1989 MAZDA 323 battery

t FAN RELAY
FAN RELAY
REMOVAL / INSPECTION
1. Disconnect the negative battery cable.
2. Remove the fan relay in a place shown in the figure.
FAN RELAY
BP ATX)
l o... . ,. . . . . . . . . . TYPE 1 @ No.2 FAN RELAY
(FOR !3P ATX)
@AND @ . . . ..TYPE 2
03UOEX-029
[TYPE l] [TYPE 21
INSPECTION
1. Check continuity as shown with an ohmmeter.
Contir
No
Yes Terminal
m-0
OS-@
2. Apply 12V between terminals @ and @.
Check for continuity between terminals @ and 0.
3. If not as specified, replace the fan relay. .-
._/ ’

F TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
ENGINE CONTROL OPERATION CHART
Note
Input Device and Engine Conditions
l The data in this chart is for reference only.
INPUT DEVICES APPROX,- SENSORS
MATE TIME G& THROTTLE SENSOR
(BASED ON TRIBUTOR
WATER INTAKE
10-16°C, (G. OXYGEN AIRFLOW AIR
VT
POW
.50-6OOF
SIGNAL)” ;;;;;f- SENSOR METER
AMBIENT) (Ne-SIGNAL) THERMO- TERMINAL TERMINAL yE\MINAL
CONDITIONS SENSOR (ATX)
WX)
A
c
CRANKING
-COLD ENGINE Signal has Signal has Signal has Signal has Slgnal has Slgnal has
l COLD AIR zero no affect no effect no effect no effect no effect
no effect
. COLD COOLANT on ECU on ECU on ECU on ECU on ECU
on ECU
Cool to A A
COLD START
warm: Low volume Closed Closed
Closed
-FAST IDLE
One
Medium airflow: throttle: throttle:
l COLD AIR
minute
voltage High volt-
Low volt- Low volt- throttle.
Low volt-
* COLD COOLANT
(3.5” and :zo:o, ,,Pbove 1’,“,“$; a(ogi-O,8”) ;149&“) we W)
dropping) to high
(68OF)]:
COLD DRIVEAWAY voltage A
Above
-PART THROTTLE Two (O-0.9”) 2.3”
l COLD AIR minutes
l COLD COOLANT
v v ,,
Warm: Medi- Sensor Moderate II
WARM DRIVEAWAY
volume air-
-PART THROTTLE Three N&IGNAL um voitage hot:
flow: Low
l WARM AIR minutes Sends all Vvwrox switching l WARM COOLANT cylinders 0.7V and
from high to medium
Part Part
TDC signal dropping) voltage voltage
throttle: throttle.
)
A (0.9V) (1 .o-3.5”)
to ECU
.“~ Medium Medium
HOT CRUISE
s voltage voltage
Open
l WARM AIR G-
SIGNAL”’ to low (0.8-3.0”) (4.5-5.5”) throttle:
l WARM COOLANT High
Sends No. voltage
1 cylinder (0.1”) voltage
1 (battery
TDC (com-
1 I voltage)
HOT ACCELERATION pression)
-60% THROTTLE signal to
Moderate
ECU
to strong
High Cool lo warm
voltage ;$,“,” Of j-20-4OT
f t
HOT ACCELERATION
More’ than Hot: Low (0.9”) Low (-4-‘04”F)l: W,ds open
voltage 1.5-4.3v
throttle: Wide open
-WIDE OPEN
four voltage
High volt- throttle
THROTTLE (0.5-1.5V)
minutes (Below High
0.5”) age (Above
voltage (OV)
t 1 3.OV)
I,
A 1. /I
DECELERATION
-CLOSED THROTTLE
HOT CURB IDLE
-EXTENDED
HOT ENGINE
SHUTDOWN Low
voltage
(0”) Low Closed Closed
Closed
volume throttle: throttle.
throttle.
