTOR
( SHIELDED )
EC
Front side of
intake manifold
G±Y G± R
8
14
K1
No. 1(
ON Fr ont Side )
KNOCK SENSOR
K2
No. 2 (
ON Rear Side ) BR BR
BR
W
W L
B Y
R R±G
P
W± B
W± B G±W
L±Y
GR±Y LG
B±Y
G±Y
BR
BR
BR
G1 G2 G± NE
#10
TT TE2 VF2 TE1 VF1 W STP E1 E1 1 E0 2 E01 DI FPC G1 G2 G± NE KNK1 KNK2 STA ACI S
PS OX2 OX1 HT OX3 EGR EVAP 39
G± R G±B
B±W BR± W
BR± W
BR
B±R
B±R
B±R
B±R
W
BR± W
W
R±L
BR BR
BR
R±L W
LG±B BR
BR
(
SHI ELDED )
(
SHI EL DED )
(
SHI ELDED )
( SHIELDED )
O8
OXYGEN SENSOR SUB
(
for California )
BR
BR
Y B
R± L
BR
(* 4)
(
* 4)
(A/ T )
WhereEverybodyKnowsYourName

181
THE SRS (SUPPLEMENTAL RESTRAINT SYSTEM) AIRBAG IS A DRIVER PROTECTION DEVICE WHICH HAS A SUPPLEMENTAL ROLE
TO THE SEAT BELTS.
CURRENT FLOWS CONSTANTLY TO TERMINAL 6 OF THE CENTER AIRBAG SENSOR ASSEMBLY. WHEN THE IGNITION SW IS
TURNED TO ACC OR ON, CURRENT FROM THE CIG FUSE FLOWS TO TERMINAL 14 OF THE CENTER AIRBAG SENSOR ASSEMBLY.
ONLY WHEN THE IGNITION SW IS ON DOES THE CURRENT FROM THE IGN FUSE TO TERMINAL 7 .
IF AN ACCIDENT OCCURS WHILE DRIVING, DECELERATION CAUSED BY A FRONTAL IMPACT IS DETECTED BY EACH SENSOR AND
SWITCH, AND WHEN THE FRONTAL IMPACT EXCEEDS A SET LEVEL (WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG
SENSOR ASSEMBLY IS ON AND THE CENTER AIRBAG SENSOR IS ON, FRONT AIRBAG SENSORS ARE OFF), CURRENT \
FROM THE
CIG OR IGN FUSE FLOWS TO TERMINAL 11 OF THE CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG SQUIB "
SQUIB " TERMINAL 2 " TERMINAL 10 OF CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 8, TERMINAL 13 OR BODY GROUND
" GROUND.
WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON AND THE FRONT AIRBAG SENSOR LH OR
RH IS ON, CENTER AIRBAG SENSOR IS OFF AND CURRENT FROM THE CIG OR IGN FUSE FLOWS TO TERMINAL 11 OF THE CENTER
AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG SQUIB " SQUIB " TERMINAL 2 " TERMINAL 10 OF CENTER AIRBAG
SENSOR ASSEMBLY " TERMINAL 3 OR 4 " TERMINAL 1 OF FRONT AIRBAG SENSOR " TERMINAL 2 " TERMINAL 2 OR 5 OF
CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 8, TERMINAL 13 OR BODY GROUND " GROUND , WHEN THE SAFING SENSOR
BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON, AND THE FRONT AIRBAG SENSOR LH OR RH IS ON AND CENTER
AIRBAG SENSOR IS ON ONE OF THE ABOVE±MENTIONED CIRCUITS IS ACTIVATED SO THAT CURRENT FLOWS TO THE AIRBAG
SQUIB AND CAUSES IT TO OPERATE. THE BAG STORED INSIDE THE STEERING WHEEL PAD IS INSTANTANEOUSLY EXPANDED TO
SOFTEN THE SHOCK TO THE DRIVER.
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A2928C1228T 629
C 326F 126
C1028F 226
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1E20INSTRUMENT PANEL WIRE
1G20COWL NO. 2 WIRE
1J20COWL WIRE
3A
3B
3D22INSTRUMENT PANEL WIRE
3E
3H
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IK136ENGINE WIRE AND INSTRUMENT PANEL WIRE (RIGHT KICK PANEL)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC34FRONT SIDE OF INTAKE MANIFOLD
ED34REAR SIDE OF CYLINDER HEAD RH
IF36LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E2034ENGINE WIRE
SYSTEM OUTLINE
WhereEverybodyKnowsYourName