1989 MITSUBISHI MONTERO tire type

.$i ~[ r
18 INTRODUCTION AND MASTER TROUBLESHOOTING - Towing and Hoisting
HOISTING
POST TYPE
Special care should be taken when raising the vehicle on a
frame contact type hoist. The hoist must be equipped with
the proper adapters in order to support the vehicle at the
proper locations. (Shown in the illustration)
Conventional hydraulic hoists may be used after determining
that the adapter plates will make firm contact with the side ._
frame.
FLOOR JACK
A regular floor jack may be used under the front crossmember
or rear axle housing.
Caution
1. A floor jack must never be used on any part of the
underbody.
2. Do not attempt to raise one entire side of the vehicle by
placing a jack midway between front and rear wheels.
This practice may result in permanent damage to the
body.
EMERGENCY JACKING
Jack receptacles are located at the No. 2 crossmember and .
rear axle housing to accept the jack supplied with the vehicle
for emergency road service. Always block the opposite wheels
and jack only on a level surface.
FRAME CONTACT SUPPORT LOCATIONS
1,175 mm (46.3 in.)
Wheel base
2.350 mm (92.5 in.) Sectlon A-A
NOTE
The
locations of the support point shown as Section A-A are
the same as those of the twin post hoist shown in the next
paw.
1 TSB Revision
I -

INTRODUCTION AND MASTERTROUBLESHOOTING - GeneralDataandSpecmcations 21
L042G L141G
TNSL FM TNJL F/H
TRJL F/H TRUL F/H
Engine
Model No. G54B 6672 6672 6672
Type In-line OHC V-type, OHC V-type, OHC
V-type, OHC
Number of cylinders 4 6 6 6
Bore 91.1 mm(3.59in.j 91.1 mm(3.59in.j 91.1 mm(3.59in.) 91.1 mm(3.59in.
Stroke 98.0 mm (3.86 in.) 76.0 mm (2.99 in.) 76.0 mm (2.99 in.) 76.0 mm (2.99 in.
Piston displacement 2,555 cm3 2,972 cm3 2,972 cm3 2,972 cm3
(155.9 cuin.) (181.4cu.in.) (181.4cu.in.) (181.4 cuin.)
Compression ratio 8.7 8.9 8.9 8.9
Firing order 1-3-4-2 1-2-3-4-5-6 I -2-345-5 1-2-3-4.5-8
Basic ignition timing 7”BTDC 22” 5”BTDC 22” 5”BTDC i 2” 5”BTDC +-2”
Transmission &transfer case
Model No. KM145 V5MTl KM148 KM148
Type S-speed manual 5-speed manual &peed automatic &peed automatic
Gear ratio
Transmission 1st 3.967 3.918 2.826 2.826
2nd 2.136 2.261 1.493 1.493
3rd 1.360 1.395 1 .ooo 1.000
4th 1 .ooo 1.000 0.688 0.688
5th 0.856 0.829 -
Reverse 3.587 3.925 2.703 2.703
Transfer case High 1 .ooo 1 .ooo 1 .ooo 1 .ooo
Low 1.944 1.925 1.925 1.925
Final ring ratio gear 4.625 4.625 4.625 4.625
Clutch
Type Dry single disc & Dry single disc & -
diaphragm spring diaphragm spring
Chassis
Tire size
Front suspension
Type
Rear suspension
Type
Brakes
Type Front
Rear P225ff 5Rl5 P235ff5Rl5
independent Independent double-wishbone
double-wishbone
Rigid axle Rigid axle
Disc Disc
Drum Drum (Leading and trailing)
(Leading and trailing)
Power steering
Gear type
Gear ratio
Fuel tank capacity Integral type Integral type (Recirculating ball nut)
(Recirculating ball nut)
16.4 16.4
liters (gals.) 60 (15.9) 75 (19.8)
[ TSB Revision

