1990 MITSUBISHI ECLIPSE ignition

23-40BODY - Seat Belts
Door latch
switch
Ignition
switch
(LOCK or
ZjTI
Warninglight
.
F-w4Approx. 6 sec.
~1: Warning alarm when ignition
switch is activated.
r2: Approx. 0.7 sec./cycle
Driver’s side
latch switch
Ignition
switch
(LOCK or
Er:rI
ti Fasten” switch
Driver’s side
(ON) i;outer switch
(OFF)I!
’ III
Buzzer(ON’
(OFF)c
Warning ’light
kprox. 66 sec.’Ignition
switch
(LOCK or zm
zs;;;$s (ON)
side outer
switch(OFFIr
Warninglight
Apprbx.ti sec.Warning Alarm when the Automatic Seat Belt is
no*Completely Fastened (when the slide anchor, during
movement, stops before completion of travel, or when it
moves toward the “fasten” side)
The warning light flashes if the door is closed, the ignition
switch is at “ON” position and the driver’s or front passenger’sseat “fasten” switch is switched ON (unfastened status).
Warning Alarm when the Driver’s Shoulder Belt is not
FastenedWhen, with the driver’s door closed, the ignition switch ON ant
the slide anchor at the “fasten” position (the “fasten” switch is
OFF), the shoulder belt is not fastened (the outer switch is
switched OFF), the buzzer will sound continuously for approx-
imately 6 seconds and, at the same time, the warning light will
‘flash for approximately 68 seconds.
If, however the shoulder belt is fastened (the outer switch is
switched ON) during that period, the warning light and buzzer
will be switched OFF.Warning Alarm when the Front Seat Passenger’s Shoulder
.Belt .is not Fastened
When, with the front seat passenger’s shoulder belt unfas-tened (the outer switch is switched OFF), the ignition switch
i--turned from the “LOCK” or “ACC” position to the “ON
position, the warning light will illuminate steadily for
approx-imately 68 seconds. If, however, the shoulder belt is fastened
(the outer switch is switched ON) during that period, thewarning light will be switched OFF.
I

BODY- Seat Belts*23-41
switchDriver’s
side buckle
switch
Buzzer(ON’ XL(OFF)
,: Approx. 0.7 sec./cycle
Key-reminder (ON)switch (A) (OFF)
Buzzer
19Poo270
Automatic seat belt control unit
connector terminals
lsPo2eeWarning Alarm when the Driver’s Lap Belt is not Fastened
When, with the driver’s lap belt unfastened (the buckle switchis switched ON), the ignition switch is tunrned from the
“LOCK” or
“ACC” position to the “ON” position, the buzzer
will sound intermittently for approximately 6 seconds. If,however, the driver’s lap belt is fastened during that time, the
buzzer will be switched
OFF.
Note that the warning light when the ignition switch isactivated will also illuminate when the ignition switch is turned
from the “LOCK” or “ACC” position to the “ON” position.
Warning Alarm when the ignition Key is Left in the Ignition
The buzzer will sound continuously when all of these condi-
tions occur simultaneously: the key is in the key cylinder
(key-reminder switch A is switched ON), and the ignition
switch is at the “LOCK” or “ACC” position, and the driver’s
door is open (the door latch switch “open” is switched ON).
Warning Alarm when an Automatic Seat Belt Starts to
Move toward the “Release” Side
When the driver’s or front seat passenger’s automatic seat belt
starts to move toward the “release” side, the buzzer sounds
for approximately 0.7 second.AUTOMATlC SEAT BELT CONTROL UNIT INPUT/OUTPUT
SIGNALS
Power Supply and Ground Circuit
INameITerminal No.IVoltage levelI
I Battery (+B)I11I H 1
I Ignition switchI ’ IH or LI
IGroundI7, 17Io.ovI
NOTEH and L in the voltage level column indicate the terminal voltage Of
each signal.H: Battery voltageL:Ground voltage (0.8V or less)

23-42BODY - Seat Belts
Input Signals
The relationship between input signals (as seen
from the control unit) and the ON/OFF status of the
various switches is as shown in the table below.
When making measurements of voltage, be sure todo so within one minute from the time that
theignition switch is turned to the “ON”, “LOCK” or
“ACC” position.
Input signaldesignation
Ignition switch
Driver’s seat
buckle switch
Driver’s seat outer
3switchAmount of shoulder belt wind-in equals or exceeds theOFFHspecified amount.
Driver’s seat
“fasten” switch
Driver’s seat
“release” switch
Driver’s seat door
latch switch
(“open” side)
Key-reminderswitch
(A)
Key-reminderswitch (B)Front passenger’s
outer switch
cFront passenger’s
“fasten” switch
Front passenger’s
a release m switch
Terminal
No.Switch operation and statusVcv;y
1Ignition switch is switched to “ON”.ONHIgnition switch is switched to “LOCK” or “ACC”.
OFFL
2
Lap belt is fastened.OFFH
Lap belt is not fastened.ION I ilAmount of shoulder belt wind-in is between 0 and the
specified amount.
ONL
4Driver’s door is opened, or belt is fastened.OFFH
Driver’s door is closed, and belt is not fastened.
ONL
5Driver’s belt is in the released condition.
OFFHDriver’s belt is in the unreleased condition.
ONL Y
6
12
13
14
15Driver’s door is closed.
Driver’s door is open.
+
Key is in key cylinder.
Key is removed from the key cylinder.Key is removed from the key cylinder.
Key is in key cylinder.Amount of shoulder belt wind-in equals or exceeds the
specified amount.
Amount of shoulder belt wind-in is between 0 and the
specified amount.
Front passenger’s door is opened, or belt is fastened.
Front passenger’s door is closed, and belt is notfastened.
OFFH I
ONL
ONH
OFFL
ONH
OFFL
OFFH
ONL
OFFH
ONL
16Front passenger’s door is closed, or belt is in the releasedOFFHcondition.
Front passenger’s door is open, and the belt is in theunreleased condition.ONL
,