of airflow:
~~~~!$$ (Above Low Low
Low
voltage voltage
voltage
to low 3.OV) (0.2-0.N) (4.5-5 5V) (OV)
voltage
(0.75%
t t 1 0.25”)
r v 1 I I
Sensor
hot: Low
OFF OFF voltage
-
(0.1”) until OFF OFF OFF OFF
OFF
sensw
COOIS
._-

TROUBLESHOOTING GUIDE F
r
- SENSORS
z-----
‘RES-
‘URE
‘WITCH FRL (Dsy
ime Run-
ling
.ight)
:ONTROL
INIT
CANADA]
)FF
3attery
oltage)
T- IEUTRAL
rND
:LUTCH
iWITCHES
MTX) IIAGNOSIS
:ONNEC-
‘OR TEN
‘ERMINAL
rEST
‘ERMINAL) IGNITION SWITCH
s kgnal has
r IO effect
C In ECU
I neutral:
.ow volt-
rge signal
II ECU
w
-
f
I
Iriving in
iny gear:
iigh volt-
ige signal
o ECU
Battery TOP-
IGHT
WITCH UHIBITOR
iWITCH
4TX) L/C
;WITCH
5
IL
IGNAL
Sl ignal has
nl 3 effect
01 n ECU
H
0
F-f
S
C
VI
si
E
te
VI
C
VI
si
i
1 T
eadlight
r rear
‘indow
efroster
Nitch
IN: High
pltage
gnal to
CU (Bat-
try
sltage)
IFF: Low
altage
gnal to
cu
3elow
.5V)
B
S'
0
C,
C
L
E
E
II
(
\i
c
E
t’
I lower
Nitch**
r Electri-
al fan
IN: Low
foltage
signal to
iCU (Be-
3w 1.W)
IFF: High
loltage
rignal to
ICU (Bat-
ev
voltage)
I
OFF ITART
‘OSITION IN
OSITION
‘ends sig
al to
CU (Bat-
?ry
oltage) #ignal has
0 effect
#n ECU ignal has
0 effect
n ECU ignal has
0 effect
n ECU ;ignal has
IO effect
rn ECU ignal has
0 effect
n ECU
rake pedal Ggnal has
IQ effect
In ECU
1NorP
ange: No
ignal to
.cu
w
-
7D
ange: No
#ignal to
.cu
Battery
foltage)
- - - - -
ends sig-
31 to ECU
jattr ?ry
Atac
-2
/heel -
Jrned:
ow volt-
ge signal
I ECU
3elow
.5V)
teering
/heel
traight
head:
ligh volt-
ge signal
) ECU
dattery .erminal
lot
Irounded:
iigh volt-
tge Signal
3 ECU
Battery
roltage)
‘erminal
Irounded:
.ow volt-
rge signal
3 ECU
Below lo signal
ent to
cu
3elow
5V) r/C switch
IN:
iends sig-
ial to
CU (Be-
IW 1.5V)
r/C switch
IFF: No
ignal to
CU (Bat-
3ry
‘oltage) )RL ON:
w ends sig-
al to
CU (Bat-
2ry
oltage) lo signal
3 ECU
3elow
.5V) )RL OFF:
3attery
oltage)
I .5V’
medal
Sends
signal to
KU
Battery
voltage)
- -
In N or P
range:
Sends sig-
nal to ECU
PV In neutral:
Low volt-
age stgnal
to ECU
(W
I -
- - -
OFF OFF OFF OFF OFF OFF OFF
OFF OFF
23UOFX-0’
+’ Blower switch: 2nd position or more
F-21

F TROUBLESHOOTING GUIDE
Troubleshooting chart
6 I
CRANKS NORMALLY BUT HARD TO START - WHEN ENGINE COLD
*Engine cranks at normal speed but requires excessive crankmg time before starting
IESCRIP-
l Batterv in normal condition
llON l Restans OK after warmup l Engine runs normally at idle [If Idle condrtron is not OK, refer to “Rough idle” (Nos. S-12)]
TROUBLESHOOTING HINTS]
B Air/Fuel mrxture too rrch @Air/Fuel mixture too lean
l Arrflow meter stickrng l Fuel iniectron control malfunction
l Aw cleaner element clogged
*Idle weed control malfunction (Correction for coolant temperature)
0 Poor atomizatron
- ~~ ~~ *Low RVP (summer) fuel is used rn cold weather >
f INSPECTION T Check If “00” is displayed on Self-Diagnosis
Checker wth Ignition switch ON -
Yes
No CT page F-73
SYSTEM SELECT: 1
“SELECT SW: A
Check if ECU terminal voltages are OK
(Especially 1C. 2D. and 2Q)
cc page F-144
Check If engine starts easily when throttle valve -
Yes
-
NO
-
Yes ACTION
Go to next step
Malfunctlon Code No. dlsplayed
Check for cause (Refer to specified
check sequence)
“58” flashes CT- page F-79
Check ECU terminal 1F voltage
Speciflcetlon: Battery voltage CT page F-144
(Ignition ewltch ON)
+ If OK, replace ECU CT page F-143
e If. not OK, check wrring between
ECU and Self-Diagnoos Checker
Go to next step
Check for cause CI page F-145
(-!hnrlr ,‘ ICP ..-I..- .^ nv
c+ page F-103
13UOFX-009
DESCRIPTION:
Further describes the symptom. Confirm that the chart addresses the actual symptom before beginning
troubleshooting.
TROUBLESHOOTING HINTS:
This describes the possible point of malfunction.
STEP:
This shows the order of troubleshooting. Proceed with troubleshooting as indicated.
