1988 FORD BRONCO ECU

42
*
[SR16370(BEF )04/95]
4. Insert the belt tongue into the buckle for that
seating position until you hear and feel the
latch engage. Figure 3. Make sure tongue is
latched securely to buckle by pulling on
tongue.
*
[SR16375(BEF )04/95]
half page art:0011240-B
Buckling the belt
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

46
*
[SR16410(BEF )04/95]
7. Before placing the child in the child seat,
forcibly tilt the seat from side to side, and
tug it forward to make sure that the seat is
securely held in place, Figure 7.
*
[SR16412(BEF )04/95]
half page art:0011244-A
Checking that the seat is secure
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

47
*
[SR16415(BEF )04/95]
8. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode,
Figure 8.
*
[SR16420(BEF )04/95]
half page art:0011245-B
Checking the retractor
*
[SR16425(BEF )04/95]
9. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
*
[SR16430(BEF )04/95]
To remove the retractor from automatic lock
mode, allow webbing to retract fully to its
stowed position and the retractor will
automatically switch back to the vehicle sensitive
locking mode for normal adult usage.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

48 [SR16440(BEF )04/95]Installing a Child Safety Seat at the Rear
Center Seating Position with Locking
Adjustable Lap Belt
[SR16450(BEF )04/95]
1. Lengthen the lap belt. To lengthen the belt,
hold the tongue so that its bottom is
perpendicular to the direction of webbing
while sliding the tongue up the webbing.
[SR16455(BEF )04/95]
2. Place the child safety seat in the center
seating position.
[SR16460(BEF )04/95]
3. Route the tongue and webbing through the
child seat according to the child seat
manufacturer's instructions.
[SR16465(BEF )04/95]
4. Insert the belt tongue into the proper buckle
for the center seating position until you hear
a snap and feel it latch. Make sure the
tongue is securely fastened to the buckle by
pulling on tongue.
[SR16470(BEF )04/95]
5. Push down on the child seat while pulling
on the loose end of the lap belt webbing to
tighten the belt.
[SR16475(BEF )04/95]
6. Before placing the child into child seat,
forcibly tilt the child seat from side-to-side
and in forward directions to ensure that the
seat is held securely in place. If the child
seat moves excessively, repeat steps 5
through 6, or properly install the child seat
in a different seating position.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

52
*
[SR16535(B )04/95]
5. Insert the belt tongue into the proper buckle
for that seating position until you hear a
snap and feel it latch. Make sure the tongue
is securely latched to the buckle by pulling
on the tongue. See Figure 3.
*
[SR16540(B )05/95]
half page art:0011365-A
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

54
*
[SR16555(B )04/95]
7. Grasp belt close to child seat and pull on the
shoulder belt portion of the combination
lap/shoulder belt, then allow the belt to
retract and remove all slack to securely
tighten the child safety seat in the vehicle.
See Figure 5.
*
[SR16560(B )05/95]
half page art:0011367-A
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

55
*
[SR16565(B )04/95]
8. Before placing the child into the child seat,
forcibly tilt the child seat from side-to-side
and in forward directions to make sure that
the seat is held securely in place. See Figures
6 and 7. If the child seat moves excessively,
repeat steps 6 through 8, or properly install
the child seat in a different seating position.
[SR16570(B )05/95]
half page art:0011368-AFile:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com

57
*
[SR18400(BEF )04/95]
Attaching Safety Seats With Tether Straps
*
[SR18410(BEF )03/01]
General Instructions
[SR18413(BEF )02/95]
Some manufacturers make safety seats that
include an upper tether strap that goes over the
seatback and attaches to an anchoring point.
Other manufacturers offer the tether strap as an
accessory. Contact the manufacturer of your
child safety seat for information about ordering
a tether strap.
*
[SR18417(B )12/91]
You can attach a tether strap anchor bracket to
the rear floor by using a tether anchor kit
(613D74), available at no charge from any Ford
dealership.
*
[SR18420(BEF )03/91]
Read and follow the instructions provided with
the kit carefully for installation of the child
tether strap anchor.
*
[SR18501(BEF )03/91]
Follow the child seat manufacturer's instructions
to attach the tether strap to the tether bracket.
*
[SR18700(B )04/95]
Ford recommends placement of tethered safety
seats in a rear seating position with the tether
strap installed to the tether anchoring point as
shown in the instructions provided with the
child tether strap anchor kit.
[SR18875(B )04/95]
This vehicle has provisions to install a tether
anchorage in the front, right hand and all second
row seating positions. It is easiest to install a
tether anchor at the second row, rear, center
seating position.
[SR18900(B )03/91]
If the tethered seat is installed in the front seat,
Ford recommends the center front seating
position, with the tether strap secured to the
center rear lap belt tongue or to the webbing of
the buckled center rear lap belt behind the child
safety seat. The front, right hand seating position
may be used if it is the only seating position
available.
File:ltsrb.ex
Update:Tue Jun 20 16:58:10 1995
ProCarManuals.com