BODY - Seat Belts23-43
9utput SignalsJhen the input signals change, the signals output
rorn the control unit also change. This relationsihp
; as shown in the table below.
IUZZER OPERATION (TERMINAL No.201
Warning alarm whendriver’s shoulder belt
is not fastened
Warning alarm whendriver’s lap belt is not
fastened
Warning alarm whenkey is left in key
cylinder
Time expiration
Warning alarm whenshoulder belt starts
moving to “release”
sideStatus at input sideIgnition switch
Driver’s door
Driver’s
shoulder belt(“Fasten” switch)
Driver’souter switch
Other than as aboveDriver‘s
lap beltIgnition switch
Other than as above
ON
Closed
E-Yned
OFFNot fastenedOFF-+ ON
*
Other than as above
hh
Other than as above
Shoulder beit
release
Other than as aboveWhen beginsOutput signal waveforms
1
Buzzer
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFFand operation status
Output signal
(ON)I--i
Approx. 6 sec.

23-44BODY -Seat Belts
WARNING LIGHT OPERATION (TERMINAL No. 10)
Status at input side
VVarning alarm whenlgnition switchOFF 3 ONignition switch is
activated
Other than as above
Warning alarm whenautomatic seat belt
fastening is
incomplete
1 Ignition switch
Driver’s or passenger’s seatION
belt
r;tNfasyed
’(“Fasten” switch, Door latchswitch “close”)
Other than as above
Warninn alarm whenIgnition switch1 ONdriver’sshoulder belt -
is not fastenedDriver’s door
Driver’s shoulder belt
(“Fasten” switch)
Closed
Fastened
(OFF)Driver’s outer switch
Other than as above
OFF
Warning alarm whenfront passenger’s
shoulder belt is not
fastenedPassenger’s outer switch
lgnition
swtich
Other than as above
OFF
OFF+ ON
r
Light
ON
OFF
ON
OFF
ON
OFF
ON
OFF
DRIVER’S SHOULDER BELT FASTENING OPERATION (TERMINAL No.8)Status at input side
Driver’s shoulder belt
is fastened.
‘~
Other than as aboveOutput signal waveforms
and operation status
Output signalFFF,
LJ
(ON)t, +j ‘$;P$
Approx.0.7 sec.
1Output
signal waveforms and operation status
MotorOutput signal
Operates.stops.
(ON).l---l
Max. 60 sec.

BODY - Seat Belts23-45QRIVER’S SHOULDER BELT RELEASING OPERATION (TERMINAL
No.9)Status at input sideOutput signal waveforms and operation status
Motor
Output signal
Driver’s shoulder beltDriver’s door
is released.OpenOperates. H
(A)Driver’s shoulder beltNot released(OFF)
Other than as abovestops.:ONl -$<
Max. 60 setDriver’s shoulder beltlgnition switch
OFFis released.Operates.
03)Driver’s shoulder.beltNot released(“Release” switch)
(ON)
Key(Key-reminder switchNot in cylinder(OFF/ON)FFF)
1 ;: r
A/B)(ON1p-9 Max. 60 sec.
Other than as abovestops.
FRONT PASSENGER’S SHOULDER BELT FASTENING OPERATION (TERMINAL No. 18)
Status at input side
Ignition switch
Front passenger’s
shoulder belt(“Fasten” switch,
Door latch switch
“close”)
Other than as above
ONNot fastened
(ON, ON)Output signal waveforms and operation status
Motor
IOutput signal
Operates.- Max. 60 sec.
stops.
IFRONT PASSENGER’S SHOULDER BELT RELEASING OPERATION (TERMINAL No. 19)
Status at input sideOutput signal waveforms and operation status
Motor
Output signal
Front passenger’s
shoulder belt is
released.(A)

19/---..-_HEATERS AND AIR CONDITIONING
- Idle Speed Control24-9
Ii” E SPEED CONTROL
1.increasing idle speed to withstand air condition-
er load
When the compressor is placed in the ON state
with the engine at idle, the idling speed of the
engine will be increased by approx. 150 rpm to
prevent generation of vibration and also to
prevent the engine from stalling.-
2.The stepper motor types of actuators is used for
increasing the idle speed.
IDLE SOPEED CONTROL CIRCUITFusible link
Dedicatedfuse
Air
condi-tioner
compressor relay
I-gcfc
Lll
Compre:Ignition
switch
Sub fusible
linkswitch
Auto compressor
As
mlef kr Ihemo
Ax;,: engine control unit
Idle speed control
Y *e:Q
1
$4.1111.Pk+F)rmagneticIJ
clutchEngine controlunit13AO167