INSPECTION:
This describes an inspection to quickly determine the malfunction of parts. If a detailed procedure is necessary
to perform the INSPECTION, refer to the page shown by the “~7” mark.
ACTION:
This recommends the appropriate action to take as a result (Yes/No) of the INSPECTION. How to perform
the action is described on the reference page shown by the “~7” mark.
OWOFX-016
F-26

F TROUBLESHOOTING GUIDE
SYMPTOM TROUBLESHOOTING
2 CRANKS NORMALLY BUT WILL NOT START (NO COMBUSTION)
l Engine cranks at normal speed but shows no sign of “firing”
DESCRIP-
*Battery in normal condition
TION
*Throttle valve not held fully open while cranking (Dechoke system not operate)
*Fuel in tank [TROUBLESHOOTING HINTS]
Because of no combustion, possibly no fuel is injected to engine or no ignition at all cylinders
:I) No spark
@I Low fuel line pressure
l Ignition control malfunction
@ Low engine compression l Ignition system component malfunction
3 No fuel injection
l Fuel pump inoperative l Injectors inoperative
TEP INSPECTION
ACTION
1 Check if strong blue spark is visible at discon-
Yes Go to Step 3
netted high-tension lead
No Go to Step 2
2 Check if “00” is displayed on Self-Diagnosis
Yes Check ignition system (Refer to
Checker with ignition switch ON
Troubleshooting “Misfire”) w page G-5
w page F-82
No Service Code No. displayed
Check for cause (Refer to specified
check sequence) w page F-83
“88” flashes
Check ECU terminal 1F voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
W: SELF TEST e If OK, replace ECU w page F-149 c3 If not OK, check wiring between
SELECT SW: A ECU and Self-Diagnosis Checker
3 Connect diagnosis connector terminals F/P and
Yes Check if engine starts in this condition
GND with jumper wire and check for fuel pump
operating sound with ignition switch ON c3 If starts, check circuit opening relay c7 page F-129
w page F-125
c3 If does not start, go to Step 5
DIAGNOSIS C
Go to next step ._-,
._. ,
F-30

F TROUBLESHOOTING GUIDE
3 CRANKS NORMALLY BUT WILL NOT START (PARTIAL COMBUSTION) - WHEN ENGINE COLD
DESCRIP- *Engine cranks at normal speed but shows only partial combustion and will not continue to run
TION
l Battery in normal condition
*Fuel in tank
[TROUBLESHOOTING HINTS]
0 Air/Fuel mixture too rich
*Air cleaner element clogged
l Airflow meter stuck @ Low engine compression
@ Air/Fuel mixture too lean
l Fuel injection control malfunction
(Correction for coolant temperature)
*Low fuel line pressure
*Air leakage of intake air system
Checker with ignition switch ON
CT page F-83
w page F-150
Specification: Battery voltage
(Ignition switch ON)
W: SELF TEST w page F-149
Fuel line pressure:
285-314 kPa (2.7-3.2 kg/cm’, 38-48 psi) If fuel line pressure quickly in-
creases, check pressure regulator CF- page F-129
d If fuel line pressure gradually in-
creases check for clogging be-
I pump and pressure
Check if fuel return hose is clogged or
F-32

F TROUBLESHOOTING GUIDE
4
CRANKS NORMALLY BUT WILL NOT START (PARTIAL COMBUSTION) - AFTER WARM-UP *Engine cranks at normal speed and shows partial combustion but will not continue to run after running and
DESCRIP- hot soaked
TION *Battery in normal condition
*Engine starts normally when cold
[TROUBLESHOOTING HINTS] 3 Air/Fuel mixture too rich
@ Vapor lock
l Insufficient fuel injection control
*Fuel pressure not held in fuel line after engine stopped
(Correction for coolant temperature)
*High RVP (winter) fuel used in warm weather
l Injector fuel leakage @ Pressure regulator control system malfunction [BP]
switch ON, then check if en
D‘ page F-134
Fuel line pressure:
265-314 kPa (2.7-3.2 kg/cm’, 36-46 psi) ne pressure w
+ If fuel line pressure quickly in-
if fuel return hose is clogged
or
F-=34

TROUBLESHOOTING GUIDE F
TEPt INSPECTION ACTION
Fuel line pressure:
More than 147 kPa (1.5 kg/cm*, 21 psi)
w page F-125
4 If OK, check injector for fuel
w page F-132
w page F-127
w page F-158
+ If OK check connections of water
osensor and ECU 2Q terminal
check connections of water
osensor and ECU 2E terminal
K, replace water ther-
w page F-83
w page F-150
Specification: Battery voltage
(Ignition switch ON)
Q If OK, replace ECU CT page F-149
+ If not OK, check wiring between
ECU and Self-Diagnosis Checker
23UOFX-0:
F-35