1990 MAZDA 232 oil pressure

A PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
pieziG-
INSPECT and ADJUST, if necessary, the following Items to
specification:
D Glass, exterior bright metal and paint for damage
Cl Wheel tug nuts
9 Trre pressures
LII All weatherstrips for damage or detachment
Z Operation of bonnet release and lock
D Operation of trunk lid, hatch and fuel lid opener
(it equipped)
3 Door operation and alignment
5 Headlight aiming
INSTALL the following parts:
D Wheel caps or rings (if equipped)
D Outside mirror(s)
[ UNDER BONNET-ENGINE OFF )
INSPECT and ADJUST, if necessary, the foIlowIng items to
specification:
Cl Fuel, coolant and hydraulrc lines, fittings, connections and
components for leaks
Cl Engine oil level
0 Power steering fluid level (if equipped)
D Brake master cylinder fluid levels
0 Clutch master cylinder fluid levels (if equipped) q
Windshield washer reservoir fluid level
D Radiator coolant level and specific gravity
Ll Tightness of water hose clamps
I3 Tightness of battery terminals, electrolyte level and specific
gravity
c) Manual transaxle oit level
D Drive belt(s) tension
C; Carburetor linkage (choke control, wide open throttle posi-
tion, etc.) (carburetor model only)
D Accelerator cable and linkage for free movement
D Headlight cleaner and fluid level (if equipped)
BLEED air from fuel line (diesel engine only)
CLEAN the spark plugs (except for diesef engine)
piicis-1
INSTALL the foflowing parts:
C Rubber stopper for inside rear view mirror (if equipped)
c! Fuse for accessories
CHECK the operation of the following items:
Cl Seat controls (sliding and redining) and head rest
ci Seat belts and warnrng system
Z! Ignition swrtch and steering lock
III Power window {if equipped)
0 Door locks including child proof door locks
0 Inhibitor switch
(ATX only)
Z All lights including warning and indicator lights
0 Ignrtron key reminder buyer (if equipped) Cl Horn, wipers and washers (front and rear, if equipped)
D Antenna (if equipped} q
Cigarette lighter and clock (if equipped)
I2 Remote controt outside mirror
(if equipped) q
Heater, defogger and air conditioner at various mode selec-
tions (if equipped)
c3 Sunroof (if equipped)
CHECK
the fotiowing items: q
Presence of spare fuse
c3 Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
Cl Operation and fit of windows
D Pedal height and free ptay of brake and clutch pedal
Cl Parking brake
i UNDER BONNET-ENGtNE RUNNING AT ]
1 OPERATtNG TEMPERATURE
CHECK the following items:
Cl Operation of idle-up system for air conditioner or power steer-
ing (if equipped)
13 Automatic transaxle fluid level
D Initial ignition timing
(except disel engine) q
Idle speed
El Operation of throttle position sensor (EGI engine)
13 Operation of cold start device and glow plug warning light
(diesel engine only)
D Operation of dash pot [EGI engine)
t
ON HOtST 1
CHECK the following items:
U Underside fuel, coolant and hydraulic lines, fittings, connec-
tions and components for leaks q
Tires for cuts or bruises
Cl Steering linkage, suspension, exhaust system and all under-
side hardware for
looseness or damage
1 ROAD TEST 1
CHECK the foliowing items:
II Brake operation
D Clutch operation
0 Steering control
c3 Operation of meters and gauges
0 Squeaks, rattles or unusual noises q
Engine general performance
c3 Emergency Iocking retractors
rAFTER ROAD TEST 1
REMOVE the seat and floor mat protective covers
CHECK for the necessary
owner information materials, tools
and spare tire in vehicle
93EOAX-002
A-2

A SCHEDULED MAINTENANCE SERVICES (Europe)
Maintenance Number of months or km (mires), whichever comes first
Months” - 6 12 18 24 30 1 36 42 48
Maintenance KIlometers 1,000 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000
(Miles)
(600) 1 (6,000) j(12,OOO) (18,000) (24,000) (30,000) (36,000) (42,000) \(48,000) Chassis and body [Cont’d)
Steerrng and front suspension I
I
1 1 I I
MTX oil
A A A
R A A A R
Rear axle oil R A A R 1 A A A R
Trabsfercarrter oil
I R I A A R A A A R
B&s. nuts on chassis and body T 1 1 T T
T I T
Body condition (Visual
onfy) t nspect annually
Exhaust system hear shields I i
Tires (tncluding spare ttres) wtth rnflation
pressure adjustment t I I 1
Hinges and catches
A
bA4 ,A3 A
Understde of vehicle
i I I I I
Seat belt
I I I t
Road test
1 I I 1
Driveshafi dust bouts
I I I 1
93GOAX-709
A-10

