1991 FORD SIERRA key

31Attach a suitable hoist to the engine lifting
brackets located at the front and rear of the
cylinder head, and carefully take the weight of
the engine. The engine should be supported
horizontally, ie do not allow it to tilt front to rear.
32Raise the engine until the engine
mountings are clear of the crossmember then
pull the engine forwards to disconnect it from
the gearbox. Ensure that the gearbox is
adequately supported, and take care not to
strain the gearbox input shaft. It may be
necessary to rock the engine a little to release
it from the gearbox.
33Once clear of the gearbox, lift the engine
from the vehicle, taking care not to damage
the radiator fins.
Note: Refer to the warning in Section 8 before
proceeding. A suitable hoist and lifting tackle
will be required for this operation.
1Proceed as described in Section 9,
paragraphs 1 to 17 inclusive, but additionally,
where applicable, disconnect the kickdown
cable from the carburettor/inlet manifold.
2Unscrew and remove the top engine-to-
transmission bolts which are accessible from
the engine compartment. Note the location of
the earth strap, vacuum pipe bracket, and
transmission dipstick tube bracket.
3Proceed as described in Section 9,
paragraphs 20 to 24 inclusive.
4Working through the starter motor aperture,
unscrew the four torque converter-to-
driveplate nuts. It will be necessary to turn the
crankshaft, using a suitable spanner on the
crankshaft pulley bolt, in order to gain access
to each nut in turn through the aperture.
5Unscrew and remove the remaining engine-
to-transmission bolts, and remove the bolt
from the engine adapter plate. Where
applicable pull the blanking plug from the
adapter plate.
6Remove the two securing bolts and
disconnect the engine-to-transmission brace
from the engine and transmission.
7Lower the vehicle to the ground, and
support the transmission with a trolley jack,
using a block of wood between the jack and
the transmission to spread the load.
8Proceed as described in Section 9,
paragraphs 30 and 31.
9Raise the engine until the engine mountings
are clear of the crossmember, then pull the
engine forwards to disconnect it from the
transmission. Ensure that the torque converter
is held firmly in place in the transmission
housing, otherwise it could fall out resulting in
fluid spillage and possible damage. It may be
necessary to rock the engine a little to release
it from the transmission.
10Once clear of the transmission lift the
engine from the vehicle, taking care not to
damage the radiator fins.Note: Refer to the warning in Section 8 before
proceeding. A suitable hoist and lifting tackle
will be required for this operation.
Removal
1Proceed as described in Section 9,
paragraphs 1 to 17 inclusive.
2Note the location of the earth strap on the
rear inlet manifold stud, then remove the nut
and disconnect the strap.
3Working inside the vehicle, unscrew the
gear lever knob and remove the centre
console. Where a full length console is fitted,
it is only necessary to remove the front tray.
4Detach the outer gaiter from the retaining
frame and withdraw it over the gear lever.
5Unscrew the securing screws on early
models, or release the clips on later models,
and remove the gaiter retaining frame and
inner gaiter.
6Using a suitable Torx key, remove the
screws securing the gear lever to the gearbox
extension housing, and withdraw the gear
lever. Note how the base of the gear lever
locates over the selector shaft.
7Jack up the vehicle and support on axle
stands (see ÒJacking and Vehicle SupportÓ).
Ensure that there is sufficient working room
beneath the vehicle.
8To improve access, disconnect the exhaust
downpipe from the manifold and remove the
exhaust system.
9Remove the propeller shaft.
10Where applicable bend back the locktabs,
then unscrew the two bolts in each case
securing the two anti-roll bar U-clamps to the
vehicle underbody. Lower the anti-roll bar as
far as possible.
11Proceed as described in Section 9,
paragraphs 27 and 28.
12Drain the engine oil into a container.
13Unscrew the nuts or bolts, as applicable,
securing the engine mountings to the
crossmember. Recover the washers.
14Disconnect the wiring from the reversing
lamp switch.
15Remove the retaining circlip, and
withdraw the speedometer cable from the
gearbox extension housing.
16Support the gearbox with a trolley jack,
using a block of wood between the jack and
the gearbox to spread the load.
17Unscrew the four bolts securing the
gearbox crossmember to the vehicle
underbody. Unscrew the central bolt securing
the crossmember to the gearbox and remove
the crossmember. Note the position of the
earth strap, where applicable. Recover the
mounting cup and where applicable the
exhaust mounting bracket and heat shield.
18Make a final check to ensure that all
relevant wires, pipes and hoses have been
disconnected to facilitate removal of the en-
gine/gearbox assembly.19Attach a suitable hoist to the engine lifting
brackets located at the front and rear of the
cylinder head. Arrange the lifting tackle so that
the engine/gearbox assembly will assume a
steep angle of approximately 40¼ to 45¼ as it is
being removed.
20Raise the engine/gearbox so that the
engine mountings are clear of the
crossmember, then ease the assembly
forwards, at the same time lowering the trolley
jack which is supporting the gearbox. Lift the
assembly from the vehicle, taking care not to
damage surrounding components (see
illustration).
21With the engine/gearbox assembly
removed, temporarily reconnect the anti-roll bar
to the underbody if the vehicle is to be moved.
Separation
22To separate the engine from the gearbox,
proceed as follows.
23Remove the starter motor.
24Support the engine and gearbox
horizontally on blocks of wood.
25Unscrew the two securing bolts and
disconnect the engine-to-gearbox brace from
the engine and gearbox.
26Unscrew and remove the engine-to-
gearbox bolts, noting the location of the earth
strap, and remove the bolt from the engine
adapter plate.
27Pull the engine and gearbox apart, taking
care not to strain the gearbox input shaft. It
may be necessary to rock the units slightly to
separate them.
Note: Refer to the warning in Section 8 before
proceeding. A suitable hoist and lifting tackle
will be required for this operation. Any
suspected faults in the automatic transmission
should be referred to a Ford dealer or
automatic transmission specialist before
removal of the unit, as the specialist fault
diagnosis equipment is designed to operate
with the transmission in the vehicle.
Removal
1Proceed as described in Section 9,
paragraphs 1 to 17 inclusive, but additionally,
12Engine/automatic
transmission assembly -
removal and separation
11Engine/manual gearbox
assembly - removal and
separation
10Engine - removal leaving
automatic transmission in
vehicle
SOHC engines 2A¥9
2A
11.20 Lifting the engine/gearbox assembly
from the vehicle