-_-
22 INTRODUCTION AND MASTER TROUBLESHOOTING - General Data and Specifications
<&door vehicles>
L-
chicle dimensions mm (in.)
Overall length
Withoutspare tire a
With spare tire @
Overall width 0
Overall height @
Wheelbase Q
Tread Front @
Rear 8
Overhang Front @
Rear @
Height at curb weight
Wt.)
Front bumperto ground @
Rear bumper to ground 0
Minimum running ground @
clearance
Angle of approach 8
Angle of departure
8
Ramp breakover angle
63
,hicle weights kg (Ibs.)
Curb weight
Gross vehicle weight rating
Gross axle Front
weight rating
Rear
Seating capacity
gine
Model No.
Type
Number of cylinders
Bore
Stroke
Piston displacement
Compression ratio
Firing order
Basic ignition timing VMNJL F/H VMRJL F/H
4,570 (179.9)
4,605 (181.3)
1,680 (66.1)
1,890 (74.4)
2,695 (106.1)
1,400 (55.1)
I,41 5 (55.7)
745 (29.3)
1 ,I 65 (45.9) 4,570 ( 179.9)
4,605(181.3)
1,680 (66.1)
1,890 (74.4)
2,695(106.1)
1.400(55.1)
1,415 (55.7)
745 (29.3)
1,165(45.9)
490 (19.3)
450(17.7)
215 (8.5) 490 (19.3)
450(17.7)
215 (8.5)
38”
28”
18” 38”
28
18”
-i
1,780 (3,924)
2,400 (5,291)
1,100(2,425)
1,600 (3,527)
5 1,795 (3,957)
2,400 (5,291)
1,100(2.425)
1,600 (3,527)
5
6672
V-type, OHC
6
91 .I mm (3.59 in.)
76.0 mm (2.99 in.)
2,972 cm3 (181.4 cu.in.)
8.9
l-2-3-4-5-6
5”BTDC i2” 6672
V-type, OHC
6
91 .l mm (3.59 in.)
76.0 mm (2.99 in.)
2,972 cm3 (181.4 cuin.)
8.9
1-2-3-4-5-6
5”BTDC 22” : L146G
L
_-. 1 TSB Revision I
.- WMRUL F/H
4.570 (179.9)
4,605 (181.3)
1,680 (66.1)
1,890 (74.4)
2,695(106.1)
1,400(55.1)
1,415 (55.7)
745 (29.3)
1,165 (45.9)
490 (19.3)
450 (17.7)
215 (8.5)
38”
28”
18
1,805 (3,979)
2,400 (5,291)
1 ,100 (2,425)
1,600 (3,527)
5
3072
V-type, OHC
3
31 .l mm (3.59 in.)
76.0 mm (2.99 in.)
2,972 cm3 (181.4 cu.in.)
3.9
l-2-3-4-5-6
5”BTDC 22”

INTRODUCTION AND MASTER TROUBLESHOOTING - General Dataand Swxifications 23
Transmission &transfer case
Model No.
Type
Gear ratio
Transmission 1 St
2nd
3rd
4th
5th
Reverse
Transfer case High
Low
Final ring gear ratio
Elutch
Type
Chassis
Tire size
Front suspension
Type
Rear suspension
Type
Brakes
Type Front
Rear
Power steering
Gear type
Gear ratio
Fuel tank capacity liter (gal.) VMNJL F/H VMRJL F/H WMRUL F/H
EMT1 KM148 KM148
5-speed manual 4-speed automatic 4-speed automatic
3.918
2261
1.395
1.000
0.829
3.925
1.000
1.925
4.625 2.826 2.826
1.493 1.493
1 .ooo 1 .ooo
0.688 0.688
2.703
1 .ooo
1.925
4.625 -
2.703
1 .ooo
-1.925
4.625
Dry single disc &
diaphragm spring
P235ff 5 R 15 L146G
7
Independent doublewishbone
Rigid axle
Disc
Drum (Leading and trailing)
Integral type (Recirculating ball nut)
16.4
92 (24.3)
1 TSB Revision