Bl SUPPLEMENTAL SERVICE tNFORMAT1ON, REMOVAL
SUPPLEMENTAL SERVICE INFORMATION
The following points in this section are changed in comparison with Workshop Manual [Europe (I 203-I U-89F),
Australia (1204- 1 O-89!=)].
Engine
l Removal
l Installation 93GOF31-705
REMOVAL
Warning
w Release the fuel pressure.
PROCEDURE
1. Disconnect the negative battery cable.
2. Drain the engine coolant and transaxle oil.
3. Remove in the order shown in the figure, referring to Removal Note.
Step 1
t
I
*ATX ONLY 1
93GOBl-706
1. Undercovers
2. Side covers
3. Resonance chamber and air cleaner assembly
4. Battery bracket, cover and bafiery
5. Battery carrier and battery duct
6. Accelerator cable
7. Radiator hose
8. Coolant reservoir hose
9. Cooling fan connector
IO. Radiator switch connector (ATX)
1 f . A/C cut switch connector (ATX) 12. Oil cooler hoses (ATX)
13. Radiator bracket
14. Radiator and cooling fan assembly
15. P/S and/or A/C drive belt
16. P/S oil pump and bracket
Removal Note .._...._...__......... . . . . . . . page BY -7
17. A/C compressor
Removal Note.. . . . . . . . . . . . . . .._. . . . . . . . ._. page Es1 -7
i 8. Crossmem ber
19. A/C compressor bracket
20. Coolant reservoir
61-6

REMOVAL Bl
/
/
93G05? -72t
Removal note
P/S oil pump
Caution
l Do not damage the hoses.
I _ Remove the P/S oil pump with the hoses still connected.
2. Position the pump away from the engine and secure it with
wire.
A/C compressor
Caution
l Do not damage the hoses.
1. Remove the AC compressor with the hoses still connected.
2. Position the compressor away from the engine and secure
it with wire.
Step 2
1. Disconnect the harness connectors shown in the figure.
DIFFERENTIAL
DIFFERENTIAL
LUCK SENSOR
OIL PRESSURE SWITCH --- -
GROUND
r, IDLE SPEED CONTROL
NEUTRAL SWITCH
’ SOLENOID VALVE w MTX!
(ECE WITHOUT _--------I
CATALYST) BACK-UP LIGHT SWITCH
\‘C
Y ~55 ATX’
d ---a-- ,-,---1
INHIBITOR SWITCH

91 1NSTALLATION
Step 4
1. Connect the hoses shown in the figure.
Caution
l Position the hose clamp in the original location on the hose, and squeeze it lightly with large
pliers to ensure a good fit.
Step 5
1. Connect the harness connectors shown in the figure.
OIL PRESSURE SWITCH
Df STRlBUTdR
OXYGEN SENSOR
(EXCEPT ECE
WITHOUT CATALYST) lVFFFRFh!TIAI
-.I I -4 m-m. I -r-h LOCK SENSOR DIFFERENTIAL
THRO77LE
/--+I / LOCK MOTOR
AC. .A--
r IDLE SPEED CONTROL
r
dz k
/NEUTRAL SWITCH
“Rou2ydy __
HEAT GAUGE UNIT ’
IDLE-UP
SOLENOID VALVE
IECE WlTl-tOUT
‘CATALYST-)
BACK-UP LIGHT SWITCH INHlBlTdR SWITCH
G3UOBX-837
E3i -20

B2 REMOVAL
REMOVAL
Warning
l Release the fuel pressure. (Refer to Section FZ.)
PROCEDURE
i. Disconnect the negative battery cable.
2. Drain the engine coolant and transaxle oil.
3. Remove in the order shown in the figure, referring to Removaf Note
Step 1
1. Strut tower bar
2. Undercovers and side covers
3. Air cleaner assembly
4.
Battery bracket
5. Battery cover
6. Battery
7. Battery carrier
8. Accelerator cable
9. Radiator hoses
10. Coolant reservoir hose
f I. Cooling fan connector
12. Radiator switch connector
13. Radiator bracket
14. Radiator and coofing fan assembly
15. Battery duct
16. Air pipe and air bypass valve
17. Intercooler and air pipe
Removat Note . . . . . . . . . . . . .._.. m _._._..., page 82-U
18. Air pipe and gasket
19. P/S and/or AK drive bett
20. P/S oil pump and bracket
Removal Note . . . . .._.__.....~..~........ page BZ-13
21. A/C compressor
Removal Note . . . . . .._................... page 82-I 3
22. Crossmember
02-12

B2 REMOVAL
Step 2
1. Disconnect the harness connectors shown in the fiuure.
ALTERNATOR OIL PRESSURE SWITCH
\. PRESSURE REGULATOR
STARTER
CObjTROL VAVLE
E-SPEED CONTROL
CTOR
KNOCK SENSOR
SWITCH
03 w 08X-80’
Step 3
I. Disconnect the hoses shown in the figure.
-
------a-
93GOB2-720
82-14

B2 INSTALLATION
Step 5
1. Connect the harness connectors shown in the figure.
ALTERNATOR OIL PF;IESSURE SWITCH PRESSURE REGULATOR
STARTER CONTROL VAVLE
GRoYD O-i-l-tE SENSOR
IDLE-SPEED CONTROL
KNOCK SENSOR
OXYGEhENSO$
Step 6
Torque Specifications
03UO8X-33’
7.8-11 N-m
(80-110 cm-kg, 69- .
11 N-m (80--f ’IO cm-kg, 69-95 in-lb)
N-m
cm-kg, 69-95 in-Ib)
37-52 (3.8-5.3, 27
7.8--fl N-m (80 107 (9.6-T 1.9, 69-79)
N-m (m-kg, ft-lb)
03U03X-83